Cambridge B08DCGTZR9 3 Inch Swing Arm Wall Lamp Instruction Manual

Cambridge B08DCGTZR9 3 Inch Swing Arm Wall Lamp

Product Information

The product is a wall-mounted light fixture that comes with a mounting plate, backplate, harp, socket base, shade, finial, mounting channel, cord covers, power cord, wire connectors, and decorative caps. The fixture can be installed on a flat wall surface or an electrical junction box.

Package Contents

• Mounting Plate (A)
• Backplate (D)
• Backplate Screws (E)
• Harp (H)
• Socket Base (G)
• Shade (I)
• Finial (J)
• Mounting Channel (K)
• Cord Covers (L)
• Power Cord (M)
• Wire Connectors (C)
• Decorative Caps (F)

Installation Requirements

• Screwdriver
• Wood screws (for fastening to a wall stud)
• Plastic anchors (for fastening to a hollow area)
• Electrical junction box (for junction box installation)

Product Usage Instructions

Flat Wall Surface Installation

1. Unpack the fixture and check that all items on the parts diagram are included in the box.

2. Unscrew Backplate Screws (E) to remove Mounting Plate (A) from Backplate (D).

3. Position Mounting Plate (A) on the desired location on the
   wall, ensuring the Backplate Screw (E) holes on Mounting Plate (A) are positioned on the left and right.

4. Fasten Mounting Plate (A) to the wall:

   • If fastening to a wall stud: Secure using (4) wood screws and
     screwdriver.

   • If fastening to a hollow area: Mark the location to install
     plastic anchors. Drill 1/4 pilot holes on the marked spots and
     insert plastic anchors. Affix to anchors.

5. Place Backplate (D) against the wall, ensuring the holes on each side of Backplate (D) align with the holes on Mounting Plate (A). Secure Backplate (D) to Mounting Plate (A) with Backplate Screws (E).

6. Insert Harp (H) into Socket Base (G) by squeezing legs together.

7. Install light bulb (not included).

8. Place Shade (I) on Harp (H) and secure using Finial (J).

9. Position Mounting Channel (K) on the wall between Backplate (D) and the floor. Note: Both Cord Covers (L) snap onto (1) Mounting Channel (K).

10. Fasten Mounting Channel (K):

    • If fastening to a wall stud: Secure using (4) wood screws and screwdriver.
    • If fastening to a hollow area: Mark location to install plastic anchors. Drill 1/4 pilot holes on the marked spots and insert plastic anchors. Affix to anchors.

11. Place Power Cord (M) into Mounting Channel (K) and affix first Cord Cover (L) over the upper half of Mounting Channel (K). Affix second Cord Cover (L) to the bottom half of Mounting Channel (K).
    Note: If Cord Covers (L) do not snap into place, widen Mounting Channel (K) by gently pulling it apart.

12. Plug Power Cord (M) into an outlet.

Junction Box Installation

1. Unpack the fixture and check that all items on the parts diagram are included in the box.

2. Unscrew Backplate Screws (E) to remove Mounting Plate (A) from Backplate (D).

3. Remove Power Cord (M):

   • Turn Wire Connectors (C) in a counter-clockwise direction to
     detach Power Cord (M) from fixture wires.

   • Undo the safety knot on Power Cord (M) and remove it from the
     bottom of Backplate (D).

4. Secure Mounting Plate (A) to the junction box (not included) using Mounting Screws (B) provided, ensuring the Backplate Screw (E) holes on Mounting Plate (A) are positioned on the left and right.

5. Using the wire graph below, connect the appropriate wires from the fixture to the corresponding wires in the electrical junction box (not included) and secure Wire Connectors (C).

   • Connect the ground wire (bare copper or green) from your fixture to the:
   1. the ground wire in the junction box, or
   2. ground screw in the junction box
   • Connect the BLACK house wire to the fixture hot wire that corresponds to the diagram (black, round & smooth, white/grey with tracer, brown/gold without tracer).
   • Connect the WHITE house wire to the fixture neutral wire that corresponds to the diagram (white, ribbed/ridged, white/grey without tracer, brown/gold with tracer).

6. Place all wires and Wire Connectors (C) back into the junction box.

7. Place Backplate (D) against the wall, ensuring Backplate Screws (E) are protruding through the holes in Backplate (D). Secure the fixture in place to the Mounting Plate (A) with Decorative Caps (F).

IMPORTANT SAFETY INSTRUCTIONS

• To avoid injury or damage, mount only on a surface that is sturdy.
• To avoid electric shock, make sure the electricity is turned off at the main circuit breaker panel. If you are replacing an existing fixture, turn off the following in order: fixture, wall switch, and main fuse or breaker box. Note: Some types of fuses must be unscrewed to shut the power off.
• If you are unclear as to how to proceed, please consult a licensed electrician.
• UNPACK THE FIXTURE: Check the contents of the box. Box should contain all items on the parts diagram.

INSTALLATION INSTRUCTIONS

FLAT WALL SURFACE See next page for junction box installation

1. Unscrew Backplate Screws (E) to remove Mounting Plate (A) from Backplate (D).
2. Position Mounting Plate (A) on desired location on the wall ensuring the Backplate Screw (E) holes on Mounting Plate (A) are positioned on the left and right.
3. Fasten Mounting Plate (A) to wall:
   • a. If fastening to a wall stud: Secure using (4) wood screws and a screwdriver.
   • b. If fastening to a hollow area: Mark the location to install plastic anchors. Drill 1/4” pilot holes on the marked spots and insert plastic anchors. Affix to anchors.
4. Place Backplate (D) against the wall, ensuring holes on each side of Backplate (D) align with the holes on Mounting Plate (A). Secure Backplate (D) to Mounting Plate (A) with Backplate Screws (E).
5. Insert Harp (H) into Socket Base (G) by squeezing legs together.
6. Install light bulb (not included).
7. Place Shade (I) on Harp (H) and secure using Finial (J).
8. Position Mounting Channel (K) on the wall between Backplate (D) and the floor.
   • Note: Both Cord Covers (L) snap onto (1) Mounting Channel (K).
9. Fasten Mounting Channel (K):
   • a. If fastening to a wall stud: Secure using (4) wood screws and a screwdriver.
   • b. If fastening to a hollow area: Mark the location to install plastic anchors. Drill 1/4” pilot holes on the marked spots and insert plastic anchors. Affix to anchors.
10. Place Power Cord (M) into Mounting Channel (K) and affix first Cord Cover (L over the upper half of Mounting Channel (K). Affix second Cord Cover (L) to the bottom half of the Mounting Channel (K). Note: If Cord Covers (L) do not snap into place, widen Mounting Channel (K) by gently pulling it apart.
11. Plug the Power Cord (M) into an outlet.

INSTALLATION INSTRUCTIONS – JUNCTION BOX

1. Unscrew Backplate Screws (E) to remove Mounting Plate (A) from Backplate (D).
2. Remove Power Cord (M):
   • a. Turn Wire Connectors (C) in a counter-clockwise direction to detach Power Cord (M) from fixture wires.
   • b. Undo the safety knot on Power Cord (M) and remove it from the bottom of Backplate (D).
3. Secure Mounting Plate (A) to the junction box (not included) using Mounting Screws (B) provided, ensuring the Backplate Screw (E) holes on Mounting Plate (A) are positioned on the left and right.
4. Using the wire graph below, connect the appropriate wires from the fixture to the corresponding wires in the electrical junction box (not included) and secure Wire Connectors (C).
   • A. Connect the ground wire (bare copper or green) from your fixture to the:
   • the ground wire in the junction box, or
   • ground screw in the junction box
   • B. Connect the BLACK house wire to fixture hot wire that corresponds to the diagram (black, round & smooth, white/grey with tracer, brown/gold without tracer).
   • C. Connect the WHITE house wire to fixture neutral wire that corresponds to the diagram (white, ribbed/ridged, white/grey without tracer, brown/gold with tracer).
5. Place all wires and Wire Connectors (C) back into the junction box.
6. Place Backplate (D) against the wall, ensuring Backplate Screws (E) are protruding through the holes in Backplate (D). Secure the fixture in place to the Mounting Plate (A) with Decorative Caps (F).
7. Insert Harp (H) into Socket Base (G) by squeezing legs together.
8. Place Shade (I) on Harp (H) and secure using Finial (J).
9. Install light bulb (not included).

HELPFUL TOOLS: Safety Goggles, Screwdriver, Ladder

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>