BIN WAREHOUSE 65001 8 Tote Storage Rack Instruction Manual
- October 30, 2023
- BIN WAREHOUSE
Table of Contents
Solutions Murales PROSLAT inc.
1 888 691-2944
Model # 65001
TOOLS REQUIRED
- Drill with #2 Phillips-Head Tip
-
2 Philips head Screwdriver
PARTS LIST
- 8 x Horizontal crossbars
- 2 x Center verticals
- 2 x Left & right rear corner verticals
- 1 x Left front corner vertical
- 1 x Right front corner vertical
- 4 x Wall mount flanges
- 4 x Wall mount extensions tubes
- 8 x Horizontal slide rails
FASTENER LIST
- 44 x #08 x 3/4 in. Fastening screws
- 8 x #08 x 1-½ in. Wall mount Extension tube fastening screws
- 12 x #10 x 1-½ in. Wall mount flange screws
- 12 x Plastic wall anchors
NOTE
HARDWARE IS LOCATED IN THE TUBES.
Separate all parts into groups (as shown) and familiarize. Read all
instructions before beginning assembly.
8 TOTE STORAGE RACK
Assembly instructions
FRONT GRID ASSEMBLY
| |
---|---|---
PARTS NEEDED:
4 of #1
1 of #2
1 of #4
1 of #5| STEP 1
4 Horizontal crossbars (#1) inserted through 1 Center Vertical (#2) Note:
Slide horizontal crossbar into left side of center vertical following
direction of arrow until alignment dimple
meets center vertical.| STEP 2
1 Left front corner vertical (#4) and 1 right front
corner vertical (#5) Placed on horizontal crossbar.
REAR GRID ASSEMBLY
| |
---|---|---
PARTS NEEDED:
4 of #1
1 of #2
2 of #3| STEP 1
4 Horizontal Crossbars (#1) inserted through 2 center vertical (#2) Note:
Slide horizontal crossbar into right side of center vertical following
direction of arrow until alignment dimple meets center vertical.| STEP 2
2 Left and right rear corner verticals (#3) placed
on horizontal crossbars.
SLIDE RAIL ASSEMBLY TO REAR GRID
| |
---|---|---
PARTS NEEDED
8 of #8| STEP 1
8 Horizontal slide rails (#8) inserted in rear grid.
Tip: If necessary, tap horizontal slide rails to be sure slide rails are fully
inserted.| STEP 2
Fastening horizontal slide rails (#8) in rear grid
using 8 – #08 x ¾ in. fastening screws (#1).
Note: Start at top row and work down.
Use only one fastener – bottom hole only.
JOINING FRONT TO REAR GRID
| |
---|---|---
STEP 1:
Insert bottom slide rails (#8) into front grid
assembly and fasten (making sure fully inserted)using 2 – #08 x ¾ in.
fastening screws (#1)
Note: Fasteners in bottom hole only| STEP 2:
Insert and fasten next 3 rows of slide rails to front grid using 6 – #08 x 3/4
in. fastening screws (#1) Note: Fasteners in bottom hole only.| STEP 3:
Turn unit upright and place firmly against wall where unit is to be mounted.
FASTENING VERTICALS AND WALL MOUNT TUBES
| |
---|---|---
STEP 1:
Fasten all verticals to horizontals. Make sure all joints are pressed firmly
together, tigh and against alignment dimples using 24 – #08 x ¾ in. fastening
screws (#1). Note: 1 fastener per joint, each grid, front side only| STEP
2:
Move unit away from wall and insert 4 wall mount extensions tubes (#7) in 4
locations. Fasten with 8 – #08 x 1-½ in. extension tube fastening screws (#2).
Note: 1 fastener per joint front side only.| STEP 3:
Slide wall mount flanges (#6) into wall mount tubes (#7). Place unit against
wall where it is to be mounted and mark wall flange holes. Note: Do NOT fasten
at this time. Make
sure unit remains in position at all 4 flange locations while marking holes.
FASTENING TO WALL
| |
---|---|---
Move unit away from wall and remove wall flange from tube and mount flange to
wall using 12 #10 x 1½ in. wall mount flange screws (#3) and plastic wall
anchors (#4) if needed. Note: If mounted into masonry or drywall, drill three
¼ in. holes to accept plastic wall anchors.| Slide unit back against wall
while inserting all 4 wall mount extension tubes (#7) into wall mount flanges
(#6) and fasten with 4 – #08 x ¾ in. fastening screws. (#1). Note: Use a
screwdriver, one screw per flange.| Unit must be attached to wall to keep from
tipping over!
Congratulations! We hope you enjoy your Bin Warehouse tote
storage rack!
Warranty – Bin Warehouse PVC Rack
This Lifetime Warranty extends only to the first retail purchaser of Proslat
Bin Warehouse product(s)
Lifetime Warranty.
This document details the Solutions Murales PROSLAT inc. Warranty for all new
Proslat Bin Warehouse product purchased anywhere in continental USA and
Canada. Solutions Murales PROSLAT inc. (hereafter Proslat) warrants its Bin
Warehouse Rack against defects in material or workmanship for a lifetime
period. Proslat will replace any defective Rack as long as it was installed
and maintained according to the printed instructions. Any Proslat Bin
Warehouse Rack replaced under the terms of the Lifetime Warranty inherits the
remaining warranty period from the original purchase.
Exclusions.
The Proslat Warranty does not cover the following: – Damage that results from
improper installation or misuse or abuse; – Damage due to acts of God, fire,
or accident; – Damage that results from loading the rack beyond the stated
maximum weight capacity; – The cost of labor or accessory materials; and
shipping cost to return defective products.
Limitations of Warranty.
The above Lifetime Warranty is the exclusive warranty for Proslat Bin
Warehouse product. Proslat disclaims all other warranties, express or implied,
including any implied warranties or merchantability, fitness for particular
purpose or otherwise. If you live in an area where consumer law prohibits this
disclaimer, the above Lifetime Warranty will not extend the time period of any
such implied warranty. Obtaining Lifetime Warranty Service. For warranty
service, call 1.888.691.2944. You will need your original proof of purchase
and photos to illustrate the claimed defect.
DISCLAIMER OF LIABILITY
Solutions Murales PROSLAT inc. and its successors, distributors and dealers
(hereafter SELLER) shall in no way be responsible for the product’s proper use
and service. THE BUYER HEREBY WAIVES ALL LIABILITY CLAIMS. The BUYER
acknowledges that he/she is not relying on the SELLER’s skill or judgment to
select or furnish goods suitable for any particular purpose and that there are
no liabilities which extend beyond the description on the face hereof and the
BUYER hereby waives all remedies or liabilities, expressed or implied, arising
by law or otherwise, (including without any obligations of the SELLER with
respect to merchantability and consequential damages) or whether or not
occasioned by the SELLER’s negligence. The SELLER disclaims any warranty and
expressly disclaims any liability for personal injury or damages. The BUYER
acknowledges and agrees that the disclaimer of any liability for personal
injury is a material term for this agreement and the BUYER agrees to indemnify
the SELLER and to hold the SELLER harmless from any claim related to the item
of the equipment purchased. Under no circumstances will the SELLER be liable
for any damages or expenses by reason of use or sale of any such equipment.
The SELLER assumes no liability regarding the improper installation or
misapplication of its products. It is the installer’s responsibility to check
for proper installation and if in doubt, contact the manufacturer. These
assembly guidelines will direct you through the process of assembling a
section of Solutions Murales PROSLAT inc. product. Please keep in mind that
they may not cover every assembly or installation scenario you may encounter.
Since each installation is unique in its performance requirements, the
ultimate installation method used is the sole responsibility of the installer.
Solutions Murales PROSLAT inc. disclaims any liability or responsibility for
the improper installation of this product. The purchaser is solely responsible
for compliance with applicable local codes. Solutions Murales PROSLAT inc.
recommends that all designs be reviewed by a licensed architect, engineer or
local building official before installation.
Questions, problems, missing parts? Before returning to the store, call
Proslat Customer Service — 8 a.m. – 5 p.m., EST, Monday – Friday
1-888-691-2944
info@proslat.com
www.proslat.com
Retain this manual for future use.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>