Altronix OLS200220 Off-Line Power Supply Charger Installation Guide

Altronix OLS200220 Off-Line Power Supply Charger

Overview

Altronix OLS200220 power supply/charger converts 220VAC (working range 198VAC- 256VAC), 50/60Hz input into a 12VDC at 10A of continuous supply current (see specifications). This general-purpose power supply has a wide range of applications for access control and security system accessories that require additional power.

Specifications

Input:

• 220VAC (working range 198VAC-256VAC), 50/60Hz, 0.95A.

Output:

• 12VDC output.
• 10A continuous supply current.
• Filtered and electronically regulated output.
• Short circuit and thermal overload protection.

Supervision:

• AC fail supervision (form “C” contacts).
• Low battery supervision (form “C” contacts).

Visual Indicators:

• AC input and DC output LED indicators.

Battery Backup:

• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when AC fails.
• Maximum charge current 0.7A.

Features:

• Power ON/OFF switch.
• Includes battery leads.

Board Dimensions (L x W x H approx.):

• 7.25” x 4.5” x 1.75” (184.1mm x 114.3mm x 44.5mm).

Installation Instructions

OLS200220 should be installed in accordance with The National Electrical Code and all applicable Local Regulations.

1. Mount the OLS200220 in the desired location/enclosure (mounting hardware included).

2. Slide [Power ON/OFF] switch to the OFF position (Fig. 1, pg. 2).

3. Connect AC power to the terminals marked [L & N], and connect ground to the terminal marked [G]. Use 18 AWG or larger for all power connections (Battery, DC output, AC input).
   Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting). Keep power-limited wiring separate from non-power-limited wiring (220VAC, 50/60Hz Input, Battery Wires). Minimum 0.25” spacing must be provided.
   CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment. There are no user-serviceable parts inside. Refer installation and servicing to qualified service personnel.

4. Slide [Power ON/OFF] switch to the ON position (Fig. 1, pg. 2).

5. Measure output voltage before connecting devices. This helps avoid potential damage.

6. Slide [Power ON/OFF] switch to the OFF position (Fig. 1, pg. 2).

7. Connect devices to be powered to the terminals marked [– DC +]. When the use of stand-by batteries is desired, they must be lead acid or gel type.

8. Connect the battery to the terminals marked [– BAT +] (battery leads included).
   Note: When batteries are not used, a loss of AC will result in the loss of output voltage.

9. Connect appropriate signaling notification devices to AC Fail & Low battery supervisory relay outputs marked [NC, C, NO].

10. Slide [Power ON/OFF] switch to ON position (Fig. 1, pg. 2).

LED Diagnostics

Terminal Identification

ground.
– DC +| 12VDC @ 10A continuous supply current.
AC FAIL

NC, C, NO

| Used to notify loss of AC power, e.g. connect to audible device or alarm panel. Relay normally energized when AC power is present. Contact rating 1A @ 28VDC.
Low Battery NC, C, NO| Used to indicate low battery condition, e.g. connect to alarm panel.

Relay normally energized when DC power is present. Contact rating 1A @ 28VDC Low battery threshold: 12VDC output threshold set @ approximately 10.5VDC.

– BAT +| Stand-by battery connections. Maximum charge rate 0.7A.

Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056. website: www.altronix.com
e-mail: info@altronix.com | Lifetime Warranty IIOLS200220 – Rev. 060210 H31U.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>