Bathroom Sink OVS-0382Y 1.28 GPF One Piece Toilet Instruction Manual
- October 30, 2023
- Bathroom Sink
Table of Contents
Sink OVS-0382Y 1.28 GPF One Piece Toilet
Instruction Manual INSTALLATION INSTRUCTIONS
MODERN 1.28 GPF ONE PIECE TOILET
Model OVS-0382Y
Complies with ASME A112.19.2/CSA B125.1-2013.
OVS-0382Y 1.28 GPF One Piece Toilet
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Hacksaw
Regular Screwdriver
Wax Ring/Gasket
Adjustable Wrench| Flexible Supply Tube
Sealant
Closet Bolts
Tape Measure
Carpenters Level
---|---
1. REMOVE OLD TOILET (IF NEW INSTALLATION PROCEED TO STEP 2)
a. Close toilet supply valve and flush tank completely. Towel or sponge
remaining water from tank and bowl.
b. Disconnect and remove supply line.
NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to
prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from
base area.
NOTE: Mounting surface must be clean and level before new toilet is
installed!
| 
---|---
DIMENSIONS (Nominal)
NOTE: Distance from wall to closet flange centerline (rough-in) must be
12″ (305 mm) minimum.| INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 901, and slide into place 6″ (152
mm) apart and parallel to wall.
| 
INSTALL WAX RING
Invert toilet on floor (cushion to prevent damage), and install wax ring
evenly around waste flange (horn), with tapered end of ring facing toilet.
Apply a thin bead of sealant around base flange.| INSTALL TOILET ON
FLANGE
a. Remove waste covering and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. (Larger diameter side of washers
(Marked “THIS SIDE UP”) must face up!)
| 
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion, press bowl
down fully on wax ring and flange. Alternately tighten nuts until toilet is
firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If needed, cut bolt height to size before
installing caps.) Place a bead of sealant around base. Remove excess sealant.
c. Smooth off the bead of sealant around base. Remove excess sealant.|
CONNECT WATER SUPPLY
a. Connect water supply line between shutoff valve and tank water inlet
fitting. Tighten coupling nuts securely.
b. Turn on supply valve and allow tank to fill until float rises to shutoff
position.
c. Check for leakage at fittings, tighten or correct as needed.
8. INSTALL TOILET SEAT
Install toilet seat in accordance with enclosed directions.
SAVE FOR FUTURE USE
Documents / Resources
|
Bathroom Sink OVS-0382Y 1.28 GPF One Piece
Toilet
[pdf] Instruction Manual
TM-0382Y-JM, 774980150702, 0774980150702, 1008016443, OVS-0382Y 1.28 GPF One
Piece Toilet, OVS-0382Y, OVS-0382Y GPF One Piece Toilet, 1.28 GPF One Piece
Toilet, GPF One Piece Toilet, 1.28 One Piece Toilet, One Piece Toilet, Toilet
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>