M MARANTEC ‎M13-631 WIRELESS KEYLESS ENTRY USER INSTRUCTIONS

M MARANTEC ‎M13-631 WIRELESS KEYLESS ENTRY

WIRELESS KEYLESS ENTRY

MODEL M13-631

The Wireless Keyless Entry System offers you the convenience of opening and closing your garage door by entering your own 4-digit Personal Identification Number (PIN) via the keypad. The WKE can be programmed wirelessly to control up to 4 garage door operators that each work on a different code, or to control one garage door operator with up to 4 different PINs. You can also program it to allow a temporary PIN of your choice to be stored, to provide temporary access to authorized visitors or service persons. Check the box content to familiarize yourself with the parts shown in Fig.1 and 2.

Other Features Include:
Wireless Installation, Wireless Programming, Low Battery Indication, One- Button-to-Close Operation, Backlit Keypad, Code Security, Anti-Tampering, and Weather-Resistant Design.

WARRANTY

Limited Warranty 1 Year

Warning

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

• Install Wireless Keyless Entry System within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5m) and away from ALL moving parts of the door. ALWAYS keep remote controls out of reach of children. NEVER permit children to
• operate, or play with remote controls.
• Activate the gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
• ALWAYS keep the gate or garage door in sight until completely closed. NEVER permit anyone to cross the path of a moving gate or door.

PROGRAM PIN AND TRANSFER TRANSMITTER CODE

1. Install batteries provided, see Fig. 2.
   Press and hold the button for at least 3 seconds to activate programming mode, LEDs light up for 10 seconds.

2. Hold the transmitter very close to the keypad buttons and Press and hold the transmitter button you use to open and close your garage door. Release the transmitter button when the LED on the keypad flash.

3. Enter a 4-digit personal identification number (PIN) of your choice # # # #.

4. Press and release the ENTER button.
   LEDs and keypad buttons will light up for 2 seconds signaling programming is completed.

5. Test WKE by entering the PIN, then press ENTER button.

NOTE: To program the WKE to more than one garage door operator (maximum 4), repeat the steps above using a new PIN for each additional garage door operator.

CHANGE AN EXISTING PIN

1. Press the button for at least 3 seconds, and LEDs will flash slowly. Release button.
2. Enter the programmed PIN that you want to change. Press the ENTER button. LEDs will flash rapidly.
3. Enter the new 4-digit PIN of your choice # # # # then press the ENTER button. LEDs and keypad light up for 2 seconds.
4. To test WKE, enter the new PIN then press the ENTER button. The garage door opener will activate.

PROGRAM A TEMPORARY PIN

A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary PIN. The temporary PIN can be set for a number of door openings (max 99). The temporary PIN cannot be the same as any previously programmed PIN.

1. Press the button for at least 3 seconds. LEDs will flash slowly for 10 seconds. NOTE: To successfully establish a temporary pin, steps 2-4 must be completed within 10 seconds after programming activation.
2. Enter any programmed PIN, then press ENTER button. LEDs will flash rapidly.
3. Enter the temporary 4-digit PIN of your choice # # # # then press the ENTER button. LEDs will flash very rapidly.
4. Press the number of openings the temporary PIN will work (up to 99). Then press the ENTER button. LEDs and keypad buttons light up for 2 seconds then the system goes into standby mode.

To test, enter the temporary PIN, then press the ENTER button. The garage door operator will activate. If the temporary PIN was set for a number of openings, the test will use up one opening programmed PIN.

NOTE: To clear the temporary PIN, repeat steps 1-3 above, setting the number of openings to “0” in step 4.

INSTALLATION

1. Select a location to mount the Keyless Entry at a minimum height of 5 feet (1.5m) out of the reach of children.
2. Use the mounting plate as a template, mark the hole location, and then drill two 1/8 inch (3.2mm) pilot holes.
3. Secure the plate to the mounting surface with the (2) screws provided. Do not over-tighten screws to avoid cracking the plastic.
4. Cover batteries with battery cover.
5. Snap WKE into the mounting plate and secure it with the screw provided. See Fig. 1.
6. Install the slide-up protective cover. Align cover slides with slide grooves on WKE and slide the cover down until it locks.

OPERATION

The garage door operator activates when the PIN and ENTER buttons are pressed. The keypad will blink for 28 seconds, during that time the ENTER button can be used to stop, start, and reverse the door.
If the wrong number is accidentally pressed, press the correct PIN and then the ENTER button. The Keyless Entry will transmit only the last four digits.

ONE-BUTTON-TO-CLOSE: The Keyless Entry has a feature that allows the door to be closed using the ENTER button instead of a PIN.

NOTE: Factory setting active.

To deactivate the one-button close feature:

1. Press the button for 3 seconds. LED on the keypad flashes slowly.
2. Press the ENTER button.
3. The keypad LEDs light up for 2 seconds indicating that the one-button close feature has been deactivated.

To activate the one-button close feature:

1. Press the button for 3 seconds. LED on the keypad flashes slowly.
2. Press the ENTER button.
3. The keypad LEDs light up for 2 seconds indicating that the one-button close feature has been activated.

CLEARING WKE Memory

1. Remove Wireless Keyless from the wall mounting plate. Remove batteries from Wireless Keyless.
2. Press and hold ENTER button.
3. Install batteries back. Match polarity designation.
4. Release ENTER button, the LED flashes rapidly approximately 5 seconds.

BATTERY

Warning

To prevent possible SERIOUS INJURY or DEATH: NEVER allow small children near batteries. If the battery is swallowed, immediately notify a doctor.

Low Battery Indicator:
Replace the batteries when all the keypad buttons start to flashed buttons start to flash (10 seconds) upon r(10 seconds) upon raising the Wireless KWireless Keyless protective coverless protective cover.

REPLACEMENT PARTS

• Battery – AAA (Qty 2)
• Keypad cover – (Call customer service)

FCC and IC Certified

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.

FREQUENTLY ASKED QUESTIONS

What is the M MARANTEC ‎M13-631 Wireless Keyless Entry?

The M MARANTEC ‎M13-631 is a wireless keyless entry system used to control and operate Marantec garage door openers.

How does the M MARANTEC ‎M13-631 Wireless Keyless Entry work?

The M MARANTEC ‎M13-631 Wireless Keyless Entry uses a secure wireless signal to communicate with the compatible Marantec garage door opener, allowing you to open and close the garage door by entering a unique PIN code.

Can the M MARANTEC ‎M13-631 Wireless Keyless Entry be programmed to multiple garage door openers?

Yes, the M MARANTEC ‎M13-631 Wireless Keyless Entry can be programmed to work with multiple Marantec garage door openers.

How many PIN codes can be programmed into the M MARANTEC ‎M13-631 Wireless Keyless Entry?

The M MARANTEC ‎M13-631 Wireless Keyless Entry can typically store multiple PIN codes, allowing each user to have their unique access code.

Is the M MARANTEC ‎M13-631 Wireless Keyless Entry weatherproof?

Yes, the M MARANTEC ‎M13-631 Wireless Keyless Entry is designed to be weatherproof and can withstand various weather conditions.

Does the M MARANTEC ‎M13-631 Wireless Keyless Entry require batteries?

Yes, the M MARANTEC ‎M13-631 Wireless Keyless Entry is battery-operated and requires standard batteries (usually AAA) for power.

How do I change the PIN code on the M MARANTEC ‎M13-631 Wireless Keyless Entry?

To change the PIN code on the M MARANTEC ‎M13-631 Wireless Keyless Entry, you need to follow the programming instructions provided by Marantec. These instructions are typically included with the product or can be found in the user manual.

Can I use the M MARANTEC ‎M13-631 Wireless Keyless Entry with a Marantec garage door opener that has rolling code technology?

Yes, the M MARANTEC ‎M13-631 Wireless Keyless Entry is compatible with Marantec garage door openers that use rolling code technology, which provides enhanced security.

Can the M MARANTEC ‎M13-631 Wireless Keyless Entry be installed on any garage door?

The M MARANTEC ‎M13-631 Wireless Keyless Entry is designed to work specifically with Marantec garage door openers. It may not be compatible with other brands or models of garage doors.

Does the M MARANTEC ‎M13-631 Wireless Keyless Entry have a backlight for nighttime use?

Yes, the M MARANTEC ‎M13-631 Wireless Keyless Entry often features a backlit keypad, making it easier to enter the PIN code in low-light or nighttime conditions.

Is the M MARANTEC ‎M13-631 Wireless Keyless Entry compatible with older Marantec garage door opener models?

The M MARANTEC ‎M13-631 Wireless Keyless Entry is generally compatible with a wide range of Marantec garage door opener models. However, it's recommended to check the compatibility with your specific model.

Can the M MARANTEC ‎M13-631 Wireless Keyless Entry be used to operate other devices besides garage door openers?

No, the M MARANTEC ‎M13-631 Wireless Keyless Entry is specifically designed for use with Marantec garage door openers and may not work with other devices.

Does the M MARANTEC ‎M13-631 Wireless Keyless Entry have a time-limited access feature?

Some versions of the M MARANTEC ‎M13-631 Wireless Keyless Entry may offer a time-limited access feature, allowing you to set specific time windows during which the entered PIN code is valid.

Can the M MARANTEC ‎M13-631 Wireless Keyless Entry be installed on a gate or entrance other than a garage door?

While the M MARANTEC ‎M13-631 Wireless Keyless Entry is primarily designed for garage doors, it may be possible to install it on other gates or entrances if they are compatible with Marantec systems.

Is the M MARANTEC ‎M13-631 Wireless Keyless Entry compatible with home automation systems?

The M MARANTEC ‎M13-631 Wireless Keyless Entry is typically not designed to integrate with home automation systems. It functions as a standalone device for controlling Marantec garage door openers.

DOWNLOAD THE PDF LINK:M MARANTEC ‎M13-631 WIRELESS KEYLESS ENTRY USER INSTRUCTIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>