Torque XTTM1-RPH-102 TANK M1 Push Sled Installation Guide

: October 30, 2023
: Torque

Table of Contents

TOOLS NEEDED FOR ASSEMBLY
Assembly Instruction
TANK M1 RESISTANCE ADJUSTMENT
TANK M1 PUSH/PULL BAR ADJUSTMENT
TANK OPERATION
V-STRAP ATTACHMENT (OPTIONAL)
TOW ROPE ATTACHMENT (OPTIONAL)
WHEELBARROW HANDLE ATTACHMENT (OPTIONAL)
INSPECTION & LUBRICATION
SHROUD REMOVAL
SHROUD REMOVAL
CHAIN ADJUSTMENT
IMPORTANT SAFETY INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Torque XTTM1-RPH-102 TANK M1 Push Sled Installation Guide

ITEM	PART NUMBER	DESCRIPTION	QTY
1	5818101	ASSY, CHASSIS-M1	1
2	5661501	ASSY, REAR FRAME	1
3	2024401	WASHER, 8.4MM X 16MM X 1.8MM CLEAR ZINC	8
4	2009801	SCREW, M8-1.25 X 20L SOC HD GR 12.9	8
5	2010801	WASHER, STEEL 12.7 ID-25 OD-2 THK CLEAR ZINC	2
6	5654501	ASSY, REAR WHEEL 10″ DIA X 3″ WIDE	2
7	2010901	WASHER, LOCK M12 SAE ST ZN	2
8	2011301	SCREW, M12-1.75 X 30L SOC HD GR 12.9 CLEAR ZINC	2
9	56930PA	PTD ASSY, RH PUSH HANDLE	1
10	56931PA	PTD ASSY, LH PUSH HANDLE	1

NOTE:
Items 11-19 not included.

To discover what accessories pair well with the TANK M1, visit our web site at:
www.torquefitness.com/collections/tank- accessories. or by phone at 877-767-78

TOOLS NEEDED FOR ASSEMBLY

10MM ALLEN WRENCH (INCLUDED)
6MM ALLEN WRENCH (INCLUDED)
AIR PUMP WITH GAUGE
PHILLIPS SCREW DRIVER

Assembly Instruction

STEP 1
Assembly Instruction

NOTE:

LOOSELY tighten bolt connections in this step
Assembly Instruction

STEP 2
Assembly Instruction
NOTE:
SECURELY tighten all bolt connections in this step and previous step

STEP 3
Assembly Instruction

TANK M1 RESISTANCE ADJUSTMENT

POSITION N: NEUTRAL
POSITION 1: LOW RESISTANCE
POSITION 2: MEDIUM RESISTANCE
POSITION 3: HARD RESISTANCE

TANK M1 PUSH/PULL BAR ADJUSTMENT

Assembly Instruction

TANK OPERATION

Tank Operation

NOTE:
Weight plates are not included. Weight plates are only needed to prevent skidding and lifting of the back wheels. Adding weight does not affect the resistance

V-STRAP ATTACHMENT (OPTIONAL)

Tank Operation

NOTE:
Weight plates are not included. Weight plates are only needed to prevent skidding and lifting of the back wheels. Adding weight does not affect the resistance

To discover what accessories pair well with the TANK M1, visit our web site at: www.torquefitness.com/collections/tank- accessories. or by phone at 877-767-7835

TOW ROPE ATTACHMENT (OPTIONAL)

Tank Operation

WHEELBARROW HANDLE ATTACHMENT (OPTIONAL)

Assembly Instruction

XTM1-WMSS WALL MOUNT STORAGE SYSTEM (OPTIONAL)

Assembly Instruction

NOTES:
The images above show the anchoring hardware used for attaching to typical walls with wood studs spaced 16″ on center. The anchors used will depend on the wall construction. NOTE: At least four anchoring locations must be used in each part. The pull-out strength of the anchoring bolts used must be greater than or equal to 200 lbs. (91 kg)

SECURELY tighten bolt connections in this step

WARNING:
The UPPER MOUNT MUST be anchored to the wall using four WALL ANCHORS suitable for that particular wall construction
Assembly Instruction

WARNING:
The LOWER MOUNT MUST be anchored to the wall using four WALL ANCHORS suitable for that particular wall constuction

XTM1-WMSS WALL MOUNT STORAGE SYSTEM (OPTIONAL) M1 STORAGE

XTM1-WMSS WALL MOUNT STORAGE SYSTEM (OPTIONAL) PUSH HANDLE STORAGE

CONSOLE, TANK M1 (OPTIONAL)
Assembly Instruction

INSPECTION & LUBRICATION

INSPECTION:

ATTENTION:
PLEASE ENSURE THAT ALL TIRES ARE INFLATED TO 30 PSI. FAILURE TO DO SO MAY RESULT IN TANK VEERING DURING USE.

Once a month, check for loose bolts on frame and wheels. Tighten if necessary.

Once a month, remove shroud as shown on PAGE 18 and check that the chain and sprockets are clean, free of rust, dust and grime. Make sure that the chain is properly lubricated.

If chain ever becomes loose, see PAGE 19 to adjust chain.

Once a month, check tire pressure and inflate if needed

LUBRICATION:

Once a month, the sprockets should be cleaned and the chain should be lubricated.

RECOMMENDED LUBRICATION: Use a Dry lubrication for indoor use, and wet lubrication for outdoor use. Most bicycle shops carry a variety of different lubricants and can recommend a lubricant based on the conditions where the TANK will be used.

#TorqueFitness #TorqueTANK
https://www.instagram.com/torquefitnessusa/
https://www.youtube.com/c/TorqueFitness
https://www.facebook.com/groups/thetankcommunity

SHROUD REMOVAL

Assembly Instruction

SHROUD REMOVAL

BOTTOM VIEW
Assembly Instruction

CHAIN ADJUSTMENT

TO SET THE CORRECT CHAIN TENSION FOLLOW THESE STEPS:

TIP M1 BACK SO THAT IT RESTS ON THE REAR WHEELS AND PUSH HANDLES. AS SHOWN.
LOOSEN ALL FOUR BOLTS ONE FULL TURN EACH. (BOLT SHOULD BE LOOSE ENOUGH TO ALLOW THE BRAKE MODULE TO MOVE). ALLOW GRAVITY TO PULL THE BRAKE MODULE DOWNWARD REMOVING THE EXCESS SLACK.
SECURELY RE-TIGHTEN THE FOUR BOLTS.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: The safety of this product can be maintained only if it is examined regularly for damage and wear. See inspection and lubrication section on page 13 for more details.

DO NOT overinflate tires! All tires should be inflated to 30 PSI. Check air pressure periodically.
Keep children away from the TANK M1 during use.
Keep all loose clothing, hair and shoelaces away from moving parts.
DO NOT attempt to use the TANK M1 for any purposes other than that for which it was intended.
Wear shoes with rubber or high-traction soles. High heels, dress shoes, sandals or bare feet are not suitable for use with the TANK M1.
DO NOT drop the front wheel down when turning the TANK M1 around. Carefully set the front wheel down – especially with weight plates on the weight horn.
DO NOT place more than 135 LBS. on the weight horn of the TANK M1.
DO NOT drop the weight plates onto the TANK M1. Doing so, may result in damage to the TANK M1.
DO NOT use the TANK M1 in wet or slippery conditions.
DO NOT push the TANK M1 while any accessories are attached to the push/pull bar.
DO NOT stand or ride on the TANK M1.
DO NOT use the TANK M1 without the shroud.