Baxenden 900mm Grey Freestanding Vanity Unit with Basin User Manual
- October 30, 2023
- Baxenden
Table of Contents
INSTALLATION MANUAL
Non-Illuminated Bathroom Mirror
and Furniture
Thank you for choosing a Better Bathrooms Product
Please read this user manual before installing and using this product
Keep it safe for future reference.
Visit our page www.betterbathrooms.com/for
our entire range of Mirrors and Furniture
INSTALLATION TOOLS
PARTS LIST
Product| Description| Qty| Description| Qty|
Description| Qty| Description| Qty| Description|
Qty| Description| Qty| Description| Qty
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
24975
24976
24977| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| Round door
handle| 2| Round handle
screw| 2| Shell Door
Handle| 2| Shell Handle
Screw| 4
24978
24979
24980| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| Round door
handle| 2| Round handle
screw| 2| Shell Door
Handle| 2| Shell Handle
Screw| 4
24981
24982
24983| Wall Screw| 2| Wall Plug| 2| Brass washer| 2| Plastic washer| 2| Screw
Cap| 2| | | |
24984
24985
24986| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| Round door
handle| 2| Round handle
screw| 2| | | |
25008
25W9
25010| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| | | | | | | |
25011
25012
25013| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| | | | | | | |
25014
25015
25016| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| | | | | | | |
25017
25018
25019| Wall Screw| 2| Wall Plug| 2| Brass washer| 2| Plastic washer| 2| Screw
Cap| 2| | | |
2582625827
2582825829
2583025831
2583225833| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| Frame Screw| 12| | |
| | |
25841
25842
25843| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| | | | | | | |
25838
25839
25840| Wall Screw| 6| Wall Plug| 6| Wall Bracket| 2| Round door
handle| 1| Round handle
screw| 1| Shell Door
Handle| 1| Shell Handle
Screw| 2
26938
26939
26940| Wall Screw| 2| Wall Plug| 2| Brass Washer| 2| Plastic Washer| 2| Screw
Cap| 2| | | |
27465
27466
27799| Wall Screw| 2| Wall Plug| 2| Brass washer| 2| Plastic washer| 2| Screw
Cap| 2| | | |
INSTALLATION
Check the product for damage prior to installation
Before any drilling is carried out, please check for pipes and wires within
the wall which could be damaged.
MIRROR INSTALLATION
Fitted to the rear of the unit are x 2 fixing brackets, measure the distance
between the two brackets and mark this distance on the wall, ensuring this
horizontally aligned, using a spirit level.
We recommend a height for the brackets of 70″ (1778mm) from the floor, but
this is customer choice.
It is recommended to install to a solid wall, but if fitting to a stud wall,
the fixings must be secured into a stud, not only into the plasterboard.
MIRROR INSTALLATION
After the position of the brackets is marked, drill the holes in the wall,
using an 8mm drill bit (not supplied), to a depth of approx 40mm.
Insert the wall plugs and tap flush with the wall surface.
MIRROR INSTALLATION
Hold the bracket up to the wall over the drilled holes and secure using the
screws provided.
Ensure the brackets on the rear
of the unit are fully tightened.
Lift the product on the wall mounted brackets to engage both sections of the
brackets.
Once installed a bead of silicone can be applied around the edges of the unit if required.
CABINET INSTALLATION
Fitted to the rear of the unit are x 2 fixing brackets, measure the distance
between the two brackets and mark this distance on the wall, ensuring this
horizontally aligned, using a spirit level.
We recommend a height for the brackets of 27.5″ (698mm) from the floor, but
this is customer choice.
It is recommended to install to a solid wall, but if fitting to a stud wall,
the fixings must be secured into a stud, not only into the plasterboard.
It is also recommended to set up the unit before installing the basin not the
unit, so any adjustment can be made, via the fixings on the unit.
CABINET INSTALLATION
After the position of the brackets is marked, drill the holes in the wall,
using an 8mm drill bit (not supplied), to a depth of approx 40mm.
Insert the wall plugs and tap
flush with the wall surface and secure the wall brackets into place.
CABINET INSTALLATION
Check the brackets fitted to the unit are fully tightened. Lift the unit onto
wall fitted brackets.
If any adjustment forward or
backward / up or down is required this is possible via the fitted adjusters on
the inside of the unit.
CABINET INSTALLATION
After any adjustment of the unit has been made the basin can be fitted to the
unit, by applying a bead of silicone between the unit and basin to provide a
seal and fixing for the basin to the unit.
Also run a bead of silicone along the back edge of the base where it meets the
wall.
DOOR HANDLE INSTALLATION
The doors which are to be fitted with handles, either the round or shell type
are provided with pilot holes which should be drilled to allow fitting of the
handle screw through the door and into the handle.
Drill the holes, then place the screw through the unit from inside the door,
connect this to the handle and tighten
FRAMED FURNITURE ASSEMBLY
Place the frame onto the unit and screw the frame to the unit through the
holes in the frame, ensuring this is aligned with the unit edge.
Ensure this is fully secured before use
WC UNIT INSTALLATION
Drill into the wall through the rear plinth of the WC unit.
Fit the wall plug
Place the screw through the washers and secure to the wall.
Fit brass screw cap to brass washer
Measure the height from the floor to height a then measure height b and allow 5mm tolerance, then measure width c and allow 5mm
Mark these dimensions on to the front panel of the unit using a pencil
Remove the front panel from the unit and cut the hole to allow the waste pipe and flush pipe to pass from the cistern
It is recommended to seal the
cut edge and bottom edge of the unit, to protect against moisture ingress
CLEANING AND MAINTENANCE
Wipe the product clean and dry regularly, especially when the product is
subject to steam or splashes.
Do not use harsh chemicals or materials on the product, as this will damage
the product and invalidate your guarantee.
To clean and maintain the product, wipe using a clean damp cloth and wipe dry
with a soft cloth.
We hope your new product goes above and beyond your expectations. However,
should any problems occur, please:
- log in to your account and contact our customer services team via your self-serve portal — betterbathrooms.com/CustomerAccount/Login
- contact us via betterbathrooms.com/content/contact-us
Vanity Basin
Please note: Image is for illustrative purposes only and may differ slightly to the actual product
- Single-person assembly
- Tools required
- We always recommend using professional tradespeople to install your product
V3_12.10.21
Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We’re on a mission to bring you extraordinary bathroom products, for less.
From modern to traditional style ceramics, plus the gorgeous fixtures,
fittings and furniture to match. So, you can fall in love with your space
every single day.
As one of the UK’s largest independent bathroom stores, we’ve received
countless awards; including the National Business Awards UK, the Digital
Entrepreneur Awards and being placed on The Sunday Times Fast Track 100.
We hope your new product goes above and beyond your expectations. However,
should any problems occur, please:
- log in to your account and contact our customer services team via your self-serve portal – betterbathrooms.com/CustomerAccount/Login
- contact us via betterbathrooms.com/content/contact-us
Important information
- Please read these instructions thoroughly and retain for future reference
- Always check for pipes and cables before drilling
Contents
- Basin x 1
Tools required
Silicone, Drill ,Spanner
Installation
-
Check the wall for pipes and wires before drilling, drill through the back plinth into the wall in the desired location, ensuring the unit is level
-
Secure the unit to the wall using a suitable wall fixing for your wall type (fixings not supplied with unit) ie plug and screw for solid walls
On receipt of the product
check for damage prior to commencement of any installation. Damage notified
after or during installation will be deemed as installation damage -
Apply a bead of silicone between the basin and the unit Place the basin/top onto the unit, again ensuring all parts are level Also apply silicone at any join between the basin and walls
-
It is recommended to silicone around the base of the unit, to prevent water from passing between the unit and the floor
Leave all silicone to dry for
at least 24 hours before use
Maintenance
The basin and any chrome components should be cleaned using a soft damp cloth,
no abrasive cleaning agents or materials should be used, as this can affect
the surface finish.
Use of any abrasives can invalidate your guarantee.
Cleaning
To maintain the surface finish of your product. wipe clean after every use. using a clean damp cloth, a mild detergent mixture can be used. Do not use abrasive cleaning agents or materials which can strip and scratch the surface, the use of these agents or materials can invalidate your guarantee.
DRAWER REMOVAL & INSTALLATION
Part of the BuyltDirect Group
For more information
• visit betterbathrooms.com
• email
[email protected]
• call 0330 390 3062
• write to Trident Business Park, Neptune Way, Huddersfield, HD21UA