ZIPPITY ZP19072 Portable Puppy Slatted Panel Flat-Top WoodTek Vinyl Fence Kit Instruction Manual

October 30, 2023
ZIPPITY

ZIPPITY ZP19072 Portable Puppy Slatted Panel Flat-Top WoodTek Vinyl Fence Kit Instruction Manual
ZIPPITY ZP19072 Portable Puppy Slatted Panel Flat-Top WoodTek Vinyl Fence
Kit

GENERAL INFORMATION

IMPORTANT

  • Check the inside of the larger pieces in your box for other materials packed inside.
  • When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
  • We recommend an area approximately 5’x 8’ for unobstructed assembling.
  • You should not need to use excessive force when assembling components.

Detail Product Dimmensions & Specifications

Detail Product Dimmensions & Specifications

INSPECT PARTS

STEP 1

  • Check the inside of the larger pieces in your box for other materials packed inside.

LAY OUT MATERIALS

  • **Rail End Cap (8) (4 Installed, 4 Loose)

**

  • **Portable Feet (4) ⅞” x 1½” x 12″

**

  • **Silicone No-Scratch Pad (8)

**

  • Top Rail (2) 1½” x 1½” x 44″
    LAY OUT MATERIALS

  • Bottom Rail (2) 1½” x 1½” x 44″
    LAY OUT MATERIALS

  • **Post (4) ⅞” x 1½” x 221/4”

**

  • **Center Support (2) 5/8” x 1” x 211/4”

**

  • **Slats (18) ¼” x 1¼” x 427/8

**

  • Connector Pin (4)

  • **Locking Pin (4)

**

  • **¾” Self-Drilling Stainless Steel Screw (16)


  • **1½” Self-Drilling Stainless Steel Screw (8)

**

ASSEMBLE FIRST PANEL

STEP 1

  • Slide (9) Slats (H) into the routed holes of the Center Support (G) until the center support sits in the middle of the slats
    ASSEMBLE FIRST PANEL

STEP 2

  1. Slide the slats into the routed holes in one of the Posts (F).
  2. Slide a second end post over the slats.
    ASSEMBLE FIRST PANEL

STEP 3

  1. Identify the Top Rail (D) and the Bottom Rail (E) as shown below.
  2. Insert two loose Rail End Caps (A). Make sure they are oriented as illustrated.
    ASSEMBLE FIRST PANEL

STEP 4

  1. Slide the top rail over the tops of the posts until the pre-drilled holes in the posts and the top rail align.
  2. Drive (2) total 3/4”Self-Drilling Stainless Steel Screws (K) into the pre-drilled holes in the top rail.
    ASSEMBLE FIRST PANEL

STEP 5

  1. Slide the bottom rail over the bottoms of the posts until the pre-drilled holes in the (2) posts and the bottom rail align. Ensure the middle post inserts into the hole in the bottom rail.
  2. Drive (2) total 3/4” self-drilling stainless steel screws into the pre-drilled holes in the bottom rail.
    ASSEMBLE FIRST PANEL

STEP 6

  • Turn the panel to the other side and drive (4) total 3/4” self-drilling stainless steel screws through the pre-drilled holes in the top and bottom rail.
    ASSEMBLE FIRST PANEL

ATTACH THE FEET

STEP 1

  1. Identify the Portable Feet (B). Set aside (4) of the Silicone No-Scratch Pads (C).
  2. Remove the adhesive cover from the pads and stick two pads on the far ends of the underside of each foot as shown below.
    ATTACH THE FEET

STEP 2

  1. Take one of the portable feet and slide the notched end over the underside of the bottom rail.
  2. Align the foot pre-drilled holes with the bottom rail pre-drilled holes and drive (2) 1½” Self Drilling Stainless Steel Screws (L) through the pre-drilled holes in the underside of the portable foot.
  3. Repeat this process on the other side of the fence panel.
    ATTACH THE FEET

ASSEMBLE SECOND FENCE PANEL

STEP 1

  • Repeat steps 3-4 to assemble the second fence panel
    ASSEMBLE SECOND FENCE PANEL

CONNECT THE PANELS

STEP 1

  • Connect the two fence panels using the Connector Pins (I) as shown below.
    In-Line Application:
    CONNECT THE PANELS

STEP 2

  • Connect the two fence panels using the Connector Pins (I) as shown below.
    Corner/Angled Application:
    CONNECT THE PANELS

STEP 3

  • Secure the connector pins with the Locking Pin (J).
    CONNECT THE PANELS

MISSING OR DAMAGED PARTS?

VISIT OUR WEBSITE FIRST, SO WE CAN HELP YOU RIGHT AWAY!

Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur. If you discover any missing, damaged, or defective parts, please visit our website to order replacement parts. If you experience any further trouble with your product, please contact our customer service department.

6935 Reames Rd. Ste. K. Charlotte, NC 28216

parts.nychbrands.com

support@zippity-outdoor.com

704-892-5222 / 877-234-6196

Customer service agents are available to take calls weekdays from 9am5pm EST. If you call outside of business hours, please leave a voicemail.

To help you quickly and accurately, please have reference item number ZP19072/ZP19073 and the specific part name which  can be found on page 5. It is helpful if you can provide the batch lot which is a stamped number inside the box.

NEED ASSEMBLY HELP?

If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so please give us a call at 704-892-5222 / 877-234-6196.

NEED TO RETURN?

If for some reason you need to return this product, please allow us to help resolve your issues first. If you still decide to return the product, you will need to initiate the return from the company you originally purchased from.

ZIPPITY logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals