ZIPPITY ZP19011 Surface Mounts Vinyl Fence Instruction Manual
- October 30, 2023
- ZIPPITY
Table of Contents
ZP19011 Surface Mounts Vinyl Fence
Instruction Manual
ZP19011 Surface Mounts Vinyl Fence
ZIPPITY
GALVANIZED STEEL AND VINYL SURFACE MOUNT 2-PACK
(30” H X 3 1/4” W)
60 MIN
Approximate assembly time
Want to see a video on how to assemble this product?
Scan the QR code https://zippity-outdoor.com/QR/ZP19011
GENERAL INFORMATION
IMPORTANT
Check the inside of the larger pieces in your box for other materials packed
inside.
When assembling components, place on a non-abrasive surface (i.e. shipping
box) to avoid scratching.
We recommend an area approximately 5’x 8’ for unobstructed assembling.
You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
VISIT OUR WEBSITE FIRST, SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of
this product, occasionally problems occur. If you discover any missing,
damaged or defective parts, please visit our website to order replacement
parts. If you experience any further trouble with your product, please contact
our customer service department.
parts.nychbrands.com
support@zippity-outdoor.com
704-892-5222 / 877-234-6196
Customer service agents are available to take calls weekdays from 9am-5pm EST.
If you call outside of business hours, please leave a voicemail. To help you
quickly and accurately, please have reference item number ZP19011 and the
specific part name which can be found on page 4. It is helpful if you can
provide the batch lot which is a stamped number inside the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this
product, we are happy to assist you with the process, so please give us a
call at 704-892-5222 / 877-234-6196.
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help
resolve your issues first. If you still decide to return the product, you will
need to initiate the return from the company you originally purchased from.
Detailed Product Dimensions & Specifications
STEP 1: LAY OUT MATERIALS
Surface Mount (2)
NOT INCLUDED WITH PURCHASE:
|
---|---
¼” x 4” Hex Head Bolt w/ Nut and Washer (8)
Only needed if installed on wood| ¼” x 3” Concrete Wedge Anchor (8)
Only needed if installed on concrete
|
¼” Hex Bolts(8)| ¼” Washer (8)
|
2” x 6” Wood Support (1)
Only needed if installed on wood| 1/2” to 1” Hex Head Steel Tek Screws (2)
**STEP 2A: MOUNT TO CONCRETE
**
STEP 2A.1 ►
► Locate the position of your Surface Mount (A) and mark the four
anchor holes. STEP 2A.2 ►
► Drill (4) ¼” diameter holes 3” deep through the concrete. You will need
a hammer drill and a masonry drill bit. Install (4) ¼” x 3” concrete wedge
anchors. STEP 2A.3 ►
► Place the surface mount over the four anchor bolts and check that they
are level.
If there is a slope in the concrete surface, level the base plate with
washer(s) as illustrated. STEP 2A.4 ►
► Once level, place a washer and nut onto each exposed bolt. Fasten them
one by one using a wrench.
STEP 2B: MOUNT TO WOODEN DECK
STEP 2B.1 ►
► Locate the position of your surface mount and mark the four bolt
holes. STEP 2B.2 ►
► Measure the distance between your joists and fasten a 2” x 6” wood
support directly below where the surface mount will be installed. This will
give the surface mount additional structural strength. STEP 2B.3 ►
► Drill (4) ¼” diameter holes through the deck and support. ► Place
the surface mount over the holes and check if it is level. If there is a slope
in the deck surface, level the surface mount base plate as
illustrated. STEP 2B.5 ►
► Once level, fasten the surface mount using (4) ¼” x 4” hex head bolts
with nuts and washers.
STEP 3: INSTALL POST AND CAP
STEP 2B.1 ►
► Place post and post cap over surface mount.
Note: Posts and post caps must be purchased seperately. STEP 2B.3 ►
- Pre-drill (2) holes in the posts at the locations shown below.
- Drive (2) 1/2″ to 1” hex head steel tek screws (not included) into the pre-drilled holes to secure the post.
6935 Reames Rd. Ste. K.
Charlotte, NC 28216
support@zippity-outdoor.com
704-892-5222
877-234-6196
WWW.ZIPPITY-OUTDOOR.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>