Littfinski DatenTechnik Light DEC Service Module for Light DEC Instruction Manual
- October 30, 2023
- Littfinski DatenTechnik
Table of Contents
Littfinski DatenTechnik Light DEC Service Module for Light DEC
Product Information
The Light-DEC-Service Module for Light-DEC is a product from the Digital- Professional-Series by Littfinski DatenTechnik (LDT). It is designed to be used as a kit for assembly.
Product Usage Instructions
- Open the Light-DEC kit and ensure that all the parts are present as listed in the assembly instruction manual.
- Follow the assembly instructions provided in the manual to assemble the Light-DEC-Service Module.
- After assembly, connect the Light-DEC-Service Module to the Light-DEC according to the instructions provided in the Light-DEC user manual.
- Once connected, turn on the power supply and test the Light-DEC-Service Module to ensure it is functioning correctly.
- If any issues are encountered during assembly or usage, refer to the troubleshooting section of the assembly instruction manual or contact Littfinski DatenTechnik (LDT) for further assistance.
Introduction
You have purchased the Light-DEC-Service-Module for your model railway that is supplied within the assortment of Littfinski DatenTechnik (LDT).
- These kits are easy to assemble and they are a product of high quality.
- Model railway kits are not only welcome handicraft jobs but they can be purchased with a considerable price reduction.
This will justify to spend about an hour because you do not need more time to assemble those kits.
We are wishing you having a good time using this product.
General
Tools required for the assembly
Please assure that the following tools are available:
- a small side cutter
- a mini soldering iron with a small tip
- solder tin (if possible 0.5mm diameter)
Safety Instructions (attend as well to the rear side of this instruction)
- We designed our devices for indoor use only.
- All electrical and electronic components included in this kit shall be used on low voltage only by using a tested and approved voltage transducer (transformer). All components are sensitive to heat. During soldering the heat shall be applied for a very short period only.
- The soldering iron develops up to 450°C. Please keep continual attention to this tool. Keep sufficient distance to combustible material. Use a heat resistant pad for this work.
- This kit consist of small parts, which can be possibly swallowed from children. Children (especially under 3 years) should not participate on the assembly without supervision.
Set-Up
For the board-assembly please follow exact the sequence of the below assembly
list. Cross each line off as done after completing the insertion and the
soldering of the respective part.
For the diodes please keep special attention to the correct polarity (marked
line for the cathode).
Before assemble the Display is it required to assemble and solder correctly
the two 10-poles and the 14-poles pin-bars onto the Light-DEC-Service pc-
board. Correct assembly of the two pin-bars will be if the shorter side with
the shorter pins will be inserted into the pc-board.
It is essential that the two 10-poles pin-bar will be inserted that the
soldering will be performed from the printed assembly side of the board.
Then plug-on the display onto the 14-poles pin plug bar and secure it with
distance spacers, Phillips-screws and hexagon nuts as shown below. Now shall
the 14-poles pin plug bar to be soldered to the display.
Assembly List
| Pos. | Qty. | Component | Remarks | Ref. | Done |
|---|---|---|---|---|---|
| 1 | 1 | Pc-board | |||
| 2 | 5 | Diode 1N4148 | attent to the polarity! | D1…D5 | |
| 3 | 4 | Push button | S1…S4 | ||
| 4 | 1 | Trim-pot 10kOhm | P1 | ||
| 5 | 1 | Pin plug bar 2x10poles | attend to direction! | ST1 | |
| 6 | 1 | Pin plug bar 14poles | ST2 | ||
| 7 | 4 | Distance spacer 5mm | for assembly of display | ||
| 8 | 4 | Phillips screw M 2,5 | for assembly of display | ||
| 9 | 4 | Hexagon nut M 2,5 | for assembly of display | ||
| 10 | 1 | Display (Point-Matrix) | display | ||
| 11 | final control |
Assembly Plan
Soldering instruction
Provided you have no special experience in soldering electronic components please read first this soldering instruction before starting the job. Soldering has to be trained!
-
Never use additional fluxes for soldering electronic circuits which contain acids (e.g. zinc chloride or ammonium chloride). Those can destroy components and printed circuits when not washed off completely.
-
As soldering material only lead free soldering tin with a rosin core for fluxing should be used.
-
Use a small soldering iron with max 30 Watt heating power. The solder tip shall be free from scale to assure an excellent heat transfer to the area to be soldered.
-
The soldering shall be performed on a speedy way because a long heat transfer can destroy the components. To much or to long heating can take off the copper pads and copper tracks from the board.
-
For a good soldering a well tinned solder-tip has to be brought in contact to the copper-pad and the component wire at the same time.
Simultaneous a little solder-tin shall be applied for heating up. As soon as the solder-tin starts melting the tin wire has to be taken away.
Just wait until the tin has well wetted the pad and the wire and take the soldering iron away from the soldering area. -
Make sure not to move the just soldered component for about 5 seconds after removing the soldering iron. This should create a silver shining faultless soldering joint.
-
For a faultless soldering joint and well done soldering is a clean nonoxidized soldering-tip absolutely required. It is not possible to perform a sufficient soldering joint with a dirty soldering tip.
Therefore please clean the soldering tip from excessive solder-tin and dirt by using a wet sponge or a silicone cleaning pad after each soldering process. -
After completion of the soldering all connection wires have to be cutted off directly above the soldering joint by using a side cutter.
-
By soldering semiconductors (transistors, diodes), LED
s and ICs is it very important never to exceed the soldering time of 5 seconds to prevent the destruction of the component. It is absolutely required to attend to the correct polarity of the component before starting the soldering process. -
After the board assembly carefully control the pc-board about correct insertion of the components and the correct polarity. Please check if no connections or copper tracks are accidentally short circuited by soldering tin. This can not only result to malfunction of the module but also result to a destruction of expensive components.
-
Please take into account that improper soldering joints, wrong connections, faulty operation or wrong board assembly is not a matter within our sphere of influence.
General installation information
The contact-wires of resistors and diodes to be assembled in a lying position
shall be bended in accordance to the raster distance into a right angular
position and assembled into the specified bores (in accordance to the board
assembly plan or the assembly markings). To prevent that the components will
not fall out by turn-over the pc-board please bend the connection wires about
45° apart and solder them carefully to the copper pads on the rear side of the
board. Finally the excessive wires shall be cutted off with a small side
cutter.
The resistors in the supplied kits are metal-foil resistors. Those have a
tolerance of 1% and are marked with a brown “tolerance-ring”. The tolerance
ring can be identified by the larger margin distance respectively the larger
distance to the other four marking rings. Normally there are five color rings
on the metal-foil resistors. To read the color code you have to locate the
resistor that way that the brown tolerance ring will be on the right side. The
color rings will be red now from left to right!
Please take care to assemble diodes with the correct polarity (position of the
cathode marking). Take care about a very short soldering time! The same will
apply to the transistors and the integrated circuits (IC`s). The flat side of
the transistors has to correspond with the marking on the PC board.
The transistor legs should never be assembled in a crossed position.
Further those components should have a distance of about 5mm to the board.
Attend to the short soldering time to prevent the damage of the component by
excessive heat.
Capacitors shall be assembled into the respective marked bores, the wires to
be bent a little apart and careful soldered to the copper pad. By the assembly
of electrolytic capacitors (electrolytic cap) it has to be attended to the
correct polarity (+,-)! Wrong-way soldered electrolytic capacitors can explode
during the application! Therefore is it very important to check the correct
polarity two- or even better three-times. In addition it has to be attended to
the correct capacitor values, e.g. n10 =100pF (not 10nF!).
A careful and clean assembly will drastically reduce the possibility that
anything will not be in correct function. Check every step and every soldering
joint two times before carrying on! Attend closely to the assembly list!
Perform the described step not different and do not skip any step! Mark each
step as done at the foreseen column after assembly and careful check.
Take your time. Private work is no piece-work because the time for careful
assembly work is much less than an extensive fault diagnosis.
Final assembly
Sockets and integrated circuits (IC´s) of the kits will be supplied on a piece
of foam to assure safe transport.
This foam shall never be used below or between components as this foam is
electrical conductive.
In case the kit will be taken into operation the conductive foam can produce a
short circuitry and destroy the complete kit. Anyhow the function of the
module will not be as expected.
Warranty
As we have no influence to the proper and correct assembly we have to limit our warranty to the complete supply and the faultless quality of the components.
We guarantee the function of the components in accordance to the identified values within a non-assembled condition of the parts and the compliance of the technical data of the circuit by attending to the respective soldering instruction and the specified start of operation of the module including connection and operation.
Further demands are not accepted.
We are not taking over any warranty nor any liability for any harm or
sequential damage connected to this product.
We reserve our right for a repair, rework, supply of replacement or refund of
the purchase price.
The following criteria will result to a non-repair respectively to a lost of right to claim under guarantee:
- if acid-containing soldering tin or fluxes with corrosive content and others have been used
- if the kit has been improper soldered or assembled
- by alterations or repair-trials on the device
- by own circuit amendments
- by construction of non-intended improper displacement of components, free wiring of components etc.
- application of other non-original kit-components
- by damaging of copper tracks or soldering copper pads on the board
- by wrong assembly and the sub sequential damages
- overloading the module
- by damages caused by intervention of foreign persons
- by damages caused by disregarding the operation manual respectively the connection plan
- by connecting a wrong voltage respectively a wrong current
- by wrong polarity connection of the module
- by wrong operation or damages caused by negligent usage or abuse
- by defects caused by bridged or wrong fuses.
All such cases will result to a return of the kit to your expenses.
Subject to technical changes and errors. Ó 05/2013 by LDT
Made in Europe by
Littfinski DatenTechnik (LDT)
Bühler electronic GmbH
Ulmenstraße 43
15370 Fredersdorf / Germany
Phone: +49 (0) 33439 / 867-0
Internet: www.ldt-infocenter.com
Subject to technical changes and errors. Ó 09/2022 by LDT
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>