Onity Repeater Hotel Electronic Locking System Instruction Manual

Onity Repeater Hotel Electronic Locking System

© 2022 Carrier. All rights reserved. Onity is a part of Carrier. Other brand and product names are or may be the trademarks of, and are used to identify products or services of, their respective owners. This document discloses subject matter in which Carrier has proprietary rights. Neither receipt nor possession thereof confers or transfers any right to reproduce or disclose the document, any part thereof, any information contained therein, or any physical article or device, or to practice any method or process, except by written permission from, or written agreement with, Carrier. The information in this document is subject to change without notice. Carrier assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, oft he use or application of any of the contents of this document.

Description

Onity’s Repeater is meant for range extension which is having Bluetooth® 5.1 radio capabilities. It works as a bridge between Lock to room thermostat if Lock or Thermostat unable to communicate each other. It will act as the bridge between th e paired Thermostat & Lock by receiving the data from Lock & sending ahead to Thermostat over Bluetooth®. Devices (Repeater Lock) within a room will be connected and one of the devices (Edge/Proxy) connects to Thermostat of that room, Thermostat connects to RMS system (here Edge router, DMS server) providing path to communicate with Front Desk Server (Onportal server). Devices connected within a room with Thermostat will be called as network branch. The device enrollment process will join a node to the network and creates routing table using which messages to different nodes can be routed But it doesn’t amplify the signal (RF) in any forms, just extend the range by retransmitting the same data as received without any amplification.

Repeater Installation

Each Repeater package includes the following:

• 1 Repeater unit
• 2 AA batteries
• 4 Screws (M3.9 x 25mm)

Overview

1. Batteries (AA, 1.5V, Alkaline)
2. Assy, Repeater, Serene, White
3. Box (4 x 4 x 2), Repeater, Serene
4. Screws (4-M3.9 x 25mm), Round-headed Philips

Exploded View of Repeater

1. Assy, CKA, Control Board, Repeater
2. Assy, Bracket, Repeater, Serene, White
3. PL Housing, Repeater, Serene, White
4. O-Ring, 72 x 3 mm
5. Screws, M3 x 5mm
6. Elast, Gasket, Repeat

Repeater Assembly and Installation

1. Hold Repeater base and rotate enclosure (top cover) clockwise.
2. Insert batteries in top cover, aligning them with the correct polarity.
3. Using the 4 M3.9 x 25mm screws, attach the base to the wall.
4. Attach Repeater housing to base. To do so, align the dot on the Repeater housing with the snap groove on the base, as illustrated below, then push the housing toward the base.
5. Twist the housing while holding the base firmly until it clicks into position.

Certifications

Canada (ISED)| This device complies with Innovation, Science, and Economic Development (ISED) Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1.       This device may not cause interference.

2.       This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20 cm between the radiator and your body.

---|---
United States (FCC)| This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:

1.      This device may not cause harmful interference.

2.      This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user manual, may cause harmful interference to radio communications.

Changes or modifications not expressly approved by Onity Inc. could void the user’s authority to operate the equipment. To comply with FCC RF exposure compliance requirements, the device must be installed to provide a separation distance of at least 20 cm from all persons.

Radiation Exposure Statement:

This product complies with the U.S. RF exposure limit set forth for an uncontrolled environment and is safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user’s body, or if the device is set to

lower output power if such a function is available. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

European Union (CE)| This Class B digital apparatus conforms to the requirements of the following EU directives:

1.      RED, 2.4GHz, Bluetooth Power class 1 (12dBm max)

Environmental Compliance
This product adheres to environmental regulations established by the current European Union (EU) RoHS and WEEE directives.

Label Requirement
The product label must contain the following information:

• FCC ID: R32-10105533G0
• IC: 5058A-10105533G0

General (Product specification/s)

adapter available for North America and Europe**
Connectivity| Bluetooth®
Battery Life| 2 years of normal life

Environmental

Frequency

Regulatory

IP Rating

• IP55

Installations

• Indoor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>