IKEA VARMFRONT Portable Charger Instructions
- October 30, 2023
- Ikea
Table of Contents
VARMFRONT Portable Charger
Instructions
VARMFRONT Portable Charger
| 
---|---
Functions
- POWER button
- LED indicators
- USB-C (charging and supply power)
- USB-A (only supply power)
Charging power bank
- Connect the USB-C cable to the USB-C port of the power bank first and then connect the USB cable to a USB-charger or USB-outlet that can provide sufficient power to charge the power bank. The LED indicators will display the charging status.
Supply power to devices
- Connect the USB cable to USB-C or USB-A port of the power bank first and then connect the USB-cable to your device that you want to charge.
- The power bank will detect a connected device and start charging automatically.
- The LED indicators will display the remaining charge in the power bank during discharging.
Check power status
- Click once on the POWER button and the LED indicators will light up and indicate the remaining power status.
- If the USB cable is not disconnected while the charging process finishes, push the POWER button first to restart the charging.
Small current supply mode
- Press the POWER button for 8 seconds when your device is being charged.
- The function is mainly used to charge certain wearable electronic devices.
When charging a device that needs a charging current less than 100mA via a
USB-A port, this mode should be activated. You can press the button for 3
seconds to exit this mode, it also automatically closes after 2 hours.
Good to know
- USB cable length and quality influences charging speed and performance.
- Devices may get warm during charging; this is completely normal and they will gradually cool down again after they are fully charged.
- Charging time may vary based on the device’s battery capacity, charge level, the age of the battery and the temperature in the surrounding area.
- Storage temperature: -10°C to 25°C (14 °F to 77 °F ).
- Power bank operating temperature: 0°C to 40°C (32 °F to 104 °F ).
- Unplug the power bank from the power source before cleaning and when it is not in use.
- Power bank should not be left discharged for a longer period.
- Power bank should not be charged while in contact with flammable materials like textiles.
WARNING
- Do not modify, disassemble, open, drop, crush, puncture or shred product.
- Only use in dry locations.
- Risk of fires and burns. Do not open, crush, heat above 140°F (60°C) or incinerate.
- Do not subject the product to wet, moist or excessively dusty environments since this can cause damage to the unit.
- Keep the product away from open flames or sunlight to prevent heat buildup.
- Keep the product away from high voltage devices.
- Children should be supervised to ensure they do not play with the product.
- Do not short-circuit the product or its cells.
- In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes.
Product servicing
Do not attempt to repair this product yourself. If you open or remove parts,
you may expose yourself to dangerous voltage points or other risks.
Care instruction
To clean the unit, wipe with a soft cloth moistened with a little mild
detergent. Use another soft dry cloth to wipe dry.
Technical data
Type: E2037
Capacity: 5200mAh/18.72Wh
Input: 5.0Vdc, max 2.1A (USB-C)
Output: 5.0Vdc, 2.4A, 12W total (USB-C, USB-A)
When both ports are used at the same
time, they share 5.0V/2.4A in total.
For indoor use only
Rechargeable Li-Ion battery cell inside.
Manufacturer: IKEA of Sweden AB
Address:
Box 702 SE-343 81 Älmhult SWEDEN
Power button function (E2037)
Current mode| Sleeping mode| Charging mode| Supply power
mode
---|---|---|---
Single press| Shows via LED the remaining charge and that USB-A is ready to
use.| USB-A is ready to use.| No action
Double press| No action| No action| Stop supplying power
Long press| No action| No action| Switch to the small current supply power
mode or back to normal supply power mode
This device complies with Part 15 of the FCC Rules/Innovation Science and
Economic Development Canada’s licenceexempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation of the device.
WARNING:
Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the quipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
**** The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store.
© Inter IKEA Systems B.V. 2022
AA-2379181-3