HAVIT HV1451T Laiton Garden Spike Light Installation Guide

Laiton Garden Spike Light Installation Instructions

Dimensions

Skullcandy Jib Wireless Earbuds Cha...

Skullcandy Jib Wireless Earbuds Charging Instructions

Product Specifications

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Do not exceed maximum wattage restrictions for globes: 12V MR16 = 20w,
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• All electrical connections must be watertight, If a watertight connection is not done, the Warranty will be voided.
• When installing low voltage fittings, Voltage to fitting must be within +or- 5% of the voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining).
• All o-rings and seals must be in place correctly to maintain warranty.
• These instructions may be updated at any time due to product improvements, Please visit the website for most current installation instructions.

Steps for Installation:

1. Make sure that the electrical circuit is free of voltage (master switch off)

2. Place fitting in the desired location

3. Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V

4. Connect the cable –

5. Strip back cable on both fittings and cable run and twist the positive cable from fitting to positive on the cable run, then connect neutral from fitting to neutral on the cable
   run.

6. Solder all joins using solder with either a heat gun or butane gas torch.

7. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. (failure to do this step will void warranty)

8. Heat the heat shrink or crimp the gel cap making sure all connections are covered.

9. The Colour temperature is preset to 3000k, to change remove the cover from the fitting by twisting anti-clockwise and setting it aside. Remove the globe from the fitting and move the switch to the side of
   the globe to desired color temperature.

10. Reinsert the globe by aligning the pins of the globe with the holes of the lampholder and push down gently.

11. Reattach the cover by turning clockwise and gently push down making sure the seals are still in place and caps are tight to avoid any water penetration.

12. Adjust the fitting to the desired position making sure to stop rotating when the fitting cannot rotate anymore If forced fitting will continue to rotate and cause internal cables to become entangled causing the fitting to short. If this is done, the warranty will be voided.

13. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globes:

1. Remove cover from the fitting by twisting while pulling gently and set aside
2. Remove globe by grabbing the outside of the globe and pulling.
3. Re-insert the appropriate globe by inserting the 2 pins into the lampholder and pushing down gently. (Make sure not to exceed max wattage, see product label for correct info)
4. Reattach cover by turning clockwise and gently push down making sure the seals are still in place and caps are tight to avoid any water penetration.

Must be installed by a licensed electrician

Contact Details:

143 Beauchamp Road
Matraville NSW 2036
Australia| Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
---|---
Warranty Terms & Conditions*| Additional Information
---|---
|
https://havit.com.au/pages/warranty-terms-and-conditions| https://havit.com.au/

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>