BOSCH 150 AdvancedAquatak Pressure Washer Instruction Manual

Advanced Aquatak
150 | 160

Original instructions

Safety Notes

Explanation of symbols

General hazard safety alert.

Safety Notes for pressure washer
Never direct the water jet at people, animals, the unit or electric compo- nents.
Warning: High pressure jets can be dangerous if subject to misuse.

According to the applicable regulations, the appliance must never be used on the drinking water network without a system separator. Use a separator as per IEC 61770 Type BA.

Water flowing though a system separator is considered not drinkable.

The Advanced Aquatak 150 is in- tended for use only in premises having a service current capacity ≥100 A per phase, supplied from a distribution network having a nominal voltage of 230 V. If in doubt please contact your Supply Authority.

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

The warning and information signs attached to the unit provide important information for safe operation. Apart from the information in the operating instructions comply with the general safety regulations and regulations for the prevention of acci- dents.

Connecting to the mains

• The voltage indicated on the rating plate must correspond to the voltage of the power source.

• We recommend that this equipment is only connected into a socket which is protected by a circuit-breaker that would be actuated by a 30 mA residu- al current.

• Remove the plug from socket when- ever the machine is left unattended for any period.

• The electric supply installation should comply with IEC 60364-1.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• If the plug is damaged, pay attention to the following:

• Plugs and sockets situated near the work site or outdoors should be to class IP 55 of BS 5490 to provide ad- equate protection against ingress of water, etc. and cable entries require effective sealing. Rubber shrouds should be provided over cable glands. Drip-proof (class IP X2 of BS 5490) plugs and sockets to BS 4343 are suitable for use indoors where the plug is away from the water spray area where the appliance is in use.

• Never touch the mains plug with wet hands.

• Do not pull plug while operating the device.

• Do not run over, crush or pull the power supply cord or extension cord, otherwise it may be damaged. Protect the cable from heat, oil and sharp edges.

• Do not use the unit, if the power sup- ply cord or important parts, e. g. high-pressure hose, power gun or safety devices are damaged.

• Warning: Inadequate extension cords can be dangerous.

• If an extension cord is used, the plug and socket must be of watertight con- struction. The extension cord must have a cross section in accordance with the operating instructions and be protected against splashed water. The connection must not be in water.

• When replacing plugs on the power supply cable or extension lead the spray water guard and mechanical stability must remain intact

Water connection

• Comply with the regulations of your water supply company.

• All connecting hoses must have properly sealed joints.

• Make sure that the supply hose is at least 12.7 mm (1/2″) in diameter and is reinforced.

• The appliance should never be used on the drinking water supply without a back flow valve. Water which has passed the back flow valve is regarded as undrinkable.

• The high-pressure hose must not be damaged (danger of bursting). A damaged high-pressure hose must be replaced immediately. Only use hoses and connections recommended by the manufacturer.

• High-pressure hoses, fittings and couplings are important for the safety of the appliance. Use only hoses, fit- tings and couplings recommended by the manufacturer.

• Only clean or filtered water should be used for intake.

Application

• Before use, check that the unit and operating equipment are in perfect condition and are safe to operate. Do not use the unit if it is not in perfect condition.

• Do not direct the jet against yourself or others in order to clean clothes or footwear.

• Do not use solvent-containing liquids, undiluted acids, acetone or sol- vents! This includes petrol, paint thinners, heating oil. The sprayed vapour is highly flammable, explosive and toxic.

• The appropriate safety regulations must be observed when using the unit in dangerous areas (e. g. petrol stations). It is forbidden to operate the unit in potentially explosive locations.

• The unit must be placed on a solid base.

• Take care if using the machine in a confined space ensuring that there is adequate ventilation. Ensure that all vehicles are switched off at all times whilst cleaning.

• Operation of this machine requires both hands to be used at all times. Do not operate from a ladder. Take care when using the machine on balconies or other raised areas ensuring that you can see any edges at all times.

• Only use detergents recommended by the manufacturer. Comply with the application, disposal and warning instructions of the detergent manufacturers.

• All current-conducting components in the working area must be protected against splashed water.

• The gun trigger must not be jammed in position “ON” during operation.

• Wear suitable protective clothing to protect against splashing from some parts. Do not use the appliance within the range of persons unless they also wear protective clothing.

• If necessary wear personal protective equipment (PPE) e. g. safety goggles, breathing protection etc to protect against water, particles and/or aero- sols sprayed back from parts.

• High pressure may cause objects to rebound. If necessary wear suitable personnel protective equipment such as safety goggles.

• Vehicle tyres/tyre valves may only be cleaned from a minimum distance of 0 cm, otherwise the vehicle tyre/ tyre valve could be damaged by the high-pressure jet. The first indication of this is a discoloration of the tyre. Damaged vehicle tyres/tyre valves

can be extremely dangerous.

• Materials containing asbestos and other materials which contain sub- stances which are hazardous to your health must not be sprayed.

• Detergents must not be used undiluted. The products are safe to use as they contain no acids, alkalis or sub- stances which are detrimental to the environment. We recommend that the detergents are kept out of the reach of children. If detergent comes

into contact with the eyes, wash im- mediately with plenty of water and if swallowed contact a doctor immediately.

• Never use the pressure washer without the filter or with a dirty or damaged filter. Using the pressure washer without a filter or with a dirty or damaged filter may invalidate the warranty.

• Metal parts may become hot after prolonged usage, if necessary wear protective gloves.

• Avoid high pressure washing in bad weather conditions especially when there is a risk of lightning.

Operation

• The operator must use the unit in accordance with the regulations. He/she must take local conditions in- to account and be aware of other peo- ple, especially children, when operat- ing the unit.
• The unit may only be used by author- ised persons who have received training or have demonstrated their ability to operate the unit. The unit must not be operated by children or juveniles (danger of accidents due to incorrect use of the unit).
• Never allow children, persons with physical, sensory or mental limita- tions or a lack of experience and/or knowledge and/or people unfamiliar with these instructions to use the gar- den tool. Local regulations may re- strict the age of the operator.
• Children should be supervised to en- sure that they do not play with the machine.
• The unit must never be left unsuper- vised while the unit is switched on.
• The water jet from the high-pressure nozzle produces a recoil on the gun. You should therefore hold the gun and spray lance firmly with both hands.
• Never use a roto nozzle or pencil jet to clean motor vehicles.

Transport

• Switch off the motor and secure the unit before transporting.

Maintenance

• Switch off the unit prior to all cleaning and maintenance work and before re- placing components. Pull out the mains plug if the unit is mains-operated.
• Repairs may only be carried out by authorised Bosch Service Centres

Accessories and spare parts

• Accessories and spare parts which have been approved by Bosch must be used. Original accessories and spare parts guarantee that the unit can be operated safety and without any breakdowns.

Symbols

The following symbols are important for reading and understanding the operating instructions. Please take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the machine in a better and safer manner

Intended Use

The product is intended for cleaning areas and objects outside the house, tools, vehicles and boats, if the appropriate accessories and cleaning agents approved by Bosch are used.

Intended use is related to operation within 0°C and 40°C ambient temperature.

This product should not be used for professional use.

Technical Data

Pressure washer
Article number| | AdvancedAquatak 150
3 600 HA7 7..| AdvancedAquatak 160
3 600 HA7 8..
---|---|---|---
Rated power| kW| 2.2| 2.6
Supply temperature max.| °C| 40| 40
Supply rate min.| 1/m in| 8| 9.5
Allowable pressure| MPa| 15| 16
Rated pressure| MPa| 11| 12
Rated Flow| 1/min| 7.5| 8.5
Maximum inlet pressure| MPa| 1| 1
Autostop function| | |
Weight according to EPTA-Procedure 01:2014| kg| 21.| 23.
Protection class| | |
Serial number| See serial number (rating plate) on oressure washer.

The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.

Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable mains system conditions.

Malfunctions are not to be expected for system impedances below 0.276 ohm. If in doubt please contact your Supply Authority

Noise/Vibration Information

Sound emission values determined according to EN 60335-2-79.| 3 600 …| HA7 7..| HA7 8..
---|---|---|---

Typically the A-weighted noise levels of the product are:

Sound pressure level

Sound power level

Uncertainty K

|

dB(A)

dB(A)

dB

|

77

88

2

|

79

90

2

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 60335-2-79:

Vibration emission value ah Uncertainty K

|

m/s2

m/s2

|

3.2

1.0

|

2.9

1.0

---|---|---|---

Mounting and Operation

Action
Delivery Scope| Figure
1| Page
264
---|---|---
Adjusting the Handle| 2| 265
Connecting high pressure water supply hose/nozzle| 3| 265
Connecting to the water supply| 4| 266
Switching On and Off| 5-6| 266
Clean the water filter| 7| 267
Clean nozzle| 8| 267
Connecting high pressure gun to lance| 9| 267
Tube Assembly| 10| 268
Connect detergent bottle| 11| 268
Variable Fan lance
Connecting high pressure gun to lance Adjust water jet| 12| 269
Roto lance
Connecting high pressure gun to lance Adjust water jet| 13| 270
Gun storage| 14| 271
Storage| 15| 271
Transport| 16| 272
Selecting Accessories| 17| 273

Starting

For Your Safety
Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.

The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Only use approved exten- sion cables. Contact your Bosch Service Centre for details. If you want to use an extension cable when operating your high pressure washer, only the following cable dimensions should be used:

– 2.5 mm2

– max length 25 m

Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply net- work in accordance with prescribed safety regulations.

If in doubt contact a qualified electrician or the nearest Bosch Service Centre

WARNING! Inadequate extension cables can be dangerous. Extension cable, plug and sock- et must be of watertight construction and in- tended for outdoor use.

Cable connections should be kept dry and off the ground.

For increased electrical safety use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Always check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a Bosch Service Centre.

For products not sold in GB:

WARNING: For your safety, it is required that the plug attached to the machine is connected with the extension cord. The coupling of the extension cord must be protected against splash water, be made of rubber or coated with rubber. The extension cord must be used with a cable strain relief.

To prevent damage to the appliance, do not allow it to operate dry.

Products sold in GB only : Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an author- ised customer service agent. The replacement plug should have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

Operation

Starting

Attach water supply hose (not supplied) to the mains water supply and machine. Connect the product to the mains supply ensuring that the mains switch is in the off position.
Open water tap.

Press the safety lock (back button on the gun handle) to re- lease the trigger. Fully press the trigger until there is a con- stant flow of water to clear the air from the machine and water supply hose. Release trigger. Press the safety lock (front but- ton on the gun handle).

Turn button on main switch. Point the power gun downwards.

Press the trigger safety lock to release the trigger. Fully press the trigger

Autostop function

The machine is designed to switch off the motor when the trigger is released on the gun.

Working Advice

General
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the pressure washer by pulling the hose, this could cause the ma- chine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high pressure hose. Do not expose the high pressure hose to sharp edges or corners.

• Never use a roto nozzle or pencil jet to clean motor vehicles.

WARNING! The Patio Cleaners supplied are only intended to be used on flat surfaces! Do not attempt to use them on steps. Never attempt to touch the rotating nozzle while operating the machine!

Working advice for clea ning with detergents

• Only use cleaning agents suitable specifically for high pressure washers.

We recommend that you use detergent sparingly for the sake of the environment. Observe the recommended dilution on the detergent label.

The high-pressure foam nozzle supplied with this product includes a regulator to control detergent use. Adjust as required.

Recommended cleaning method

Step 1: Attach the fixed fan nozzle and remove the heavy dirt.

Step 2: Attach the foam bottle and spray on the detergent sparingly.

Step 3: Rinse off the loosened dirt and detergent with the fan nozzle.

Note: When cleaning a vertical surface spray off dirt/detergent from the bottom and work in an upwards direction. Rinse from the top and work downwards.

Use with alternative water sources
This high-pressure washer will self prime and can draw water from water tanks and natural water sources. It’s IMPORTANT that the water is clean and the BOSCH inlet filter is clear and fitted to the machine.

Open tanks/containers an d natural water sources

Use the Self Priming accessory kit comprising:

– Inlet strainer with non return valve

–3m reinforced supply hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m above the water level in the source in approximately 15 sec- onds.

Submerge the 3 m hose in water to displace the air. Connect the 3 m supply hose to the pressure washer ensuring that the inlet strainer remains submerged in the water source.

Run the pressure washer with the gun disconnected until a steady flow of water appears from the high pressure hose. Stop if this has this has not been achieved within 25 seconds and check all the connections. Switch off and connect the gun, lance and nozzle to operate.

It is important to ensure that all hose and coupling connections are of good quality, air tight and that all washers are in good condition and correctly seated in place. Failure to do so may affect the self priming performance.

Water Tanks with outlet connections
When connecting the pressure washer to a water tank with a suitable tap outlet, first connect the supply hose (not provid- ed) to the tank outlet, open the tap to allow the water to dis- place all the air in the hose and then connect to the pressure washer.

Troubleshooting

the model tag
Motor protector has activated| Allow to cool for 15 minutes
Fuses blow| Fuses incorrectly rated| Change to a mains supply higher than the pressure washer amp consumption
Motor starts but no pressure| Nozzle partly blocked| Clean nozzle
Motor “sounds’ but fails to start| Insufficient power supply| Check that the voltage of the mains power supply line is the same as that on the plate
Voltage loss due to use of extension cable| Check characteristics of extension cable
Appliance not used for a long period of time| Contact your Bosch Service Centre
Problems with TSS (Total Stop System) device| Contact your Bosch Service Centre
Pressure pulsating| Air in the inlet water supply hose/pump| Allow pressure washer to run with open spray handle and nozzle at low pressure until regular working pressure is obtained
Inadequate water supply| Check that the water supply corresponds to specifications. The minimum specification for the water supply hose is 1/2″ or 13 mm diameter
Water filter blocked| Clean water filter
Water supply hoses sq ueezed| Straighten out kinked water supply hoses
High pressure hose too long| Remove high pressure extension hose. Retry (extension hose max. 7 m)
Pressure too low. but steady
Note: Several types of accessory will normally deliver a lower pres sure| Nozzle worn| Change the nozzle
Start/stop valve worn| Activate trigger five times in quick succession
Motor starts up but with restricted or no working pressure| No water supply| Connect water supply
Water filter clogged up| Clean the water filter
Nozzle clogged up| Clean nozzle

The pressure washer starts irregularly by itself

| Pump/power gun leaky| Contact your Bosch Service Centre
Water leaks from machine| Leaking pump|

A slight water leak is permissible; in case of excessive leak, contact Bosch Service Centre

Maintenance and Service

Maintenance

• Stop, remove plug from the power supply and disconnect from water supply.

Note: To ensure long and reliable service, carry out the following maintenance regularly.
Regularly check for obvious defects such as loose fixings, and worn or damaged components. Check that covers and guards are undamaged and correctly fitted. Carry out necessary maintenance or repairs before us- ing.

If the replacement of the supply cord is necessary, this has to be done by Bosch or an authorized Bosch service agent in or- der to avoid a safety hazard.

After use/Storage

Turn the main switch off and operate the trigger to drain the water from the high pressure hose.

Clean the exterior of the machine thoroughly using a soft brush or cloth. Do not use water, solvents or polishes. Remove all debris, especially from the ventilation slots.

End of season storage: Drain water out of pump running motor for a few seconds. Pull trigger to release all water.

Do not place other objects on top of the machine.

Store in a frost-free area.

Ensure cables are not trapped when storing. Do not kink high pressure hose.

After-sales Service an d Application Service

www.bosch-do-it.com

In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the machine

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.

Tel. Service: (0344) 7360109

E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: (01) 4666700

Fax: (01) 4666888

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: (01300) 307044

Fax: (01300) 307045

Inside New Zealand:

Phone: (0800) 543353

Fax: (0800) 428570

Outside AU and NZ:

Phone: +61 3 95415555

www.bosch.com.au

Republic of South Africa

Customer service

Hotline: (011) 6519600

Gauteng – BSC Service Centre

35 Roper Street, New Centre Johannesburg

Tel.: (011) 4939375

Fax: (011) 4930126

E-Mail: bsctools@icon.co.za

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: (031) 7012120

Fax: (031) 7012446

E-Mail: bsc.dur@za.bosch.com

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: (021) 5512577

Fax: (021) 5513223

E-Mail: bsc@zsd.co.za

Bosch Headquarters

Midrand, Gauteng

Tel.: (011) 6519600

Fax: (011) 6519880

E-Mail: rbsa-hq.pts@za.bosch.com

Environmental Protection

Chemicals dangerous to the environment must not be allowed to enter the ground, ground water or ponds, streams, etc.
For the use of cleaning agents, observe the instructions on the package and the prescribed concentration exactly.

For the cleaning of motor vehicles the local regulations should be observed: Do not allow oil sprayed off to enter into the ground water. Recycle raw materials instead of waste disposal

Disposal

The pressure washer, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of pressure washers into household waste!

Only for EC countries:

**** According to the European directive 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation in- to national law, electrical and electronic equipment that are no longer usable must be collected separately and disposed of in an environmentally correct manner.

Subject to change without notice.

EU Declaration of Conformity
Pressure washer Article number

We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards

Advanced Aquatak

150

Advanced Aquatak

160

|

3 600 HA7 7..

3 600 HA7 8..

|

2011/65/EU

2014/30/EU

2006/42/EC

2000/14/EC

EN 60335-1:2012+A11:2014

EN 60335-2-79:2012

EN 55014-1:2006 + A1:2009 + A2:2011

EN 55014-2:1997 + A1:2001 + A2:2008

EN 61000-3-2:2014

EN 61000-3-11:2000

EN 50581:2012

---|---|---

Advanced Aquatak 150

2000/14/EC: Measured sound power level 88 dB(A), uncertainty K =2 dB, guaranteed sound power level 90 dB(A); Conformity assessment procedure in accordance with annex V. Product category: 27
Advanced Aquatak 160

2000/14/EC: Measured sound power level 90 dB(A), uncertainty K =2 dB, guaranteed sound power level 92 dB(A); Conformity assessment procedure in accordance with annex V. Product category: 27

Technical file at: *

• Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2, Stowmarket, Suffolk IP14 1EY, England

Robert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANY Stuttgart, 01.01.2017

Robert Bosch Power Tools GmbH

70538 Stuttgart

GERMANY

www.bosch-do-it.com

F 016 L81 291 (2017.07) O / 281

References

• Location selection | Bosch DIY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>