OBARTER X7-1-VN1229 High Powered Scooter Instruction Manual

OBARTER X7-1-VN1229 High Powered Scooter Instruction Manual

The main components

The main technical parameters

Parameters

Performance and specifications| Maximum speed| About 80-100km/h(depend on scooter Motor or Voltage )
Maximum mileage| 80-250km(depend on Battery Capacity)
Maximum Load| About 180kg
Scooter weight A| bout 65-75kg(depend on model & battery)
size| 153x66x135cm (Open Size)156x66x70cm (Folded Size)
Start form| Factory default zero start
assemblyunit| Motor (brushless motor)| 4000W x 2pcs
Battery Voltage| 60v/60AH
Instrument| Multifunctional LCD instrument
Headlight| LED Headlights (with Horn)
Breaker| Front and rear Brake by Fluid
Break Handgrip| Power brake
Front and rear wheels| Inflatable ( 14inch )
Plastic parts| Environmentally friendly high-strength plastic parts

• Disclaimer:
• Please abide by the relevant laws and regulations of the local bike ride ，
• The Company are not responsible to all the consequences of speeding up
• for personal reasons.

Scooter Detail

1. Big srceen
2. Display
3. Accelerator
4. Handle Bar
5. Signal button
6. ECO /turbo
7. ECO /turbo
8. Horn button
9. Turn Signal button
10. Front Light button
11. Brake Bar

Display Manual

Total mileage ODO, single TRIP, digital voltage display VOL, fault code ERR.

  Parameter setting

001
P02| Mileage unit, 0: KM; 1: the MILE;| 000
P03| Battery voltage grade: the default 60V;| 060
P04| Sleep time: 0, no sleep; Other Numbers are sleep time, range: 1-60; Per minute;| 010
P05| Power assist system gear: 0-3;| 003
P06| Wheel diameter: unit, inch; Accuracy: 0.1; If speed is not accurate, change this value.| 13.1
P07| Speed measurement magnetic steel number: range: 0-255;| 030
P08| Speed limit: range 0-100km/h, not open| 100
P09| Zero start, non-zero start setting, 0: zero start: 1: non-zero start.Power output is available when the vehicle speed reaches 5km/h:| 000
P10| Drive mode setting0: power drive (determine how much power is output through the power gear, at this point the handlebar is invalid.1:Electric drive (by turning the drive handle, the power gear is invalid).2:Both power- assisted drive and electric drive coexist at the same time (under zero starting state of electric drive is invalid).| 002
P11| Power assist sensitivity setting.| 002
P12| Start power| 005
P13| Type setting of booster magnetic steel disc.| 005
P14| The controller’s current limiting value is set as the default 12A range: 1-20a| 012
P15| Motor speed limite setting for P08| 100
P16| 0; Not to be able to cruise, 1; Enable cruising; Automaticcruise after 8s(valid for Second protocol only)| 000
P99| Useless| 099

Buttons and interface.

1. Long press “Power” button when the meter is off: After power on, short press “Power” button, interface switch between ODO, TRIP, VOL
2. Long press “Power” button to power off. Press “Mode” button to switch GEAR
3. long press “Power” button +“Mode”button to enter the boot password and menu Settings selection interface (SO interface),in SO Interface, short press “Power” button Key toggle password number, short press“Mode”button Key changes current item value;

The operating instructions for folding

First
take out the Unlock button first;

Then Press the fold button to fold it.

Pedal Lock Password Reset

• looksnith
  

• Reset Password
  

• packed
  

Pedal Lock Reset Passward Steps. (Original Passward is 000)

1. Use tool sets to take out the handle of the pedal.
2. Turn on the Pedal Lock (with original passward).
3. Use tool to insert the small hole of the lock. Then reset the new Pass ward that you want (such as 123).
4. Take out the tool, then reset passward “123” finished.
5. Reinstall the pedal handle .

Notes ： Pls do not forget the new passward if you have reseted the passpard.

The procedure for removing the battery

Announcements

Safe driving

In the acceleration or deceleration time, be aware to avoid the body’s gravity in the hand, to avoid the body forward. The standing posture should be keeping your feet one after the other, thus lead to more secure and stable riding.

A. When turning, the body is parallel to the handle. Please pay attention to the road condition before turning. Be sure it is safe and then turn.

B. When the brakes, the gravity center of body backwards. It is better to learn to control the center of gravity when braking. Otherwise it will cause two situations: the car tilted forward, as well as brake and steering system damage.

Charging Steps

(Very importand, pls as below steps to charging）

1. Connect the charger to the scooter first.
2. Insert Plug the Electric City (110V -240V or OK).
3. the charger with green light is full charged, Red light is on charging.
4. he warranty reference for Electric Scooter
5. When charging, please put safe place where children can not touch.
6. The red light indicates charging and the green light indicates charging is complete.
7. If you do not use it for a long time, charge it every 2 months.
8. Do not charge in a damp place.
9. Do not run the motor while charging.
10. Avoid contact with the material leak out of the battery accidentally.
11. Failure to store or recharge in accordance with the correct method may result in damage to the battery and no charge.

The warranty reference for Electric Scooter

Note:
Damage caused by human factors is not covered by the warranty. In the free
warranty period, we do not charge maintenance fees. (Note: not include material costs) But the resulting transport costs borne by both parties. The company has the final interpretation.

User warranty card

User name

| Purchasing date
---|---
Tel| Address
Product name| Model
Purchasing store| Breakdown description

Note:
Due to the company’s product upgrades, may part of the display of the product content you get will be different from the instructions, but will not affect your normal use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>