TAFFIO KM3D-360 360 Degree Camera System Parking System Installation Guide

TAFFIO® 360° Camera-System Parking System
Article No.: KM3D-360
Easy Installation

Delivery Content

Connection

Product Introduction

The three-dimensional 360-degree panoramic visual parking assist system uses 4 ultra-wide-angle cameras installed on the front, rear, left, and The images around the vehicle are collected at time, and after correction and stitching by the image processing unit, a 360-degree three-dimensional panorama around the vehicle is formed, which is transmitted to the display device of the center console in real time.
Through the 360-degree panoramic visualization system, the driver can intuitively see the location of the vehicle and the obstacles around the vehicle from the vehicle, and calmly control the vehicle to park and pass through complex roads, effectively reducing scratches, collisions, and obstacles. The occurrence of accidents such as sinking.

Specifications

Features:

1. Multiple video output methods: CVBS, VGA, AHD, TVI;
2. Multiple viewing angles: including more than a dozen viewing angles, covering all customer use scenarios;
3. Knob control: One key to open/close 360, various view angles can be switched instantly;
4. True 3D: 3D viewing angle can be switched in any direction;
5. Various dynamic effects: door switch, wheel speed/direction, forward/backward, 3D stereo radar real-time display;
6. Built-in dozens of 3D car models: built-in 3D car models of dozens of hot-selling models, which are still increasing;
7. The license plate number can be customized and entered at will. 7 colors of each car model can be switched arbitrarily;
8. Support dual CAN gussets, insert dual CAN boards into dual CAN 3D all-in-one in seconds;
9. You can choose the style of each trajectory line, the radar starts, and the trajectory follows;
10. Parking monitoring, one shot per second, up to 24 hours parking monitoring;
11. Compatible with Haisi’s calibration cloth, two large cloth manuals, two large and two small manuals, two large and two small automatics;
12. The size of the 3D viewing angle, the height of the viewing angle, the 3D elevation, and the length of the 3D car model can be adjusted, so that there is no ghost on the top of the 3D. When displayed on any screen, the 3D car model is of normal proportions and will not be stretched;

Detailed product function

Display interface

The display modes include: 2D display, 3D display, narrow-lane limited width mode, front-to-rear wide-angle, front and rear view zoom, and so on.

1. 2D pre-streaming
2. 2D front display
3. 2D front zoom (front of the car)
4. 2D post-streaming
5. 2D front view
6. 2D rear zoom (car rear)
7. Horizontal 2D
8. The front and left are displayed at the same time
9. The body is displayed at the same time
10. 3D left view
11. 3D rear view
12. 3D right view
13. 3D rotating view

2. Menu interface

Main menu functions: driving record, video setting, control setting, panoramic debugging, display setting, system setting, version information
1. Driving record

1.1 Press the direction keys of the remote control (or the previous page and the next page of the menu) to find the time period video file to be played. The selected video file will have a “√” after pressing the OK button.
1.2 After selecting the video file, click the “Play” menu to enter the playback interface. The default is 4 cameras at the same time playback. You can select the up, down, left, and right direction keys in the function menu below to play back the front, back, left, and right separate cameras. You can also choose to pause and fast forward. , Fast rewind function icon operation.
1.3 Lock and protect important video files. After the selected video file is marked with “√”, click the “lock” menu below. The locked video file has a “lock” icon in front of it, so that the locked video file will not be It is overwritten by the system’s automatic loop recording. The locked recording file can be unlocked through the “Unlock” menu below, and the lock icon disappears.
1.4 You can manually delete the video files in the list (including the video files protected by the lock). Select the file to be deleted and click the “Delete” menu below to delete it.
1.5 When the host is powered on, the system will automatically record in a loop, and the duration of each recording is 5 minutes.
2. Video settings

2.1 Video switch: off/on (default on), no video after closing, no red dot is displayed in the upper left corner.
2.2 Storage location: USB
2.3 Format: After the U disk is formatted, all contents in the U disk will be cleared.
2.4 Time setting: Set the system time of the panoramic host.
3. Control settings

3.1 Start mode
Automatic start: 360 will start automatically after each ignition;
Smart start: 360 will not start automatically after each ignition, the user will reverse gear, turn, and then start 360 when the P key is pressed;
3.2 Emergency light control
Simultaneous display of left and right: When the emergency light is turned on, the images of the left and right cameras will be displayed at the same time;
Streaming media: when the emergency light is turned on, the front and back streaming media screens will be displayed; off: when the emergency light is turned on, the 360 display will not be switched;
3.3 Turn signal control
Turn on: the turn signal can turn on 360 panorama;
Off: the turn signal can’t turn on 360 panorama;
3.4 Turn signal display
Corrected view: When the left and right turn signals are turned on, the left and right corrected view is displayed;
3D view: when the left and right turn signals are turned on, the left and right 3D views are displayed; Original view: when the left and right turn lights are turned on, the left and right original views are displayed;
3.5 Radar start
Start: the radar can start 360 panorama;
Off: Radar cannot start 360 panorama;
3.6 Front and back view
Original view: the front and rear views are displayed as original views;
Corrected view: the front and rear views are displayed as corrected views;
3.6 Follow the trajectory
Open: When the front and back are displayed as the corrected view, the view will move with the change of the track line;
Close: Close the track follow function;
3.7 Display delay
10 seconds: When the 360 is turned on, when the user does not perform any operation, the 360 will be automatically turned off after 10 seconds
30 seconds: When the 360 is on, when the user does not perform any operation, the 360 will be automatically closed after 30 seconds
1 minute: When the 360 is turned on, when the user does not perform any operation, the 360 will be automatically turned off after 1 minute
5 minutes: When the 360 is turned on, when the user does not perform any operation, the 360 will be automatically turned off after 5 minutes
3.8 Encoder
Select the matching decoder model
4. Panorama adjustment:

4.1 Vehicle length (CM): The vehicle length is the actual distance between the front and rear tuning cloths.
4.2 Vehicle width (CM): The vehicle width is the actual distance between the outer sides of the tires on both sides of the vehicle body.
4.3 Left-Right Offset (CM): the distance from the front side of the fabric to the shortest point of the left and right fabric.
4.4 Optical lens: Choose the corresponding lens according to the actual installed camera, there are HK8296; HK8255……
4.5 Photosensitive chip: According to the actual installed camera, select the corresponding photosensitive chip, there are SONY225; SC1233…
4.6 Automatic calibration
4.1.1 Tool preparation and precautions before automatic adjustment:

1. Two large and two small calibration cloths: front and rear calibration cloth size 4.4×1.2m; left and right calibration cloth size 1.2×1.6m
2. 2~4 measuring tapes: the measuring range can measure more than 7.5M (inclusive).
3. Site requirements: 12 meters long / 6 meters wide and open and the ground should be relatively balanced (not on slopes or places with uneven ground).
4. Environmental requirements: The daily light brightness is the best, not under the sun or in a dark place, otherwise it will affect the splicing.
5. The front and back calibration cloth should be parallel to the car. Use a ruler to measure the distance between the two large cloths on the left and the front and the two large cloths on the right. The error should be less than 2cm.

4.7 Lens correction

When the calibration effect is not very good, you can enter the lens correction, and perform lens correction on the four cameras, front, rear, left, and right.
Correction method:

1. Choose front, rear, left and right cameras;
2. Click “Lens Calibration”
3. Use the up, down, left, and right buttons on the remote control to move the red circle in the figure above to make the red circle and the black vignetting corner of the camera concentric.
4. After adjusting into concentric circles, press ok on the remote control to complete the lens correction of the camera

4.8 Manual calibration 1
4.8.1 Tool preparation and precautions before manual adjustment:

1. Calibration cloth: the front and back calibration cloth size is 4.4×1.2m; (the same as the automatic splicing cloth, the size of the black grid on the cloth is 60×60 cm, when manual splicing, the left and right calibration cloths are not used)
2. The placement position of the calibration cloth and the order of tracing points

4.9 Manual calibration 2
Tool preparation and precautions before manual adjustment:

1. Calibration cloth: the front and back calibration cloth size is 4.4×1.2m; (it is different from manual calibration and automatic splicing cloth, the size of the black grid on the cloth is 1x1m)
2. The placement position of the calibration cloth and the order of tracing points

Display settings:

5.1 Output format
Users can set output formats such as NTSC/PAL, VGA1280_720, VGA720_480, VGA720_576, AHD, TVI, etc.
5.2 Language setting
Simplified Chinese by default
5.3 Power-on rotation
Turn on: 360 turns on the automatic 3D rotation function. Turn off: 360 turns on without the automatic 3D rotation function.
5.4 Color management
The brightness, saturation, contrast, and sharpness of the displayed image can be adjusted.
The adjustment range is 0~100, and the default value is 50.
5.5 2D position
You can set whether the 2D view is on the left or on the right
5.6 3D view adjustment

After installing 360, when the user wants to adjust the 3D viewing angle, he can adjust it in the following ways:
Angle of view height: After clicking the ok button, select “up” and “down” to adjust the angle of view of the 3D view;
Viewing angle: After clicking the ok button, select “up” and “down” to adjust the field of view of the 3D view;
3D elevation: After clicking the ok button, select “up” and “down” to adjust the height and height of the 3D elevation; car model length: after clicking the ok button, select “up” and “down” to adjust the 3D The length of the car model;

5.7 2D view adjustment

Left front view: press OK, after entering, use the up, down, left, and right icons to adjust the display content of the left front view; Right front view: press the OK key, after entering, use the up, down, left, and right icons to adjust the display content of the right front view; Left rear view: press OK After entering, use the up, down, left, and right icons to adjust the display content of the left rear view; Right rear view: press OK, after entering, use the up, down, left, and right icons to adjust the display content of the right rear view; Front view: press OK to enter After that, use the up, down, left, and right icons to adjust the display content of the front view; Rear view: press OK, after entering, use the up, down, left, and right icons to adjust the display content of the rear view; when the view display content is not completely blocked, you can use the following methods Perform window adjustment:
Left position: press the OK key, after entering, use the up, down, left, and right icons to adjust the display position on the left side of the window; right position: press the OK key, after entering, use the up, down, left, and right icons to adjust the display position on the right side of the window; top position : Press the OK key, after entering, use the up, down, left, and right icons to adjust the display position at the top of the window; Bottom position: press the OK key, after entering, use the up, down, left, and right icons to adjust the display position at the bottom of the window;
5.8 Track line style
The default is Audi, with Audi; Mercedes-Benz; BMW; Lexus; Cadillac; Volkswagen. Track style is optional.
5.9 Car model selection
The default is a neutral sedan, with a neutral sedan; Porsche SUV; BMW sedan; Mercedes-Benz sedan; Audi SUV; Lexus SUV; Volkswagen SUV models are available.
5.10 Car model color
The default is green, with white; black; red; gray; blue; green; brown is optional.
5.11 License plate setting
A complete license plate number can be set.
5.12 Car Series/Model Selection
Not used.

6. System settings

6.1 System upgrade: insert the U disk with the software copied, press the “OK” button, the system will automatically upgrade, and a dialog box will pop up, and the power cannot be cut off during the upgrade process.
6.2 Snapshot mode: Press the number “9” key of the remote control to save the image displayed on the screen to the U disk, and each press can save a picture.
6.3 Export parameters: Insert the U disk and press the “OK” key to save the set and spliced parameters to the U disk.
6.4 Import parameters: Insert the U disk that exported the parameters, and press the “OK” button to import the settings and splicing parameters in the U disk to the 360 host.
6.5 Save default parameters: backup all current set parameters.
6.6 Restore default parameters: restore to the last set parameters that have been backed up.
6.7 Restore factory parameters: restore the factory preset default parameters.

Version information

Software and hardware version information of the current machine

Wireless knob

There are 4 operation modes for the knob:

1. Short press:
   When the 360 panorama is not open, short press the knob to open the 360 panorama; when the 360 panorama is open, short press the knob, which is equivalent to the ok key of the remote control;

2. Left-handed:
   When 360 panorama is turned on, turn the knob to the left to switch related views;

3. Right-handed:
   When 360 panorama is turned on, turn the knob to the left to switch related views to the right;

4. Long press:
   When the 360 panorama is turned on, long press the knob for 1s to return to the previous menu, which is equivalent to the return key of the remote control; when the 360 panorama is in the 2D view mode, long press the knob for 1s to close the 360 panorama;

Note: After the knob is not operated for a period of time, in order to save power, it will automatically enter the dormant state. When the user needs to use the knob again, he needs to short press the ok key or rotate the knob left and right to wake up the knob and enter the normal working mode.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>