DERBEE ASW-28 Electrical Glider PNP Instruction Manual
- October 30, 2023
- DERBEE
Table of Contents
ASW-28 Electrical Glider PNP
Instruction Manual
SAFETY INSTRUCTIONS
WARNING: Read the entire assembly instructions to familiarise yourself with the product functions and safety instructions before operation. As the user of this product, you are solely responsible for operation that does not endanger yourself or others, or damage the product or property of others.
THIS IS NOT A TOY!
Not for children under 14 years.
- Always keep a safe distance in all directions from your model to avoid collisions and injuries. This model is controlled by a radio signal. Radio signals can be interfered with from outside without you being able to influence it. Interference may result in a temporary loss of control.
- Always operate your model in open areas – away from cars, traffic and people.
- Always carefully follow the instructions and warnings for this product and any optional accessories (chargers, rechargeable batteries, etc.).
- Always keep all chemicals, small parts and electrical components out of the reach of children.
- Never operate your model with weak transmitter batteries.
- Always keep the model in sight and under control.
- Only use fully charged batteries.
- Always keep the transmitter switched on when the model is powered up.
- Always remove the battery before taking the model apart.
- Always keep moving parts clean.
- Always keep parts dry.
- Always allow parts to cool before touching them.
- Always remove the battery after use.
- Always make sure the failsafe is properly set before flying.
- Never operate the model with damaged wiring.
- Never touch moving parts.
NOTES ON ENVIRONMENTAL PROTECTION
This
product must not be disposed of with other waste. Instead, it is the user‘s
responsibility to take the waste equipment to a designated recycling
collection point for electrical and electronic equipment. Separate collection
and recycling of your waste equipment at the time of disposal will help to
save raw materials and ensure that its recycling protects human health and the
environment. For more information on where you can drop off your waste
equipment for recycling, please contact your local council, your household
waste disposal service or the point of sale of your product.
SPECIFICATIONS
| 2020 mm
---|---
| 1165 mm
| 1800 g
| BL 3542-850KV
| 40A
| 6x 9g MG
| 2200mAh 4S (required)
REQUIRED
| Battery | LIPO 2200 14,8 V – XT60 |
|---|---|
| Charger | Lipo Charger |
| RC System | 6+ Channels |
SPARE PARTS
| Art.-Nr. | Bezeichnung |
|---|---|
| DBASW17200.1 | DERBEE ASW-28 200cm – Fuselage |
| DBASW17200.2 | DERBEE ASW-28 200cm – Wings L+R |
| DBASW17200.3 | DERBEE ASW-28 200cm – Canoby |
| DBASW17200.4 | DERBEE ASW-28 200cm – Elevator |
| DBASW17200.5 | DERBEE ASW-28 200cm – Winglets L+R |
| DBASW17200.6 | DERBEE ASW-28 200cm – Spinner |
| DBASW17200.7 | DERBEE ASW-28 200cm – Folding Prop 11×6 |
| DBASW17200.8 | DERBEE ASW-28 200cm – Screw Set |
| DBASW17200.9 | DERBEE ASW-28 200cm – Tube |
| DBASW17200.10 | DERBEE ASW-28 200cm – Wheel |
| DBASW17200.11 | DERBEE ASW-28 200cm – Wing Connector |
| DBASW17200.12 | DERBEE ASW-28 200cm – Propeller clutch |
| DBASW17200.13 | DERBEE Brushless Motor 3542(KV850) |
| DBASW17200.14 | DERBEE ASW-28 200cm – Servo MG 9g – Eleveator Cable 80mm |
| DBASW17200.15 | DERBEE ASW-28 200cm – Servo MG 9g – Flap L Cable 210mm |
| DBASW17200.16 | DERBEE ASW-28 200cm – Servo MG 9g – Flap R Cable 300mm |
| DBASW17200.17 | DERBEE ASW-28 200cm – Servo MG 9g – Rudder Cable 150mm |
| DBASW17200.18 | DERBEE ASW-28 200cm – Servo MG 9g – Aileron Cable 650mm |
| DBASW17200.19 | DERBEE 40A ESC/XT60 Brushless ESC |
| DBASW17200.20 | DERBEE ASW-28 200cm – Decal Sheet |
ASSEMBLY OF THE ELEVATOR
- To assemble the tailplane, you will need the fuselage, tailplane, 2x M3*17mm screws and a suitable screwdriver.
- Connect the servo plug of the tailplane to the servo socket in the rudder of the fuselage.
- Place the tailplane on top of the rudder of the fuselage and fasten it with the two M3*17mm screws.
- For the assembly of the wingtips both wing halves and both wingtips are needed.
- Prepare the wingtips tomatch the wing half.
- Attach the wingtips to the ends of the wing halves.
- To assemble the wing halves, you will need the fuselage, wing connectors, wing halves, 4x M4*10mm screws and an appropriate screwdriver.
- The wing tubes are handtightened into the corresponding M4 receptacle in the fuselage on the left and right.
- Fit the two wing halves onto the wing connectors and push them into the corresponding receptacle in the fuselage.
- Turn the model over and attach the two wing halves to the fuselage with the M4*10mm screws.
- Ready assembled model.
Now install the remaining RC components such as the receiver and battery. Now the transmitter can be programmed. The rudder deflections and the centre of gravity can be taken from the following tables. The values given are approximate values.
RUDDER DEFLECTIONS
| Function | Normal |
|---|---|
| Ailerons | +17 mm / -9 mm |
| Flaps | 25-30mm (runter) |
| Elevator | +10mm / -10mm |
| Rudder | +20mm / -20mm |
DERBEE GERMANY
D-Power Modellbau
Horst Derkum
Sürther Str. 92-94
50996 Köln, Germany
info@d-power-modellbau.com
+49 221 346 641 57
www.d-power-modellbau.com| DERBEE
BELGIUM
Beez2B sprl
rue de Thy 54
B-1470 Baisy-Thy
Belgium
info@beez2b.com
+32 23 76 71 82
www.beez2b.com
---|---
(c) 2023 
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>