makita DUR368L Cordless Grass Trimmer Instruction Manual
- October 30, 2023
- Makita
Table of Contents
- makita DUR368L Cordless Grass Trimmer
- Product Information
- Product Usage Instructions
- SPECIFICATIONS
- Symbols
- SAFETY WARNINGS
- PARTS DESCRIPTION
- FUNCTIONAL DESCRIPTION
- ASSEMBLY
- OPERATION
- MAINTENANCE
- TROUBLESHOOTING
- OPTIONAL ACCESSORIES
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
makita DUR368L Cordless Grass Trimmer
Product Information
The Cordless Grass Trimmer is a battery-powered garden tool designed to trim grass and weeds in areas that are difficult to reach with a lawnmower. The trimmer comes in several models with different handle types, including bike handle and loop handle. It has a variable speed control system that allows users to adjust the cutting speed according to the task at hand. The trimmer can be used with different cutting tools, including a 3-tooth blade, a 4-tooth blade, an 8-tooth blade, a nylon cutting head, and a plastic blade. It has a noise level of 74.7 dB(A) to 76.4 dB(A) depending on the model and cutting tool used. The trimmer is compatible with various battery cartridges, battery adapters, and chargers, as listed in the product specifications.
Product Usage Instructions
- Choose the appropriate handle type for your comfort and convenience. The bike handle is ideal for heavy-duty work, while the loop handle is best for light-duty work.
- Select the appropriate cutting tool based on the type of vegetation you need to trim. The 3-tooth blade is recommended for thick and woody vegetation, while the nylon cutting head is best for grass and light weeds.
- Make sure the battery cartridge is fully charged before use. Use only the compatible battery cartridges, battery adapters, and chargers listed in the product specifications.
- Attach the cutting tool securely to the trimmer head according to the manufacturer’s instructions.
- Turn on the trimmer by pressing the power button and adjust the cutting speed as needed using the variable speed control system.
- Hold the trimmer with both hands and position it at a comfortable angle to the vegetation you wish to trim.
- Move the trimmer back and forth in a sweeping motion to cut the vegetation. Use caution when trimming near obstacles or hard surfaces.
- When finished, turn off the trimmer and remove the cutting tool. Clean the trimmer and cutting tool according to the manufacturer’s instructions, and store them in a safe place.
WARNING: Wear ear protection when using the trimmer as the noise level may be harmful to hearing. Do not use any other battery cartridges, battery adapters, and chargers than those listed in the product specifications as it may cause injury and/or fire. The noise emission during actual use of the trimmer can differ from the declared value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
SPECIFICATIONS
Model: | DUR368A | DUR368L |
---|---|---|
Handle type | Bike handle | Loop handle |
No load speed (at each rotation speed level) | Cutter blade / Nylon cutting | |
head / Plastic blade | 3: 6,500 min-1 |
2: 5,300 min-1
1: 3,500 min-1
Overall length (without cutting tool)| 1,758 mm
Nylon cord diameter| 2.0 – 2.4 mm
Applicable cutting tool and cutting diameter| 3-tooth blade (P/N: 195298-3)|
230 mm
4-tooth blade (P/N: B-14118)| 230 mm
8-tooth blade (P/N: B-14130)| 230 mm
Nylon cutting head (P/N: 198893-8)| 350 mm
Plastic blade (P/N: 198383-1)| 255 mm
Rated voltage| D.C. 36 V
Net weight| 4.1 – 4.7 kg| 3.9 – 4.5 kg
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge, battery adapter and charger
Battery cartridge| BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
---|---
Battery Adapter| BAP182 / BL36120A
Charger| DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / DC18SH
- Some of the battery cartridges, battery adapters and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges, battery adapters and chargers listed above. Use of any other battery cartridges ,battery adapters and chargers may cause injury and/or fire.
Noise
Applicable standard : ISO22868
Model DUR368A
Cutting tool | Sound pressure level (LpA) dB(A) | Sound power level (LWA) dB(A) |
---|---|---|
LpA dB(A) | Uncertainty (K) dB(A) | LWA dB(A) |
4-tooth blade | 74.7 | 1.0 |
Nylon cutting head | 76.4 | 1.6 |
Plastic blade | 75.1 | 0.3 |
Cutting tool | Sound pressure level (LpA) dB(A) | Sound power level (LWA) dB(A) |
--- | --- | --- |
LpA dB(A) | Uncertainty (K) dB(A) | LWA dB(A) |
4-tooth blade | 74.7 | 1.0 |
Nylon cutting head | 76.4 | 1.6 |
Plastic blade | 75.1 | 0.3 |
- Even if the sound pressure level listed above is 80 dB (A) or less, the level under working may exceed 80 dB (A). Wear ear protection.
NOTE: The declared noise emission value(s) has been measured in
accordance with a standard test method and may be used for comparing one tool
with another.
NOTE: The declared noise emission value(s) may also be used in a
preliminary assessment of exposure.
- WARNING: Wear ear protection.
- WARNING: The noise emission during actual use of the power tool can differ from the declared val-ue(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
- WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
Vibration
Applicable standard : ISO22867
Model DUR368A
Cutting tool | Left hand | Right hand |
---|---|---|
ah,W (m/s2) | Uncertainty K (m/s2) | ah,W (m/s2) |
4-tooth blade | 2.5 | 1.5 |
Nylon cutting head | 2.5 | 1.5 |
Plastic blade | 2.5 | 1.5 |
Model DUR368L
Cutting tool | Left hand | Right hand |
---|---|---|
ah,W (m/s2) | Uncertainty K (m/s2) | ah,W (m/s2) |
4-tooth blade | 2.5 | 1.5 |
Nylon cutting head | 2.5 | 1.5 |
Plastic blade | 2.5 | 1.5 |
NOTE: The declared vibration total value(s) has been measured in
accordance with a standard test method and may be used for comparing one tool
with another.
NOTE: The declared vibration total value(s) may also be used in a
preliminary assessment of exposure.
WARNING: The vibration emission during actual use of the power tool can
differ from the declared value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING: Be sure to identify safety measures to protect the operator that
are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).
Symbols
The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.
- Take particular care and attention.
- Read instruction manual.
- Keep distance at least 15 m.
- Danger; be aware of thrown objects.
- Caution; kickback
- Wear a helmet, goggles and ear protection.
- Wear protective gloves.
- Wear sturdy boots with nonslip soles. Steeled safety boots are recommended.
- Do not expose to moisture.
- Only for EU countries
Do not dispose of electric equipment or battery pack together with household waste material! In observance of the European Directives, on Waste Electric and Electronic Equipment and Batteries and Accumulators and Waste Batteries and Accumulators and their implementation in accordance with national laws, electric equipment and batteries and battery pack(s) that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A to this instruction
manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Important safety instructions for the tool
WARNING: Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
Intended use
- This tool is only intended for cutting grass, weeds, bushes and undergrowth. It should not be used for any other purpose such as edging or hedge cutting as this may cause injury.
General instructions
- Never allow people unfamiliar with these instructions, people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge to use the tool. Children should be supervised to ensure that they do not play with the tool.
- Before starting the tool, read this instruction manual to become familiar with the handling of the tool.
- Do not lend the tool to a person with insufficient experience or knowledge regarding handling of brush cutters and string trimmers.
- When lending the tool, always attach this instruction manual.
- Handle the tool with the utmost care and attention.
- Never use the tool after consuming alcohol or drugs, or if feeling tired or ill.
- Never attempt to modify the tool.
- Follow the regulations about handling of brush cutters and string trimmers in your country.
Personal protective equipment
Fig.1
- Wear safety helmet, protective goggles and protective gloves to protect yourself from flying debris or falling objects.
- Wear ear protection such as ear muffs to prevent hearing loss.
- Wear proper clothing and shoes for safe operation, such as a work overall and sturdy, non-slip shoes. Do not wear loose clothing or jewelry. Loose clothes, jewelry or long hair can be caught in moving parts.
- When touching the cutting blade, wear protective gloves. Cutting blades can cut bare hands severely.
Work area safety
- Operate the tool under good visibility and day-light conditions only. Do not operate the tool in darkness or fog.
- Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. The tool creates sparks which may ignite the dust or fumes.
- During operation, never stand on an unstable or slippery surface or a steep slope. During the cold season, beware of ice and snow and always ensure secure footing.
- During operation, keep bystanders or animals at least 15 m away from the tool. Stop the tool as soon as someone approaches.
- Never operate the tool while people, especially children, or pets are nearby.
- Before operation, examine the work area for stones or other solid objects. They can be thrown or cause dangerous kickback and result in serious injury and/or property damage.
- WARNING: Use of this product can create dust containing chemicals which may cause respiratory or other illnesses. Some examples of these chemicals are compounds found in pesticides, insecticides, fertilizers and herbicides. Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Electrical and battery safety
- Do not expose the tool to rain or wet conditions. Water entering the tool will increase the risk of electric shock.
- Do not use the tool if the switch does not turn it on and off. Any tool that cannot be con-trolled with the switch is dangerous and must be repaired.
- Prevent unintentional starting. Ensure the switch is in the off-position before installing a battery pack, picking up or carrying the tool. Carrying the tool with your finger on the switch or energizing the tool that have the switch on invites accidents.
- Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
- Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
- Do not charge battery in rain, or in wet locations.
Putting into operation
- Before assembling or adjusting the tool, remove the battery cartridge.
- Before handling the cutter blade, wear protective gloves.
- Before installing the battery cartridge, inspect the tool for damages, loose screws/nuts or improper assembly. Sharpen blunt cutter blade. If the cutter blade is bent or dam-aged, replace it. Check all control levers and switches for easy action. Clean and dry the handles.
- Never attempt to switch on the tool if it is dam-aged or not fully assembled. Otherwise serious injury may result.
- Adjust the shoulder harness and hand grip to suit the operator’s body size.
- When inserting a battery cartridge, keep the cutting attachment clear of your body and other object, including the ground. It may rotate when starting and may cause injury or damage to the tool and/or property.
- Remove any adjusting key, wrench or blade cover before turning the tool on. An accessory left attached to a rotating part of the tool may result in personal injury.
- The cutting tool has to be equipped with the guard. Never run the tool with damaged guards or without guards in place!
- Make sure there are no electrical cables, water pipes, gas pipes etc. that could cause a hazard if damaged by use of the tool.
Operation
- In the event of an emergency, switch off the tool immediately.
- If you feel any unusual condition (e.g. noise, vibration) during operation, switch off the tool and remove the battery cartridge. Do not use the tool until the cause is recognized and solved.
- The cutting attachment continues to rotate for a short period after turning the tool off. Don’t rush to contact the cutting attachment.
- During operation, use the shoulder harness. Keep the tool on your right side firmly.
- Do not overreach. Keep proper footing and balance at all times. Watch for hidden obstacles such as tree stumps, roots and ditches to avoid stumbling.
- Always be sure of your footing on slopes.
- Walk, never run.
- Never work on a ladder or tree to avoid loss of control.
- If the tool gets heavy impact or fall, check the condition before continuing work. Check the controls and safety devices for malfunction. If there is any damage or doubt, ask our authorized service center for the inspection and repair.
- Take a rest to prevent loss of control caused by fatigue. We recommend taking a 10 to 20-min-ute rest every hour.
- When you leave the tool, even if it is a short time, always remove the battery cartridge. The unattended tool with the battery cartridge installed may be used by unauthorized person and cause serious accident.
- If grass or branches get caught between the cutting attachment and guard, always turn the tool off and remove the battery cartridge before cleaning. Otherwise the cutting attachment may rotate unintentionally and cause serious injury.
- Never touch moving hazardous parts before the moving hazardous parts have come to a complete stop and the battery cartridge is removed.
- If the cutting attachment hits stones or other hard objects, immediately turn the tool off. Then remove the battery cartridge and inspect the cutting attachment.
- Check the cutting attachment frequently during operation for cracks or damages. Before the inspection, remove the battery cartridge and wait until the cutting attachment stops completely. Replace damaged cutting attachment immediately, even if it has only superficial cracks.
- Never cut above waist height.
- Before starting the cutting operation, wait until the cutting attachment reaches a constant speed after turning the tool on.
- When using a cutting blade, swing the tool evenly in half-circle from right to left, like using a scythe.
- Hold the tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring. Cutter blades contacting a “live” wire may make exposed metal parts of the tool “live” and could give the operator an electric shock.
- Do not start the tool when the cutting tool is tangled with cut grass.
- Before starting the tool, be sure that the cut-ting tool is not touching the ground and other obstacles such as a tree.
- During operation always hold the tool with both hands. Never hold the tool with one hand during use.
Cutting tools
- Do not use a cutting tool which is not recommended by us.
- Use an applicable cutting attachment for the job in hand.
- Nylon cutting heads (string trimmer heads) and plastic blades are suitable for trimming lawn grass.
- Cutting blades are suitable for cutting weeds, high grasses, bushes, shrubs, underwood, thicket, and the like.
- Never use other blades including metal multi-piece pivoting chains and flail blades. It may result in serious injury.
- Only use the cutting tool that are marked with a speed equal or higher than the speed marked on the tool.
- Always keep your hands, face, and clothes away from the cutting tool when it is rotating. Failure to do so may cause personal injury.
- Always use the cutting attachment guard properly suited for the cutting attachment used.
- When using cutting blades, avoid kickback and always prepare for an accidental kickback. See the section for Kickback.
- When not in use, attach the blade cover onto the blade. Remove the cover before operation.
Kickback (Blade thrust)
-
Kickback (blade thrust) is a sudden reaction to a caught or bound cutting blade. Once it occurs, the tool is thrown sideway or toward the operator at great force and it may cause serious injury.
-
Kickback occurs particularly when applying the blade segment between 12 and 2 o’clock to solids, bushes and trees with 3 cm or larger diameter.
Fig.2 -
To avoid kickback:
-
Apply the segment between 8 and 11 o’clock.
-
Never apply the segment between 12 and 2 o’clock.
-
Never apply the segment between 11 and 12 o’clock and between 2 and 5 o’clock, unless the operator is well trained and experienced and does it at his/her own risk.
-
Never use cutting blades close to solids, such as fences, walls, tree trunks and stones.
-
Never use cutting blades vertically, for such operations as edging and trimming hedges.
► Fig.3
Vibration
-
People with poor circulation who are exposed to excessive vibration may experience injury to blood vessels or the nervous system. Vibration may cause the following symptoms
to occur in the fingers, hands or wrists: “Falling asleep” (numbness), tingling, pain, stabbing sen-sation, alteration of skin color or of the skin. If any of these symptoms occur, see a physician! -
To reduce the risk of “white finger disease”, keep your hands warm during operation and well maintain the tool and accessories.
Transport
- Before transporting the tool, turn it off and remove the battery cartridge. Attach the cover to the cutting blade.
- When transporting the tool, carry it in a horizontal position by holding the shaft.
- When transporting the tool in a vehicle, properly secure it to avoid turnover. Otherwise damage to the tool and other baggage may result.
Maintenance
- Have your tool serviced by our authorized service center, always using only genuine replacement parts. Incorrect repair and poor maintenance can shorten the life of the tool and increase the risk of accidents.
- Before doing any maintenance or repair work or cleaning the tool, always turn it off and remove the battery cartridge.
- Always wear protective gloves when handling the cutting blade.
- Always clean dust and dirt off the tool. Never use gasoline, benzine, thinner, alcohol or the like for the purpose. Discoloration, deformation or cracks of the plastic components may result.
- After each use, tighten all screws and nuts.
- Do not attempt any maintenance or repair not described in the instruction manual. Ask our authorized service center for such work.
- Always use our genuine spare parts and accessories only. Using parts or accessories supplied by a third party may result in the tool breakdown, property damage and/or serious injury.
- Request our authorized service center to inspect and maintain the tool at regular interval.
- Always keep the tool in good working condition. Poor maintenance can result in inferior performance and shorten the life of the tool.
Storage
- Before storing the tool, perform full cleaning and maintenance. Remove the battery car-tridge. Attach the cover to the cutting blade.
- Store the tool in a dry and high or locked location out of reach of children.
- Do not prop the tool against something, such as a wall. Otherwise it may fall suddenly and cause an injury.
First aid
- Always have a first-aid kit close by. Immediately replace any item taken from the first aid kit.
- When asking for help, give the following information:
- Place of the accident
- What happened
- Number of injured persons
- Nature of the injury
- Your name
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
Important safety instructions for battery cartridge
-
Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
-
Do not disassemble battery cartridge.
-
If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
-
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
-
Do not short the battery cartridge:
-
Do not touch the terminals with any conductive material.
-
Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
-
Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns and even a breakdown. -
Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
-
Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
-
Be careful not to drop or strike battery.
-
Do not use a damaged battery.
-
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirement on pack-aging and labeling must be observed.
For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations.
Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. -
When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.
-
Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.
-
If the tool is not used for a long period of time, the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita
batteries, or batteries that have been altered, may result in the battery
bursting causing fires, personal injury and damage. It will also void the
Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
- Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
- Charge the battery cartridge with room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
- Charge the battery cartridge if you do not use it for a long period (more than six months).
PARTS DESCRIPTION
Fig.4
1| Speed indicator| 2| ADT indicator (ADT = Automatic Torque Drive
Technology)| 3| Power lamp| 4| Main power button
---|---|---|---|---|---|---|---
5| Reverse button| 6| Battery cartridge| 7| Lock-off lever| 8| Switch trigger
9| Hanger| 10| Handle| 11| Barrier (country specific)| 12| Protector (for
nylon cutting head / plastic blade)
13| Protector (for cutter
blade)
| 14| Shoulder harness| –| –| –| –
FUNCTIONAL DESCRIPTION
WARNING: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Failure to switch off and remove the battery cartridge may result in serious personal injury from accidental start-up.
Installing or removing battery cartridge
- CAUTION: Always switch off the tool before installing or removing of the battery cartridge.
- CAUTION: Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.
Fig.5:
- Red indicator
- Button
- Battery cartridge
To remove the battery cartridge, slide it from the tool while sliding the
button on the front of the cartridge.
To install the battery cartridge, align the tongue on the battery cartridge
with the groove in the housing and slip it into place. Insert it all the way
until it locks in place with a little click. If you can see the red indicator
on the upper side of the button, it is not locked completely.
CAUTION: Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
Tool / battery protection system
The tool is equipped with a tool/battery protection system. This system
automatically cuts off power to the motor to extend tool and battery life. The
tool will automatically stop during operation if the tool or battery is placed
under one of the following conditions:
Overload protection
If the tool is overloaded by entangled weeds or other debris, the speed
indicator 2 and 3 start blinking and the tool automatically stops. In this
situation, turn the tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.
Overheat protection for tool or battery
There are two types of overheating; tool overheating and battery overheating.
When the tool overheating occurs, all speed indicators blink. When the battery
overheating occurs, the speed indicator 1 blinks.
If the overheating occurs, the tool stops automatically. Let the tool and/or
battery cool down before turning the tool on again.
Over discharge protection
When the battery capacity becomes low, the tool stops automatically and the
speed indicator 1 blinks.
If the tool does not operate even when the switches are operated, remove the
batteries from the tool and charge the batteries.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.6:
- Indicator lamps
- Check button
Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for a few seconds.
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
Main power switch
Tap the main power button to turn on the tool.
To turn off the tool, press and hold the main power but-ton until the power
lamp and speed indicator go off.
Fig.7:
- Speed indicator
- Main power button
- Power lamp
NOTE: The tool will automatically turned off if it is left without any operations for a certain period of time.
Switch action
WARNING: For your safety, this tool is equipped with lock-off lever which
prevents the tool from unintended starting. NEVER use the tool if it runs when
you simply pull the switch trigger without pressing the lock-off lever. Return
the tool to our authorized service center for proper repairs BEFORE further
usage.
WARNING: NEVER tape down or defeat purpose and function of lock-off
lever.
CAUTION: Before installing the battery car-tridge into the tool, always
check to see that the switch trigger actuates properly and returns to the
“OFF” position when released. Operating a tool with a switch that does not
actuate properly can lead to loss of control and serious personal injury.
CAUTION: Never put your finger on the main power button and switch
trigger when carrying the tool. The tool may start unintentionally and cause
injury.
NOTICE: Do not pull the switch trigger hard with-out pressing the lock-
off lever. This can cause switch breakage.
To prevent the switch trigger from being accidentally pulled, a lock-off lever
is provided. To start the tool, depress the lock-off lever and pull the switch
trigger. The tool speed increases by increasing pressure on the switch
trigger. Release the switch trigger to stop.
DUR368A
Fig.8:
- Lock-off lever
- Switch trigger
DUR368L
Fig.9:
- Lock-off lever
- Switch trigger
Speed adjusting
You can adjust the tool speed by tapping the main power button. Each time
you tap the main power button, the level of speed will change.
Fig.10:
- Speed indicator
- Main power button
Automatic Torque Drive Technology
When you turn on the Automatic Torque Drive Technology (ADT), the tool runs at
optimum rotation speed and torque for the condition of grass being cut.
To start ADT, press and hold the reverse button until the ADT indicator turns
on. After that, tap the main power button to select the cutting tool attached
to the tool. Light the lamp beside marking to select cutter blade and plastic
blade, marking to select nylon cutting head. To stop ADT, press and hold the
reverse button until the ADT indicator turns off.
► Fig.11:
- marking
- marking
- ADT indicator
- Main power button
- Reverse button
Reverse button for debris removal
WARNING: Switch off the tool and remove the battery cartridge before you
remove entangled weeds or debris which the reverse rotation function can not
remove. Failure to switch off and remove the battery cartridge may result in
serious personal injury from accidental start-up.
This tool has a reverse button to change the direction of rotation. It is only
for removing weeds and debris entangled in the tool. To reverse the rotation,
tap the reverse button and pull the trigger when the cutting tool is stopped.
The power lamp starts blinking, and the cutting tool rotates in reverse
direction when you pull the switch trigger.
To return to regular rotation, release the trigger and wait until the cutting
tool stops.
Fig.12:
- Reverse button
- Power lamp
NOTE: During the reverse rotation, the tool operates only for a short
period of time and then automatically stops.
NOTE: Once the tool is stopped, the rotation returns to regular direction
when you start the tool again.
NOTE: If you tap the reverse button while the cutting tool is still
rotating, the tool comes to stop and to be ready for reverse rotation.
Electric brake
This tool is equipped with an electric brake for the cut-ting tool. If the
tool consistently fails to quickly stop the cutting tool after the switch
trigger is released, have the tool serviced at our service center.
CAUTION: This brake system is not a substitute for the protector. Never use the tool without the protector. An unguarded cutting tool may result in serious personal injury.
Electronic function
-
Constant speed control
The speed control function provides the constant rotation speed regardless of load conditions. -
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
WARNING: Always be sure that the tool is switched off and battery
cartridge is removed before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result in serious personal
injury from accidental start-up.
WARNING: Never start the tool unless it is completely assembled.
Operation of the tool in a partially assembled state may result in serious
personal injury from accidental start-up.
Installing the handle
For DUR368A
-
Insert the shaft of the handle into the grip. Align the screw hole in the grip with the one in the shaft. Tighten the screw securely.
Fig.13: -
Grip
-
Screw
-
Shaft
NOTICE: Note the direction of the grip. The screw holes will not be aligned if the grip is not inserted in the correct direction.
-
Place handle between handle clamp and handle holder. Adjust the handle to an angle that provides a comfortable working position and then secure with hex socket head bolts.
► Fig.14: -
Hex socket head bolt
-
Handle clamp
-
Handle holder
For DUR368L
-
Attach the upper and lower clamps on the damper.
-
Pu tthe handle on the upper clamp and fix it with hex socket head bolts as illustrated.
Fig.15: -
Hex socket head bolt
-
Handle 3. Upper clamp
-
Damper 5. Lower clamp
-
Spacer
CAUTION: Do not remove or shrink the spacer. Doing so lose the balance of the tool and may cause personal injury.
Attaching the barrier
Country specific
If the barrier is included in your model, attach it to the handle using the
screw on the barrier.
Fig.16:
- Barrier
- Screw
CAUTION: After assembling the barrier, do not remove it. The barrier works as a safety part to prevent you from contacting the cutting blade accidentally.
Hex wrench storage
CAUTION: Be careful not to leave the hex wrench inserted in the tool head.
It may cause injury and/or damage to the tool.
When not in use, store the hex wrench as illustrated to keep it from being
lost.
Fig.17: 1. Hex wrench
For the loop handle model, the hex wrench can also be stored on the handle as
illustrated.
Fig.18: 1. Hex wrench
Correct combination of the cutting tool and the protector
CAUTION: Always use the correct combination of cutting tool and the
protector. A wrong combination may not protect you from the cutting tool,
flying debris, and stones. It can also affect the balance of the tool and
result in an injury.
Installing the protector
WARBNING: Never use the tool without the guard illustrated in place.
Failure to do so can cause serious personal injury.
NOTE: The type of the protector supplied as the standard accessory varies
depending on the countries.
For cutter blade
Attach the protector to the clamp using bolts.
Fig.19:
- Clamp
- Protector
For nylon cutting head / plastic blade
CAUTION: Take care not to injure yourself on the cutter for cutting the
nylon cord.
Attach the protector to the clamp using bolts.
Fig.20:
- Clamp
- Protector
- Cutter
Installing the cutting tool
CAUTION: Always use the supplied wrench(es) to remove or to install the
cutting tool.
CAUTION: Be sure to remove the hex wrench inserted into the tool head
after installing the cutting tool.
NOTE: The type of the cutting tool(s) supplied as the standard accessory
varies depending on the counties. The cutting tool is not included in some
specifications of the model.
NOTE: Turn the tool upside down so that you can replace the cutting tool
easily.
Cutter blade
CAUTION: When handling the cutter blade, always wear gloves and put the
blade cover on the blade.
CAUTION: The cutter blade must be well poished, and free of cracks or
breakage. If the cutter blade hits a stone during operation, stop the tool and
check the blade immediately.
CAUTION: The cutter blade-fastening nut
(with spring washer) wears out in course of time. If there appears any wear or
deformation on the spring washer, replace the nut. Ask your local authorized
service center to order it.
CAUTION: The outside diameter of the cutter blade must be as follows.
Never use any cutter blade with larger outside diameter.
- 3-tooth blade : 230 mm
- 4-tooth blade : 230 mm
- 8-tooth blade : 230 mm
► Fig.21:
-
Nut
-
Clamp washer
-
Cutter blade
-
Receive washer
-
Spindle
-
Hex wrench
-
Insert the hex wrench through the hole in the tool head to lock the shaft. Rotate the shaft until the hex wrench is fully inserted.
-
Mount the cutter blade onto the receive washer so that the arrows on the blade and protector are pointing in the same direction.
Fig.22: -
Arrow
-
Put the clamp washer onto the cutter blade and then tighten the nut securely by the box wrench.
Fig.23: -
Hex wrench
-
Box wrench
-
Tighten
-
Loosen
NOTE: Tightening torque : 16 – 23 N•m -
Remove the hex wrench from the tool head.
To remove the cutter blade, follow the installation procedures in reverse.
Nylon cutting head
NOTICE: Be sure to use genuine Makita nylon cutting head.
► Fig.24:
-
Nylon cutting head
-
Receive washer
-
Spindle
-
Hex wrench
-
Tighten
-
Loosen
-
Insert the hex wrench through the hole in the tool head to lock the shaft. Rotate the shaft until the hex wrench is fully inserted.
-
Place the nylon cutting head onto the spindle and tighten it securely by hand.
-
Remove the hex wrench from the tool head.
To remove the nylon cutting head, follow the installation procedures in reverse.
Plastic blade
NOTICE: Be sure to use genuine Makita plastic blade.
► Fig.25:
-
Plastic blade
-
Receive washer
-
Spindle
-
Hex wrench
-
Tighten
-
Loosen
-
Insert the hex wrench through the hole in the tool head to lock the shaft. Rotate the shaft until the hex wrench is fully inserted.
-
Place the plastic blade onto the spindle and tighten it securely by hand.
-
Remove the hex wrench from the tool head.
To remove the plastic blade, follow the installation procedures in reverse.
OPERATION
Attaching the shoulder harness
CAUTION: Always use the shoulder harness attached to the tool. Before
operation, adjust the shoulder harness according to the user size to prevent
fatigue.
CAUTION: Before operation, make sure that the shoulder harness is
properly attached to the hanger on the tool.
-
Wear the shoulder harness on your left shoulder.
Fig.26 -
Clasp the hook on the shoulder strap to tool’s hanger.
DUR368A
Fig.27: -
Hook
-
Hanger
DUR368L
Fig.28:
3. Hook
4. Hanger
- Adjust the shoulder harness to a comfortable working position.
Fig.29
The shoulder harness features a means of quick release.
Simply squeeze the sides of the buckle to release the tool from the shoulder
harness.
DUR368A
Fig.30:
- Buckle
DUR368L
Fig.31:
- Buckle
Adjusting the hanger position
For more comfortable handling of the tool, you can change the hanger position.
Be sure to adjust the hanger position as shown in the figure.
Fig.32
1 | The hanger position from the ground |
---|---|
2 | The cutting tool position from the ground |
3 | The horizontal distance between the hanger and the unguarded part of the |
cutting tool
Loosen the hex socket head bolt on the hanger. Move the hanger to a
comfortable working position and then tighten the bolt.
DUR368A
► Fig.33:
- Hanger
- Hex socket head bolt
DUR368L
► Fig.34:
- Hanger
- Hex socket head bolt
Correct handling of the tool
WARNING: Always position the tool on your right-hand side. Correct
positioning of the tool allows for maximum control and will reduce the risk of
seri-ous personal injury caused by kickback.
WARNING: Be extremely careful to maintain control of the tool at all
times. Do not allow the tool to be deflected toward you or anyone in the work
vicinity. Failure to keep control of the tool could result in serious injury
to the bystander and the operator.
WARNING: To avoid accident, leave more than 15m (50 ft) distance between
operators when two or more operators work in one area. Also, arrange a person
to observe the distance between operators. If someone or an animal enters the
working area, immediately stop the operation.
CAUTION: If the cutting tool accidentally impacts a rock or hard object
during operation, stop the tool and inspect for any damage. If the cutting
tool is damaged, replace it immediately. Use of a damaged cutting tool may
result in serious personal injury.
CAUTION: Remove the blade cover from the cutter blade when cutting the
grass.
Correct positioning and handling allow optimum control and reduce the risk of
injury caused by kickback.
DUR368A
Fig.35
DUR368L
Fig.36
When using a nylon cutting head (bump & feed type)
The nylon cutting head is a dual string trimmer head provided with a bump &
feed mechanism.
To feed out the nylon cord, tap the cutting head against the ground while
rotating.
Fig.37:
- Most effective cutting area
NOTICE: The bump feed will not operate properly if the nylon cutting head
is not rotating.
NOTE: If the nylon cord does not feed out while tapping the head,
rewind/replace the nylon cord by following the procedures in the section for
the maintenance.
MAINTENANCE
WARNING: Always be sure that the tool is switched off and battery
cartridge is removed before attempting to perform inspection or maintenance on
the tool. Failure to switch off and remove the battery cartridge may result in
serious personal injury from accidental start-up.
NOTICE: Never use gasoline, benzine, thinner, alcohol or the like.
Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Replacing the nylon cord
WARNING: Use only the nylon cord with diameter specified in this
instruction manual. Never use heavier line, metal wire, rope or the like.
Failure to do so may cause damage to the tool and result in serious personal
injury.
WARNING: Always remove the nylon cutting head from the tool when
replacing the nylon cord.
WARNING: Make sure that the cover of the nylon cutting head is secured to
the housing properly as described below. Failure to properly secure the cover
may cause the nylon cutting head to fly apart resulting in serious personal
injury.
Replace the nylon cord if it is not fed any more. The method of replacing the
nylon cord varies depending on the type of the nylon cutting head.
95-M10L
► Fig.38
B&F ECO 4L
► Fig.39
For Ultra Auto 4
► Fig.40
UN-74L
► Fig.41
Manual feed type
When the nylon cord gets short, pull it out from the eyelet and feed it from
the another eyelet.
► Fig.42
Replacing the plastic blade
Replace the blade if it is worn out or broken.
Fig.43
When installing the plastic blade, align the direction of the arrow on the
blade with that of the protector.
Fig.44:
- Arrow on the protector
- Arrow on the blade
TROUBLESHOOTING
Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.
State of abnormality| Probable cause (malfunction)|
Remedy
---|---|---
Motor does not run.| Battery cartridge is not installed.| Install the battery
cartridge.
Battery problem (under voltage)| Recharge the battery. If recharging is not
effective, replace battery.
The drive system does not work
correctly.
| Ask your local authorized service center for repair.
Motor stops running after a little use.| Battery’s charge level is low.|
Recharge the battery. If recharging is not effective, replace battery.
Overheating.| Stop using of tool to allow it to cool down.
It does not reach maximum RPM.| Battery is installed improperly.| Install the
battery cartridge as described in this manual.
Battery power is dropping.| Recharge the battery. If recharging is not
effective, replace battery.
The drive system does not work correctly.| Ask your local authorized service
center for repair.
Cutting tool does not rotate:
stop the machine immediately!
| Foreign object such as a branch is jammed between the guard and the cutting
tool.| Remove the foreign object.
The drive system does not work correctly.| Ask your local authorized service
center for repair.
Abnormal vibration:
stop the machine immediately!
| One end of the nylon cord has been broken.| Tap the nylon cutting head
against the ground while it is rotating to cause the cord to feed.
The drive system does not work correctly.| Ask your local authorized service
center for repair.
Cutting tool and motor cannot stop: Remove the battery immediately!| Electric
or electronic malfunction.| Remove the battery and ask your local authorized
service center for repair.
OPTIONAL ACCESSORIES
WARNING: Only use the recommended accessories or attachments indicated in this manual. The use of any other accessory or attachment may result in serious personal injury.
CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
- Cutter blade
- Nylon cutting head
- Nylon cord (cutting line)
- Plastic blade
- Protector
- Makita genuine battery and charger
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>