makita GLC03 Cordless Cleaner Instruction Manual
- June 10, 2024
- Makita
Table of Contents
- SPECIFICATIONS
- SAFETY WARNINGS
- ADDITIONAL SAFETY RULES
- Symbols
- Important safety instructions for battery cartridge
- FUNCTIONAL DESCRIPTION
- Battery protection system
- Switch action
- Lighting up the lamp
- PARTS DESCRIPTION
- ASSEMBLY
- OPERATION
- MAINTENANCE
- Troubleshooting
- OPTIONAL ACCESSORIES
- MAKITA LIMITED WARRANTY
- Documents / Resources
INSTRUCTION MANUAL
Cordless
Cleaner
GLC03
IMPORTANT: Read Before Using.
SPECIFICATIONS
Model: | GLCO3 |
---|---|
Capacity | 250 mL (0.07 gal.) |
Continuous use
(with battery BL4025)| 1 (Quiet mode)| Approx. 80 min
2 (Normal speed mode)| Approx. 40 min
3 (High speed mode)| Approx. 25 min
4 (Max speed mode)| Approx. 16 min
Overall length (with pipe, nozzle, and battery BL4025)| 1,106 mm (43-1/2″)
Rated voltage| D.C. 36 V – 40 V max
Net weight| 1.9 – 2.6 kg (4.2 – 5.7 Ibis)
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight of the appliance and battery cartridge(s) are shown in the table.
Applicable battery cartridge and charger
Battery cartridge| BL4020 / BL4025 / BL4040 / BL4050F : Recommended
battery
---|---
Charger| DC40RA / DC40RB / DC40RC
• Some of the battery cartridges and chargers listed above may not be
available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use
of any other battery cartridges and chargers may cause injury and/or fire.
SAFETY WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING
To reduce the risk of fire, electric shock or injury:
- Do not leave appliance when battery fitted. Remove battery from appliance when not in use and before servicing.
- Do not use on wet surfaces. Do not expose to rain. Store indoors.
- Do not allow to be used as a toy. Close attention is necessary when used by or near children.
- Use only as described in this manual. Use only manufacturer’s recommended attachments.
- Do not use with damaged battery. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
- Do not handle appliance with wet hands.
- Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
- Turn off all controls before removing the battery cartridge.
- Use extra care when cleaning on stairs.
- Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not use without dust bag and/or filters in place.
- Do not charge the battery outdoors.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.
- Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
- Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
- Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. 25. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.
AVE THESE INSTRUCTIONS.
ADDITIONAL SAFETY RULES
This appliance is intended for commercial use.
-
Read this instruction manual and the charger instruction manual carefully before use.
-
Do not vacuum the following:
• Flammable liquid (kerosene, gasoline, solvents such as benzine, thinner, etc.)
• Hot substances that are burning or smoking (cigarettes, matches, incense sticks, candles, hot ashes), sparks and metal dust generated by cutting or grinding metal, etc.
• Flammable material (toner, paint, spray, etc.)
• Foam like carpet cleaning agent, etc.(they may cause explosion or fire)
• Explosive or pyrophoric substances (nitroglycerin, aluminum, magnesium, titanium, zinc,red phosphorus, yellow phosphorus, celluloid, etc. and their dust, gas or steam)
• Sharp objects (glass, cutlery, wood splinter, metal, stone, nail, razor, push pin, etc.)
• Solidifying and conductive fine powder (metal or carbon powder)
• Dehumidifier
• Large amount of powder (flour, fire extinguisher powder, etc.)
• Substances that cause toxic symptoms
• Aggressive chemicals (acid, leach, etc.)
• Liquid or damp garbage, including vomit and excreta
• Asbestos
• Pesticides Such action may cause fire, injury and/or property damage. To reduce your exposure to these chemicals, always wear approved respiratory protection such as dust masks that are specially designed to filter out microscopic particles. Direct the exhaust air away from your face and body. -
Stop operation immediately if you notice anything abnormal.
-
If you drop or strike the cleaner, check it carefully for cracks or damage before operation.
-
Do not bring close to stoves or other heat sources.
-
Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.
Symbols
The followings show the symbols used for tool.
V | volts |
---|---|
**** | direct current |
Important safety instructions for battery cartridge
- Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
- Do not disassemble or tamper the battery cartridge. It may result in a fire, excessive heat, or explosion.
- If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
- If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
- Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
- Do not store and use the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
- Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
- Do not nail, cut, crush, throw, drop the battery cartridge, or hit against award object to the battery cartridge. Such conduct may result in a fire, excessive heat, or explosion.
- Do not use a damaged battery.
- The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirement on packaging and labeling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging.
- When disposing the battery car- trudge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery.
- Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte.
- If the tool is not used for a long period of time, the battery must be removed from the tool.
- During and after use, the battery cartridge may take on heat which can cause burns or low temperature burns. Pay attention to the handling of hot battery cartridges.
- Do not touch the terminal of the tool immediately after use as it may get hot enough to cause burns.
- Do not allow chips, dust, or soil stuck into the terminals, holes, and grooves of the battery cartridge. It may result in poor performance or breakdown of the tool or battery cartridge.
- Unless the tool supports the use near high-voltage electrical power lines, do not use the battery cartridge near a high-voltage electrical power lines. It may result in a malfunction or breakdown of the tool or battery cartridge.
- Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
- Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
- Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
- Charge the battery cartridge with room temperature at 10 °C – 40 °C (50 °F – 104 °F). Let a hot battery cartridge cool down before charging it.
- When not using the battery cartridge, remove it from the tool or the charger.
- Charge the battery cartridge if you do not use it for a long period (more than six months).
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before adjusting or checking function on the tool.
CAUTION: Take care not to trap finger(s) between cleaner and battery as
shown in diagram when loading battery. Trapping finger(s) may cause injury.
Installing or removing battery cartridge
CAUTION: Always switch off the tool before installing or removing of the
battery cartridge.
CAUTION: Hold the tool and the battery cartridge firmly when installing
or removing battery cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands and result in damage to
the tool and battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool while sliding the
button on the front of the cartridge.
To install the battery cartridge, align the tongue on the battery cartridge
with the groove in the housing and slip it into place. Insert it all the way
until it locks in place with a little click. If you can see the red indicator
as shown in the figure, it is not locked completely.
CAUTION: Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
CAUTION: Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
Battery protection system
The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions.
Overloaded:
The tool/battery is operated in a manner that causes it to draw an abnormally
high current.
In this situation, turn the tool off and stop the application that caused the
tool to become overloaded. Then turn the tool on to restart.
If the tool does not start, the tool/battery is overheated.
In this situation, let the tool/battery cool before turning the tool on again.
Low battery voltage:
The remaining battery capacity is too low and the tool will not operate. In
this situation, remove and recharge the battery.
Protections against other causes:
Protection system is also designed for other causes that could damage the tool
and allows the tool to stop automatically. Take all the following steps to
clear the causes, when the tool has been brought to a temporary halt or stop
in operation.
- Turn the tool off, and then turn it on again to restart.
- Charge the battery(is) or replace it/them with recharged battery(is).
- Let the tool and battery(is) cool down.
If no improvement can be found by restoring protection system, then contact your local Makita Service Center.
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indicate the remaining
battery capacity.
The indicator lamps light up for a few seconds.
Indicator lamps | Remaining capacity |
---|---|
Lighted | Off |
75% to 100% | |
50% to 75% | |
25% to 50% | |
0% to 25% | |
Charge the |
battery.
| The battery may have malfunctioned.
NOTE: Depending on the conditions of use and the ambient temperature, the
indication may differ slightly from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when the battery
protection system works.
Switch action
► 1. Suction power change button 2. ON/OFF button
To start the cleaner, simply push the ON/OFF button. To switch off, push the
ON/OFF button again.
You can change the suction power of the cleaner in four steps by pushing the
suction power change button.
Each push on this button repeats the Quiet/Normal/ High/Max mode in a cycle.
Level | Indication | Mode |
---|---|---|
1 | Quiet mode | |
2 | Normal speed mode | |
3 | High speed mode | |
4 | Max speed mode |
NOTE: You can change the suction power before turning on the cleaner.
NOTE: The cleaner starts the operation with the same suction power as the
last operation.
Lighting up the lamp
CAUTION: Do not look in the light or see the source of light directly.
To turn on the lamp, push the suction power change button. The lamp goes off
in approximately 10 seconds.
While the cleaner is running, the lamp turns on.
The lamp goes out approximately 10 seconds after stopping operation.
NOTE: When the remaining battery capacity gets low, the lamp starts
blinking. The timing, at which the lamp starts blinking depends on the
temperature at work place and the battery cartridge conditions.
PARTS DESCRIPTION
1| 250 mL (0.07 gal.) dust case| 2| Mesh filter| 3| Cyclone body| 4| High
performance filter (Filter frame in gray color) (Optional accessory)
---|---|---|---|---|---|---|---
5| HEPA filter (Filter frame in white color) (Optional accessory)| 6| Sponge
sheet| 7| Cleaner body| 8| Hand strap (Country specific)
ASSEMBLY
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before carrying out any work on the tool.
NOTICE: Make sure all the attachments and components are secured in place
properly before use.
Installing and removing cleaner attachments
CAUTION: After installing attachments, check if they are securely installed.
If the attachments are installed imperfectly, they may come off and cause
personal injury.
CAUTION: Be careful not to hit your hand on the wall etc. when removing
the attachments.
When using attachment with lock function
To install attachment, insert it to the suction inlet of the cleaner until it
clicks. Make sure that the attachment is locked.
NOTICE: When installing the attachment with lock function, be sure to
align the release button on the cleaner with the hook on the attachment. If
they are not aligned, the attachment will not be locked and may come off from
the cleaner.
To remove attachment, pull it off the cleaner while pressing and holding the
arms of the release button.
- Release button
- Arm of release button
- Attachment with lock function
- Suction inlet
When using attachment without lock function
NOTICE: To install attachment without lock function, insert it into the
suction inlet of the cleaner by twisting it as shown in the figure. To detach
attachment, release it from the cleaner by twisting it as shown in the figure.
Avoid twisting the attachment in the direction opposite to the arrow in the
figure as it may loosen the cyclone unit.
OPERATION
CAUTION: Do not move your face close to the air vent when operating the
cleaner. If foreign objects are blown into eyes, it may result in personal
injury.
NOTICE: Avoid using the cleaner in a horizontal or upward facing
position. It may otherwise cause the mesh filter to become clogged.
NOTICE: Always use the cleaner with filters installed. Using the cleaner
without filters may result in a motor malfunction.
NOTICE: Empty the dust case in the cyclone unit when dust has
accumulated. Continued use will result in weakened suction force.
The cyclone unit helps reduce the amount of dust that enters into the cleaner,
enhancing the suction performance with simple and easy dust disposing.
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture, etc. The nozzle slips
on easily.
Nozzle + Extension wand (Straight pipe)
The extension wand fits in between the nozzle and the cleaner itself. This
arrangement is convenient for cleaning a floor in a standing position.
Corner nozzle
Fit on the corner nozzle for cleaning corners and crevices of a car or
furniture.
You can store the corner nozzle in the nozzle holder.
CAUTION: Be careful not to trap finger(s) between the corner nozzle and
the nozzle holder.
Trapping finger(s) may cause injury.
Corner nozzle + Extension wand (Straight pipe)
In tight quarters where the cleaner itself cannot squeeze in, or in high
places hard to reach, use this arrangement.
Cleaning without nozzle
You can pick up powder and dust without nozzle.![makita GLC03 Cordless Cleaner
- fig 15](https://manuals.plus/wp-content/uploads/2023/05/makita-GLC03 -Cordless-Cleaner-fig-15.jpg)
For picking up dust on a floor in a standing position, it is convenient to attach the extension wand (straight pipe) to the cleaner.
Disposing of dust
CAUTION: Empty the dust case before it becomes too full, or the suction
force weakens.
CAUTION: Be careful not to trap finger(s) between the dust case and
cyclone body when reassembling.
Dispose of accumulated dust as follows before it exceeds the dust disposal
line.
- Point the cleaner head downwards, hold the dust case firmly, and then pull it apart from the cyclone body while pressing and holding the release buttons on both sides of the dust case.
- Empty the dust case and clean the adhered dust off the mesh filter.
- 3. Place the dust case back onto the cyclone body to secure it in place with clicks.
CAUTION: The dust may fly up when disposed out of the dust case. Be
careful not to let the dust get into your eyes.
NOTICE: When the dust case becomes dirty, remove and wash it with water.
Dry the dust case thoroughly before reassembly and use.
NOTICE: Make sure all the attachments and components are secured in place
properly before use.
NOTICE: If the suction force does not recover even after disposing of the
dust and cleaning the mesh filter, check whether dust has accumulated inside
the cyclone body or clogging has occurred.
MAINTENANCE
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before attempting to perform inspection or maintenance.
NOTICE: Never use gasoline, benzine, thinner, alcohol or the like.
Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
After use
CAUTION: Putting the cleaner against the wall without any other support may
cause the cleaner to fall down, resulting in personal injury or damage to the
cleaner.
Regular maintenance
NOTICE: Clean the filters in the cyclone unit when they become clogged.
Continued use in the clogged condition may result in heating or motor
malfunction.
NOTICE: Do not blow dust sticking on the cleaner and filters by air
duster. It brings dust into the housing and causes failure.
Routine maintenance is required to restore normal operating conditions.
Cleaner body
Wipe off the outside (cleaner body) of the cleaner using a cloth dampened in
soapy water, and clean out the suction openings.
Cyclone unit and filters
NOTICE: Dust off and clean out inside the cyclone unit and filters, when
suction performance becomes less effective regardless of the amount of dust
collected in the dust case.
NOTICE: After washing filters, dry them thor- oughly before use.
Insufficiently dried filters may cause poor suction and shorten the service
life of the motor.
NOTICE: After cleaning filters and sponge sheet, be sure to re-install
them before use. If you use the cleaner without filters and sponge sheet, dust
comes into the motor housing and causes malfunction.
Cyclone unit
- Tap the cyclone unit several times with your hand to remove dust adhering to the inner surface of the cyclone unit and filter.
- With the suction inlet pointing downwards, turn the cyclone unit as shown in the figure aligning the pointer on the cyclone unit with that on the cleaner body to disengage the lock. Then detach the cyclone unit from the cleaner body slowly and straightly. NOTE: Dust may fly out when the cyclone unit is disassembled. It is recommended to place a garbage bag underneath the cyclone unit.
- Dust off inside the cyclone unit and filter.
- Place the cyclone unit back onto the cleaner body, aligning the pointer on the cyclone unit with that on the cleaner body. Then turn the cyclone unit as shown in the figure until it is secured in place.
High performance filter
Optional accessory
- Disassemble the cyclone unit from the cleaner body.
- Hold the mounting end of high performance filter and pull it apart from the cleaner body.
- Wipe and shake dust off the high performance filter by hand.
- Wash the high performance filter in soapy water when it is clogged with dust and dirt. Dry it out thoroughly in the shade before use. NOTE: Avoid fastening the attachment end (rubber sealing ring) of high performance filter when hanging it up for drying.
- Hold the mounting end of high performance filter and squeeze it back into the cleaner body.
HEPA filter
Optional accessory
NOTICE: Do not rub or scratch the HEPA filter with hard objects such as a
brush and a paddle.
- Disassemble the cyclone unit from the cleaner body.
- Hold the mounting end of HEPA filter (covered with high performance refilter) and pull it apart from the .0cleaner body.
- Disassemble the high performance refilter from the HEPA filter by hand twisting.
- Wipe and shake dust off the high performance profiler and HEPA filter by hand.
- Wash the high performance refilter and HEPA filter in soapy water. Rinse and dry them thoroughly in the shade before use. NOTE: Avoid fastening the attachment end (rubber sealing ring) of HEPA filter when hanging it up for drying.
- Attach the high performance refilter onto the HEPA filter.
- Hold the mounting end of HEPA filter (covered with high performance refilter) and squeeze it back into the cleaner body.
Sponge sheet
- Disassemble the cyclone unit from the cleaner body.
- Hold the mounting end of filter and pull it apart from the cleaner body.
- Pull the sponge sheet off from the suction opening.
- Wipe and shake dust off the sponge sheet by hand.
- Wash the sponge sheet in soapy water when it is clogged with dust and dirt. Dry it out thoroughly in the shade before use.
- Place the sponge sheet back in the original position. Make sure that the left and right edges of the sponge sheet are secured with stoppers and no gap between the sponge sheet and suction opening.
- Hold the mounting end of filter and squeeze it back into the cleaner body.
Condition-based maintenance
NOTICE: Clean the mesh filter in the cyclone unit when they become clogged.
Continued use in the clogged condition may result in heating or motor
malfunction.
Deep and spot cleaning needs to be carried out according to your tool
performance.
Mesh filter
Clean up the mesh filter placed in the cyclone unit when no suggested
improvement on suction performance has been found after completing regular
maintenance.
-
Hold the dust case firmly and pull it apart from the cyclone body while pressing and holding the release buttons on both sides of the dust case.
-
Turn the mesh filter as shown in the figure to disengage the lock.
Then detach it from the cyclone body. -
Disassemble the mesh filter into three components: refilter, tubular sponge filter and mesh pipe.
i Squeeze the guide stoppers on top of the mesh pipe together.
ii Pass the guide stoppers down through the guide hole on top of the refilter.
iii Pull the the refilter along the tubular sponge filter and mesh pipe.
iv Remove the tubular sponge filter from the mesh pipe. -
Wipe and shake dust off the filters and mesh pipe by hand.
-
Wash the filters and mesh pipe in soapy water when they are clogged with dust and dirt. Dry them out thoroughly in the shade before use.
-
Reassemble the mesh filter.
i Insert the tubular sponge filter into the refilter.
ii Insert the mesh pipe into the tubular sponge filter and refilter, passing the guide stoppers on top of the mesh pipe through the guide hole on top of the refilter.
iii Push the mesh pipe through the tubular sponge filter and refilter until it lock in place with a click. -
Attach the mesh filter back into the cyclone body aligning the hooks on the mesh filter with the ports on the suction outlet of the cyclone body. Turn the mesh filter as shown in the figure until the hooks are locked with a click. Make sure that the mesh filter is installed securely.
Air channels in cyclone unit
Incoming foreign substance may block the air channels in the cyclone unit and
laden air flows. Remove any obstacles in the air path if the suction
performance is being affected remarkably.
-
Disassemble the cyclone unit into three components: dust case, mesh filter and cyclone body.
-
Press and hold the guide stopper on the inlet pipe down through the locking hole on the cyclone body using the hand tool with a point. Then detach the inlet pipe from the cyclone body.
-
Clean off any substance found in the air channels.
Foreign substance is likely to get stuck around an incoming air port. -
Insert the inlet pipe back in place until it is securely locked.
NOTICE: Be sure that the O-ring and flap valve are securely in place before reassembly. Suction performance can be affected if the cyclone unit is operated without the O-ring and flap valve in place. -
Reassemble the cyclone unit, and attach it onto the cleaner body.
Troubleshooting
Before asking for repairs, check the following points.
Symptom | Area to be investigated | Fixing method |
---|---|---|
Weak suction power | Is dust case or inside cyclone unit full of dust? | Empty |
dust case or inside cyclone unit.
Are filters clogged?| Dust down or wash high performance filter/HEPA
filter/sponge sheet/mesh filter.
Anything to block incoming air channels?| Clean any dust and objects out of
air openings and channels.
Is battery cartridge discharged?| Charge battery cartridge.
Not working| Is battery cartridge discharged?| Charge battery cartridge.
Noise and vibration| Are filters clogged?| Dust down or wash high performance
filter/HEPA filter/sponge sheet/mesh filter.
Anything to block openings or holes?| Clean any dust and objects out of
nozzles, pipes and air openings.
Is suction inlet of nozzle or pipe closed?| Uncover and open suction inlet of
nozzle and pipe.
CAUTION: Do not attempt to repair the cleaner by yourself.
OPTIONAL ACCESSORIES
CAUTION : These accessories or attachments are recommended for use with
your Makita tool specified in this manual. The use of any other accessories or
attachments might present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask
your local Makita Service Center.
- Extension wand (Straight pipe)
- Nozzle
- Nozzle for carpet
- Shelf brush
- Corner nozzle
- Round brush
- Flexible hose
- High performance filter
- HEPA filter
- Seat nozzle
- Crevice nozzle
- Tool bag
- Makita genuine battery and charger
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms
applicable to this product.
If annexed warranty sheet is not available, refer to the warranty details set
forth at below website for your respective country.
United States of America: www.makitatools.com
Canada: www.makita.ca
Other countries: www.makita.com
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Makita Corporation
3-11-8, Sumiyoshi-chow,
Anjou, Aichi 446-8502 Japan
www.makita.com
885966A940 GLC03-1
EN, ESMX 20220228
Documents / Resources
|
makita GLC03 Cordless
Cleaner
[pdf] Instruction Manual
GLC03 Cordless Cleaner, GLC03, Cordless Cleaner, Cleaner
---|---
References
- Makita Canada | The Leader In Power tool Technology
- MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion
- Makita U.S.A | Cordless and Corded Power Tools, Power Equipment, Pneumatics, Accessories
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>