CASOLUX MERLE-FRONT-WHITE Courtesy Light Instruction Manual
- June 10, 2024
- CASOLUX
Table of Contents
- CASOLUX MERLE-FRONT-WHITE Courtesy Light
- Product Information
- Product Usage Instructions
- Product General Assembly
- Electrical diagram
- Assembly Instructions
- BEFORE YOU START
- Installation
- Cleaning Instructions and Care
- General Assembly
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CASOLUX MERLE-FRONT-WHITE Courtesy Light
Product Information
The product is a Merle LED courtesy light that comes in three colors – white, red, and blue. It has a power rating of 0.5 W and requires a voltage of 10-18VDC/10-30VDC. The light source of this fixture is not replaceable, and the whole unit needs to be replaced when it reaches its end of life. The product should be installed and disposed of according to the safety and environmental regulations.
Product Usage Instructions
Before using the product, read all safety instructions and ensure safe and proper use. If you find any damage to the electrical parts, consult a qualified electrician to complete the installation. Follow the current IET wiring regulations during installation. Keep the instructions for future reference.
Product General Assembly
For 24V:
- Drill two holes for the screws and one bigger hole for routing the cables through.
- Route the cables from the light through the hole. Connect the cable from the converter and the cable from the lamp using a 3m waterproof connector (see instructions a-b-c below).
- Connect the converter according to the electrical diagram.
- Screw in the light.
For 12V:
- Drill two holes for the screws and one bigger hole for routing the cables through.
- Route the cables from the light through the hole. Then connect the light according to the electrical diagram.
- Screw in the light.
Note: Take care when handling and installing to avoid damage to the product. Avoid mounting the fitting on a damp surface such as a newly painted or plastered area as this could cause discoloration of the finish. Disconnect the light before cleaning and do not use any chemical or abrasive solutions.
Electrical diagram
Assembly Instructions
| ITEM | POWER | VOLT |
|---|---|---|
| MERLE-FRONT-WHITE | 0,5 W | 10-18VDC/10-30VDC |
| MERLE-FRONT-RED | 0,5 W | 10-18VDC/10-30VDC |
| MERLE-FRONT-BLUE | 0,5 W | 10-18VDC/10-30VDC |
| MERLE-DOWN-WHITE | 0,5 W | 10-18VDC/10-30VDC |
| MERLE-DOWN-RED | 0,5 W | 10-18VDC/10-30VDC |
| MERLE-DOWN-BLUE | 0,5 W | 10-18VDC/10-30VDC |
BEFORE YOU START
Safety information
- Read all safety information before using the device to unsure safe and proper use.
- The light source of this light fixture is not replaceable, when the light source reaches its end of life the whole unit shall be replaced.
- It is extremely important that these instructions are read carefully, and any illustrations studied before commencing installation.
- Please keep these instructions for future reference.
WARNING!
- Electricity can be dangerous.
- Do not attempt to fit installation unless you are competent.
- If in any doubt consult a qualified electrician to complete electrical installation.
- Installation to comply with current IET wiring regulations.
- If you find any damage to the electrical parts, please ask a qualified electrician
- Be aware of electrical voltage on the different models to avoid damage
Correct disposal
This marking indicates that this item should be disposed of separately from
household waste. The item should be handed in for recycling in accordance with
local environmental regulations for waste disposal.
Installation
- Take care when handling and installing to avoid damage to the product.
- Avoid mounting the fitting on a damp surface such as newly painted or plastered area as this could cause discoloration of the finish.
Cleaning Instructions and Care
- Please disconnect the light before cleaning.
- Take extra care when cleaning and assembling.
- Do not use any chemical or abrasive solutions.
General Assembly
For 24V: (add dc/dc 10-30v driver)
- Drill 2 holes for the screws and 1 bigger for routing the cables through.
- Route the cables from the light through the hole. Connect cable from converter and cable from lamp using a 3m waterproof connector (see instructions a-b-c below) Then connect converter according to the electrical diagram.
- Screw in the light.
For 12V: (mount only light)
-
Drill 2 holes for the screws and 1 bigger for routing the cables through.
-
Route the cables from the light through the hole.
Then connect the light according to the electrical diagram -
Screw in the light.
Casolux Aps Borrevej 18, 6400 Sønderborg Phone: +45 74 45 00 05
www.casolux.com