Fenix HP30R V2.0 Headlamp User Manual
- June 10, 2024
- FENIX
Table of Contents
Fenix HP30R V2.0 Headlamp
Technical Parameters
The Fenix HP30R V2.0 Headlamp has the following technical parameters:
- ANSI/PLATO FL1
- Spotlight Mode: Turbo, High, Med, Low
- Floodlight Mode: High, Med, Low
- Spot & Flood Mode: Turbo High, Med, Low
- Output Runtime Distance Intensity:
- Turbo: 2000 lumens, 6 hours runtime, 251 meters distance, 15733-candela intensity
- High Spotlight Mode: 800 lumens, 12 hours runtime, 156 meters distance, 6104-candela intensity
- Med Spotlight Mode: 200 lumens, 34 hours runtime, 78 meters distance, 1515 candela intensity
- Low Spotlight Mode: 50 lumens, 120 hours runtime, 42 meters distance, 450-candela intensity
- High Floodlight Mode: 1000 lumens, 10 hours runtime, 78 meters distance, 291-candela intensity
- Med Floodlight Mode: 200 lumens, 34 hours runtime, 34 meters distance, 76-candela intensity
- Low Floodlight Mode: 50 lumens, 120 hours runtime, 17 meters distance, 17933-candela intensity*
- Turbo High Spot&Flood Mode: 3000 lumens, 5 hours runtime, 270 meters distance, 1812 candela intensity
- Med Spot&Flood Mode: 600 lumens, 17 hours runtime, 85 meters distance, 512-candela intensity
- Low Spot&Flood Mode: 150 lumens, 60 hours runtime, 45 meters distance, 291-candela intensity
- Impact Resistance
- IP66 is Water Resistant with a protection mechanism in the design
Operating Instructions
To use the Fenix HP30R V2.0 Headlamp:
- To turn on/off the lamp:
- With the lamp switched off, rotate the switch clockwise to enter spotlight mode.
- With the lamp switched off, rotate the switch counterclockwise to enter floodlight mode.
- With the lamp switched on, rotate the switch to the off state to turn off the lamp.
- To switch between modes:
- Spotlight mode: On floodlight mode, rotate the switch clockwise to the off state, and continuously rotate to enter spotlight mode.
- Floodlight mode: On spotlight mode, rotate the switch counterclockwise to the off state, and continuously rotate it to enter floodlight mode.
- Spot&Flood Mode: On spotlight or floodlight mode, single-click the side switch to enter spot&flood mode, and click again to exit.
- To select output:
- Spotlight mode: Rotate the switch to cycle through Low, Med, High, and Turbo.
- Floodlight mode: Rotate the switch to cycle through Low, Med, and High.
- Spot&Flood mode:
- On spotlight mode, rotate the switch to cycle through Low, Med, High, and Turbo.
- On floodlight mode, rotate the switch counterclockwise to cycle through Low, Med, and High.
- Note: The lamp does not have an intelligent memory circuit, each time it is turned on, the Low of the spotlight or Low of the floodlight will be activated.
Battery Specifications
The Fenix HP30R V2.0 Headlamp is compatible with the following batteries:
- ARB-L21 Series: 21700, 3.6V, recommended
- ARB-L18 Series: 18650, 3.6V, usable (with ALF-18*)
- Non-rechargeable CR123A: 3V, banned
- Rechargeable 16340: 3.6V, banned
- Rechargeable 18650: 3.6V, banned
Do not mix batteries of different brands, sizes, capacities, or types. Doing
so may cause damage to the headlamp or the batteries being used. Fenix ARB-L18
Series rechargeable Li-ion battery can also be used together with the ALF-18
battery holder. 21700 Li-ion batteries are powerful cells designed for
commercial applications and must be treated with caution and handled with
care. Only using quality batteries with circuit protection will reduce the
potential for combustion or explosion, but cell damage or short-circuiting are
potential risks the user assumes.
Battery Replacement
To replace the battery, open the cap to insert the battery in accordance
with the polarity marks, then replace the cap and fasten the latch.
Charging
To charge the Fenix HP30R V2.0 Headlamp, open the cap and plug the USB
Type-C side of the charging cable into the charging port of the battery case.
Technical Parameters
Note: According to the ANSI/PLATO FL1 standard, the above specifications are from the results produced by Fenix through its laboratory testing using two Fenix ARB-L21-5000 Li-ion batteries under the temperature of 21±3°C and humidity of 50% – 80%. The true performance of this product may vary according to different working environments and the battery used. The Turbo output is measured in a total of runtime including output at reduced levels due to temperature or protection mechanism in the design.
- 3000 lumens maximum output; 120 hours maximum runtime.
- One XHP50 white light LED, two XP-G3 S4 neutral white light LEDs; with a lifespan of 50000 hours.
- Included 2 x 5000mAh Li-ion batteries.
- Integrated die-casting ensures security and better heat dissipation.
- The rotary switch simultaneously activates spot- and floodlight modes.
- Dual interface for charging and discharging capability.
- Dual wearing way of battery case: can be clipped on the headband or can be belt-worn.
- Made of durable A6061-T6 aluminum.
- Premium type HAIII hard-anodized anti-abrasive finish.
- Headlamp: 3.62” x 2.20” x 1.73” / 92 x 56 x 44 mm.
- Battery case: 4.21” x 1.97” x 1.61” / 107 x 50 x 41 mm.
- Weight: 15.41 oz / 437 g (including battery and headband).
Operating Instructions
On/off
With the lamp switched off, rotate the switch clockwise, and the lamp enters
spotlight mode;
With the lamp switched off, rotate the switch counterclockwise, and the lamp
enters floodlight mode;
With the lamp switched on, rotate the switch to the off state to turn off the
lamp.
Mode Switching
- Spotlight mode: on floodlight mode, rotate the switch clockwise to the off state, and continuously rotate to enter spotlight mode.
- Floodlight mode: on spotlight mode, rotate the switch counterclockwise to the off state, and continuously rotate it to enter floodlight mode.
- Spot &flood Mode: on the spotlight or floodlight mode, single-click the side switch to enter spot&flood mode, and click again to exit.
Output Selection
Spotlight mode: rotate the switch to cycle through Low ⇄Med ⇄High ⇄Turbo.
Floodlight mode: rotate the switch to cycle through Low ⇄Med ⇄High.
Spot &Flood mode:
- On spotlight mode, rotate the switch to cycle through Low ⇄Med ⇄High ⇄Turbo.
- On floodlight mode, rotate the switch counterclockwise to cycle through Low ⇄Med ⇄High.
- Note: The lamp does not have an intelligent memory circuit, each time it is turned on, Low of the spotlight or Low of the floodlight will be activated.
Battery Specifications
Type| Dimension| Nominal
Voltage
| Usability|
---|---|---|---|---
ARB-L21 Series| 21700| 3.6V| Recommended| √√
ARB-L18 Series| 18650| 3.6V| Usable (with ALF-18 *)| √
Non-rechargeable
Battery (Lithium)
| CR123A| 3V| Banned| ×
Rechargeable
Battery (Li-ion)
| 16340| 3.6V| Banned| ×
Rechargeable
Battery (Li-ion)
| 18650| 3.6V| Banned| ×
- Do not mix batteries of different brands, sizes, capacities or types. Doing so may cause damage to the headlamp or the batteries being used.
- Fenix ARB-L18 Series rechargeable Li-ion battery can also be used together with the ALF-18 battery holder.
- 21700 Li-ion batteries are powerful cells designed for commercial applications and must be treated with caution and handled with care. Only using quality batteries with circuit protection will reduce the potential for combustion or explosion, but cell damage or short-circuiting are potential risks the user assumes.
Battery Replacement
Open the cap to insert the battery in accordance with the polarity marks, then replace the cap and fasten the latch.
Charging
- Open the cap and plug the USB Type-C side of the charging cable into the charging port of the battery case.
- In charging process, one indicator flashes: below 20%, one constant-on and one flashes: 20%
- 50%, two constant-on and one flashes: 50% – 80%, three constant-on and one flashes: 80%
- 95%, four constant-on: charging complete.
- When charging is complete, replace the anti-dust cap to ensure the waterproof and dustproof ability.
Note: 1. The normal charging time of the Fenix ARB-L21-5000 battery is about 4.5 hours from depletion to full charging, with the lamp being switched off. When charging, on/off and output selection can be used. 2. Recharge a stored headlamp every four months to maintain optimal Li-ion battery performance.
Power Bank Function
- witch off the lamp, plug the USB A socket of the charging cable into the battery case, and then connect another socket of the charging cable to the digital device.
- Single click switch next to the indicators to begin discharging (discharging current is 2A).
- In discharging process, four indicators flash: over 80%, three flash: 50% – 80%, two flash: 20% – 50%, one flashes: below 20%.
- When discharging complete, the indicators delay 30 seconds to go out to remind charging is complete. Be sure to close the anti-dust cover once charging is completed.
Battery Level Indication
With the lamp switched off, singly click the switch to check the battery
status, the indicators will
- last for 3 seconds.
- Four constant on: 100% – 80%
- Three constant on: 80% – 60%
- Two constant on: 60% – 40%
- One constant on: 40% – 20%
- One flashes: critical 20% – 1%
- Note: This only works with Fenix ARB-L21-5000 battery.
Intelligent Overheat Protection
The lamp will accumulate a lot of heat when used at relatively high modes for
extended periods. When the lamp reaches a temperature of 60°C or above, the
lamp will automatically step down a few lumens to reduce the temperature. When
the temperature drops below 60°C, it will then allow the user to reselect the
modes.
Low-voltage Warning
When the voltage level drops below the preset level, the headlamp is
programmed to downshift to a lower brightness level until Low mode is reached.
When this happens in Low mode, the lamp blinks 3 times every 5 minutes to
remind you to timely recharge or replace the battery. Note: This only works
with Fenix ARB-L21-5000 battery.
Headband Assembly
- The headband is factory assembled by default.
- Adjust the headband by sliding the buckle to the required length.
- If the headband is stained with sweat and mud, it can be washed directly.
Wearing Ways
- On the head: clip the battery case on the holder, and it can be assembled on the helmet with the included helmet attachment hooks.
- Belt-worn: clip the battery case on the included stainless steel belt clip, the lamp can be belt worn together with the extension cable.
Usage and Maintenance
-
Disassembling the sealed head can cause damage to the lamp and will void the warranty.
-
Fenix recommends using an excellent-quality Fenix battery.
-
If the lamp will not be used for an extended period, remove the battery, or the lamp could be damaged by electrolyte leakage.
-
Take out the battery to prevent accidental activation during storage or transportation.
-
Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring with an approved spare.
-
Periodic cleaning of the battery contacts improves the lamp’s performance as dirty contacts may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following reasons:
-
The battery needs replacing or recharging.
Solution: Replace or recharge the battery (Ensure the battery is inserted according to the manufacturer’s specifications). -
The contact point or contact of the battery or headlamp is dirty.
Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol. If the above methods don’t work, please contact the distributor.
-
Included
Fenix HP30R V2.0 Headlamp, 2 x Fenix ARB-L21-5000 Li-ion battery, USB Type-C
charging cable, 4 x Helmet attachment hooks, 3 x Cable clips, Stainless belt
clip, Extension cable, Spare O-ring, User manual, Warranty card
- The headlamp is a high-intensity lighting device capable of causing eye damage to the user or others. Avoid shining the lamp directly into anyone’s eyes.
- This headlamp will accumulate a lot of heat when used for extended periods, resulting in a high temperature of the headlamp shell. Pay attention to safe use to avoid scalding.
- Do not shine an object at close range, avoid burning the object or causing danger due to high temperature.
- The LED of this headlamp is not replaceable; so the entire lamp should be replaced when the LED reaches the end of its life.
- If any of the information provided in this manual is changed, the new version of the manual shall prevail; if your included user manual is an old one, it acquiesces that we won’t send a new manual.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>