Avalue Technology SID-10W04 Rosch Computer User Guide

June 10, 2024
avalue Technology

Avalue Technology SID-10W04 Rosch Computer

Copyright Notice
Copyright 2022 Avalue Technology Inc., ALL RIGHTS RESERVED.

FCC Statement

Federal Communication Commission Interference Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Notice:

  1. An Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord by used.
  2. Use only shielded cables to connect I/O devices to this equipment.
  3. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. When nearby persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than 20 cm.

WARNING

  • “CAUTION – Use suitable mounting apparatus to avoid risk of injury.”
  • “CAUTION – Use a power cord that matches the voltage of the power outlet, which has been approved and complies with the safety standard of your particular country.”
  • “WARNING – To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth.”

Notice
This guide is designed for experienced users to setup the system within the shortest time. For detailed information, please always refer to the electronic user’s manual.

Copyright Notice

Copyright 2022 Avalue Technology Inc., ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.

Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.

Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Avalue Technology assumes no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement unless otherwise specified. Applications that are described in this manual are for illustration purposes only. Avalue Technology Inc. makes no representation or warranty that such an application will be suitable for the specified use without further testing or modification.

Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL OF Avalue Technology Inc.

As used herein:

  1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into body, or (b) support or sustain life and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.
  2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

A Message to the Customer

Avalue Customer Services
Each and every Avalue product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Avalue device is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Avalue has come to be known. Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To ensure you get the full benefit of our services, please follow the instructions below carefully.

Technical Support
We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones we can give over the phone. So please consult the user’s manual first. To receive the latest version of the user’s manual; please visit our Web site at: http://www.avalue.com.tw/ 4 SID-10W04 Quick Reference Guide

Getting Started

Safety Precautions

Warning!
Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis.

Caution!
Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges. As a safety precaution, use a grounding wrist strap at all times. Place all electronic components in a static-dissipative surface or static-shielded bag when they are not in the chassis.

Packing List

  • 1 x SID-10W04 Panel PC
  • 1 x AC 60W Adapter
  • 1 x Power cord
  • 2 x WiFi Antenna
  • 4 x Screw-Flat M4* 4mm

If any of the above items is damaged or missing, contact your retailer.

System Specifications

Component

Mother Board| ACP-APL
CPU| Intel Celeron J3455 1.5GHz
CPU Cooler (Type)| Heatsink
Memory| 4GB DDR3L SO-DIMM 1866
Power Supply| DC in
Adapter| 60W / 12V
Speaker| 4ohm / 2W (Optional)
Wireless LAN| 1 x 802.11 a/b/g/n/ac Wireless LAN
Bluetooth| BT 5.0
Operating System| 2019 Win 10 / Ubuntu 20.04 (TBD) / Android 8.1 (TBD)
Storage
Solid State Drive| 32GB eMMC (Samsung 32GB S IC FL 32G KLMBG2JETD-B041 FBGA 153P)
Panel
LCD Panel| 10.1” KD101N42-40NA-A042
Touch Screen| 10.1” Sense ST-101C34B
Touch Controller| ILI 2511
Resolution| 800 x 1280
Luminance| 350 cd/m² (typ.)
External I/O
DC in Power jack| JDCIN1: Power Jack_90D

Pwr-in 12V~24V

HDMI Port| JHDMI1: HDMI Port_90D
USB Port| JUSB1: USB Type A Host (3.0)_90D

JUSB2: USB Type A Host (3.0)_90D

Lan Port| JLAN1: 10/100/1000 Lan port_90D
Audio Port| JHP1: Headphone Jack_90D
Serial Port| 1x DB9 for RS-232(Default)
Switch| 1x Power button w/ LED

1x Power sw button_90D

Wireless Antenna| 2x Dipole Antenna
LTE Antenna| 2x Dipole Antenna (Optional)
Mechanical
Power Type| 12V~24V wide voltage DC input
Power Connector

Type

| ****

DC jack

SID-10W04

Dimension 258.8×182.8×49.6 mm
Weight 2.6 kg
Color Metallic
Fanless Yes
OS Support 2019 Win 10 / Ubuntu 20.04 (TBD) / Android 8.1 (TBD)

Reliability
EMI Test| CE/FCC Part 15, Subpart B
Safety| IEC-62368-1 & EN62368-1
Dust and Rain Test| Front Panel IP65

Random Vibration Test

| Test Standard: Reference IEC60068-2-64 Testing procedures

1. System condition: Operation mode 2. PSD: 0.00454G²/Hz , 1.5 Grms

3.       Test Frequency : 5-500Hz

4.       Test Axis : X,Y and Z axis

5.       Test time: 30 minutes per each axis Storage : eMMC

Sine Vibration Test (Non-operation)

| Test Standard: Reference IEC60068-2-6 Testing procedures

1.       System condition : Non-Operating mode

2.       Test Acceleration : 2G

3.       Test frequency : 5~500 Hz

4.       Sweep:1 Oct/ per one minute. (logarithmic)

5.       Test Axis : X,Y and Z axis Test time :30 min. each axis

Packing Vibration Test

| 1. PSD: 0.026G²/Hz , 2.16 Grms

2.  Non-operation mode

3.  Test Frequency : 5-500Hz

4.  Test Axis : X,Y and Z axis

5.  30 min. per each axis

6. IEC 60068-2-64 Test:Fh

Mechanical Shock Test

| Test Standard: Reference IEC60068-2-29 Testing procedures

1.       System Condition: Operation

2.       Wave form: Half-Sine wave

3.       Acceleration: Rate: 10g

4.       Duration: Time: 11ms

5.       No. of Shock: Z axis 300 times

6.       Test Axis: Z axis

Drop Test

| Reference ISTA 2A, Method: IEC-60068-2-32 Test:Ed

1.       Test Phase: One comer, three edges, six faces

2.       Packing weight: around 1.5kg

Test high: 96.5cm (Based on product weight)

Operating

Temperature

| ****

0°C ~ 40°C (32°F ~ 104°F)

---|---
Operating

Humidity

| ****

40°C @ 95% Relative Humidity, Non-condensing

Storage

Temperature

| ****

-20°C ~ 60°C (-4°F ~ 140°F)

Note: Specifications are subject to change without notice.

System Overview

Side ViewAvalue-Technology-SID-10W04-Rosch-Computer-
FIG-1

Connectors| |
---|---|---
Label| Function| Note
Line out| Audio line-out connector| Head phone jack
HDMI| HDMI connector| HDMI type A
USB3.0| 2 x USB3.0 connector|
Power| Power on button|
DCIN| DC power-in connector| DC jack
LAN| RJ-45 Ethernet connector|
COM| Serial port connector| DB9 for RS-232 connector

System Dimensions

Hardware Configuration

Note: If you need more information, please visit our website: http://www.avalue.com.tw

SID-10W04 connector mapping

Serial port connector (COM)Avalue-Technology-SID-10W04-Rosch-Computer-
FIG-3

RJ-45 Ethernet connector (LAN)

Avalue-Technology-SID-10W04-Rosch-Computer-FIG-4

HDMI connector (HDMI)Avalue-Technology-SID-10W04-Rosch-Computer-
FIG-5

USB3.0 connector (USB3.0)Avalue-Technology-SID-10W04-Rosch-Computer-
FIG-6

SID-10W04 Quick Reference Guide

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals