Mannsberger 24V Mini Electric Chainsaw Wood Cutting Lithium Instruction Manual
- June 10, 2024
- Mannsberger
Table of Contents
Instruction manual
Before using this appliance, read the safety instructions carefully.
PRODUCT DESCRIPTION
- Guide plate
- Side cover
- Cord eye
- Felling dog
- Nut
- Power switch
- Battery
- Wrench Loosen the nut counterclockwise and remove the side cover.
HOW TO USE
IMPORTANT: Always make sure the battery is disconnected from the chainsaw.
- How to install the chain
First load the chain into the guide plate, and the middle guide tooth just sticks into the guide plate guide slot.
Note: the chain blade should be forward.
Note: The chainsaw has a device to adjust the tension of the chain. When installing the guide plate, make sure the adjusting block gets stuck into the positioning adjusting hole at the end of the guide plate! Put the chain into the guide plate.
Pay attention to the
direction of the cutting teeth.
Install the chain around the gear and align the
saw blade with the pin hole.
Install the side cover and tighten the screw nut.- How to adjust the chain tightness The standard is to lift the chain in the middle of the guide plate and expose 1-3 middle guide teeth Loosen the compression nut.
As shown in the picture, twisted the adjusting screw clockwise to tension the chain, counterclockwise is for looseness.
- The chain tightness is shown as below.
Note: 1-3 middle guide teeth are exposed in the pull-down chain. The new chain will be stretched in the early stage of use. Please check and adjust to the appropriate tension frequently, because the loose chain is easy to derail, which may lead to rapid wear of the chain and guide plate. The chain must be stuck to the sprocket. After installation, please check it again.
and the guide
directly.
- How to adjust the chain tightness The standard is to lift the chain in the middle of the guide plate and expose 1-3 middle guide teeth Loosen the compression nut.
HOW TO CHARGE
- Do not expose the battery to extreme conditions such as high temperature or shock, or it will cause personal injury due to the leakage of the electrolytic solution.
- Before charging, check that the surface of the battery is clean and dry.
- The battery of this product is not fully charged before the delivery. So it must be fully charged before first use.
- Do not charge the battery for long periods all the time, and try to avoid using up the battery, otherwise it will damage the battery.
- We do not guarantee the chain saw malfunction due to incorrect use.
- If the battery charging time becomes obviously shorter than before, which shows that the battery has been exhausted and should be replaced soon.
- The user can only use the battery pack made by the original manufacturer.
- Always keep in mind applicable safety instructions, environmental regulations and environmental information
- Put the charger indoor in the temperatures of 10 °C-22°C.
- Please kindly check whether the switch is off or not.
- Connect the charger to the connector of battery pack.
- Make sure the power is consistent with the rated values on the charger.
- Red light on the charger indicates the battery is charging, green light means fully charged, and the average charging time is 2 hours.
- Please pull the connector off the electricity, and stop the connection of the connector and battery after fully charged.
- ln order to prolong the lifespan of the battery, please make sure to charge the battery at least every three months on the condition it is not used for a long time.
- Working Conditions: Charging temperature: 0°C- 45°C for charger and battery pack, discharging temperature: -10°C- 60°C.
- Make sure the battery is disconnected from the chainsaw, when you do maintenance.
OPERATING INSTRUCTION
- Please wear suitable clothing and working gloves when using the device. Make sure the chain saw works fine before use. Start/off switches and safety switch must be available for normal use.
- When loosening the start switch, the power must be turned off. If the switch is damaged, stop using the device. Make sure the voltage of the power supply is consistent with the voltage on the nameplate. The risk of injury can be reduced by wearing protective devices and ensuring that the devices are functioning properly.
- Confirm the operation frequency to ensure it works best. Once stop cutting, turn off the power and remove the battery pack.
- In order to prolong the lifespan of battery pack and ensure the best service life of pruning and shearing, do not allow to cut wet and dry branches over 100mm diameter.
CUTTING SKILLS
-
When the chain saw is running, keep your other hand at least 15cm away from the cutting, and your hands must not be put near the blade.
-
Do not use the chain saw to cut the bigger branches forcibly, otherwise the chains will be stuck.
-
To protect the battery pack, put it under waterproof environment on cold or humid days.
Do not use the chain saw on rainy days. -
It is strongly suggested the battery pack be taken out of the device after use. It is also advised to disconnect the connection of the chain saw and the battery pack, keep the power switch off and put into the tool box together.
-
If the user feels the power is not enough or the cutting is not smooth, please kindly check if the power is exhausted or the blade is dull.
CLEANING AND MAINTENANCE
- To ensure safety use, only the original parts can be used.
- Repair work functions not mentioned in this specification are performed by the service center. To ensure safe use, only original parts can be used.
- Please tum off the equipment before maintenance. Disconnect the battery from the device and store the battery pack in a secure package.
- Please wear gloves when touching the chain, which prevents the sharp blade from cutting the user. Follow-up cleaning and maintenance must be carried out regularly. This will ensure the long-term reliable operation of the device.
- Clean the chain carefully after each use. Wipe the chain with lube oil and spray with metal protective spray. Use oily cloth to wipe the blade and absorb the metal to protect the rust.
- Do not spray the equipment with water or soak into the water, otherwise, it may cause electric shock. Use a damp cloth or brush to clean.
- After 8-hour continuous operation, please remove the debris such as dust from the front turbulent cover plate of the equipment.(Please refer to the installation picture for disassembly and maintenance steps.)
STORAGE
To ensure that the battery is fully charged, avoid exposing the device to
extreme heat or cold. If the device will not be used for a long time, please
remove the battery before storage.
The battery and charger must be placed in the storage box to prevent heat,
dust and moisture from entering.
-
Please kindly check whether the switch is shut off or not.
-
The battery should be stored in a dry environment under:
Short term (less than 1 month) storage temperature: -20°C and +60°C
Short term (less than 6 months) storage temperature: -10°C and +35°C
Recommended long term storage temperature: 0°C and +30°C -
The distance between the battery and the combustible must be kept beyond 150cm.
-
To prolong the lifespan and prevent its degradation, store it in a fully charged state.
When not in use, charge and discharge the battery at least every two months. -
Do not turn on the power switch while charging. When the indicator light on the charger is red, which means it is charging; when the light becomes green, it means it is fully charged.
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>