4DRC 4D-F12 Quadcopter GPS Brushless Drone with 4K Camera Instruction Manual
- June 10, 2024
- 4DRC
Table of Contents
- 4D-F12 Quadcopter GPS Brushless Drone with 4K Camera
- List of accessories included:
- Name of each part of aircraft:
- Wind blade installation diagram:
- Unfolding steps of the aircraft: (It is in the storage state when it
- Lithium battery charging instructions:
- Name of each part of the remote control:
- Battery charging instructions of the remote control:
- APP download and installation instructions:
- APP control interface function introduction:
- Environmental requirements before flight:
- Preparation instructions before flight
- Control method:
- Introduction to the APP application and remote control function
- FAQ and solving guidelines:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
4D-F12 Quadcopter GPS Brushless Drone with 4K Camera
Instruction Manual
4D-F12 Quadcopter GPS Brushless Drone with 4K Camera
In order to meet the requirements of the aeronautical radio station’s
electromagnetic environment (various of aero models and UAV are not allowed to
fly within the range of 10 km on each side of center line and 20km on both
ends of the airport runway and in the) and civil aviation routes and airlines.
Using various models and drones in the no-fly zone issued by the relevant
state departments is prohibited.
Warning
- The packaging and instructions contain important information and should be kept.
- With this aircraft, you are responsible for ensuring that no harm will be caused to the personal and property of others.
- Commissioning and installing of aircraft must be strictly in accordance with the operating instructions, and attention shall be paid to the distance between the aircraft and the user or other people shall be 2 to 3m to prevent the aircraft from bumping into the head face and body of people and causing injury in flying and landing, etc.
- Our company and distributors are not responsible for any loss and damage, as well as injury to people caused by improper use or operation.
- Children should be guided by adults when operating the aircraft. This product is prohibited to be operated by children under 14 years old.
- Please follow the instructions or packaging instructions to install and use correctly, and some parts should be assembled by adults.
- The product contains small parts, please place it out of the reach of children to prevent the risk of accidental eating or suffocation.
- It is strictly forbidden to play on the road or in the place where water is accumulated to avoid accidents.
- Please put away the packing materials in time to avoid harm to children.
- Do not disassemble or modify the aircraft. Disassembly or modification may cause malfunction to the aircraft.
- The charging cable needs to be inserted into the designated power supply 5V =2A that is the same as the product label.
- The use of other charging cables will cause damage to the battery and may cause unexpected dangers.
- The charging cable is not a toy.
- When charging the rechargeable battery, it must be under the supervision of an adult. When charging, it must be far away from flammable materials. During charging, the guardian should not leave the monitoring range.
- Please do not shod circuit or squeeze the battery to avoid explosion.
- Do not mix different types of lithium batteries.
- The aircraft uses a rechargeable lithium battery, which needs to be pulled out for charging.
- Do not shod-circuit, decompose or throw the battery into fire; do not put the battery in a place with high temperature and heat (such as in fire or near electric heating device).
- The aircraft should be used as far away from other electrical equipment and magnetic objects as possible, they may cause mutual interference.
- Please keep a safe distance from the high-speed rotating propeller to avoid the risk of scalp or cut
- The motor is a hot part; please do not touch it to avoid bums.
- LED has laser radiation; please do not give direct light beam to others.
- Do not use the model near your ears! Misuse may cause hearing damage.
- The USB charging cable must use the data cable provided by our company to charge the battery, otherwise it will cause serious damage to the battery and will lead to unexpected danger.
- To meet the magnetic environment requirements of aeronautical radio stations. During the radio control order issued by the relevant state departments, the model remote control should be stopped within the city area as required.
- Turn off the switch and unplug the battery when the battery of the aircraft is used up, and charge after 30 minutes of rest, otherwise the battery will be easily damaged.
List of accessories included:
Name of each part of aircraft:
Wind blade installation diagram:
Unscrew the screw and remove the
fan blade.
Note: The fan blade is printed with letters of Al. A2, Bl, and B2, in
which, Al = A2, B1 = B2, please install it correctly according to the diagram,
otherwise it cannot take off.
Unfolding steps of the aircraft: (It is in the storage state when it
leaves the factory)
1. Unfold the aircraft according to the steps
Lithium battery charging instructions:
5.1 Buckle the battery lock of the aircraft.
5.2 Remove the battery.
5.3 Charging:
Insert the USB port of the USB charging cable into the computer USB port (or
use 5V —2A power adapter), and connect the other end of the USB charging cable
to the battery socket. When charging, the red indicator on the module battery
is on, and when the battery is fully charged, the red indicator light goes
out, which means that the charging is complete.
It must be charged with the aircraft charging cable provided by the factory,
and other charging cables cannot be used. Be sure to remember to avoid
accidents.
Warning: When not flying, please do not install the battery in the
aircraft to avoid battery damage.
Name of each part of the remote control:
LCD display instructions:
Normal/GPS button: Press and hold
this button for 3 seconds after frequency matching to switch between normal
mode and GPS mode (it is by default in GPS mode after starting, and GPS icon
is on, and GPS icon is off in normal mode).
Switch between left-hand and right hand throttle: it is by default in left-
hand throttle, press and hold the camera downward fine-tuning button, then
press the power button to switch to right-hand throttle
Battery charging instructions of the remote control:
Charging: Insert the USB
port of the USB charging cable into the USB port of the computer, and connect
the port of the other end of the USB charging cable to the battery socket.
When charging, the power indicator of the remote control is green, and the
power indicator turns off when it is fully charged.
Warning Remember that the remote control charging cable cannot be used
interchangeably with the aircraft charging cable.
APP download and installation instructions:
8.1 Download and install the software
For Google mobile phone, after scanning the code, choose to open and download
in the browser
https://apps.apple.com/cn/app/id1510269271
8.2 Link description
- Turn on the power of aircraft, enter the (Settings) option (of mobile phone or IPAD), and open the wireless network; find the device name of “4DRC ” in the wireless network search list and connect; after connection, exit the setting option.
- Open the software icon “of 4DRC PRO” in mobile phone to enter the control interface. (Try to stay away from other signal source environments when flying)
APP control interface function introduction:
Note: The lens can be
switched in Indoor mode, and in GPS mode, the lens switch function will be
turned off.
Note: After being
proficient In flight operation, It is necessary to close the novice mode and
set the fright distance and altitude before the aircraft can fly further!
Environmental requirements before flight:
Please choose an outdoor and open environment with no rain and snow and low wind. Please stay away from crowds, trees, wires, tall buildings, airports, and signal transmission towers when flying. Do not fly in a too small indoor environment with lots of things.
Preparation instructions before flight
11.1 Aircraft frequency matching: Turn on the power of the aircraft and place
it on a horizontal surface. At this time, the aircraft placed on the
horizontal surface will automatically enter the frequency matching state, and
the front blue light and the rear red light will flash. Set the aircraft in a
correct direction, and the nose shall face forward. It must be placed on the
horizontal plane.
11.2 Turn on the WiFi function
in the mobile device, select “40RD—en*” in the WiFi list, and open the APP
after it connected successfully.
11.3: Turn on the remote
control (default mode): long press the power switch button ()(step 1), turn on
the power and the indicator flashes: push the throttle lever up to the top
(step 2) and then to the bottom (step 3), and thus the frequency matching is
successful, the UAV lights change from flashing to being permanently on.
warnbill It must ensure that the power of the aircraft/remote control is
sufficient or it cannot take off!
11.4 Horizontal calibration
operation:
Short press the horizontal calibration button on the remote control , the blue
and red lights on the aircraft will flash quickly. When the blue and red
lights on the aircraft are always on and the calibration is complete (Figure
1).
APP application operation: Click “Set more icon in the APP interface, and
follow the text prompt steps after entering, and it can also be horizontally
calibrated (Figure 2).
Note: In calibration, the aircraft must be placed on a horizontal surface
to complete the calibration.
11.5 Geomagnetic calibration operation
- Long press the geomagnetic calibration key 1,ZO. until the front blue light and the rear red light flash on the aircraft.
- Rotate horizontally clockwise to pick up the aircraft, rotate clockwise until the front blue light is always on and the rear red light flashes, and the remote control emits a beep, it means that the horizontal calbration is completed.
- Rotate clockwise with the tail of the aircraft is upward -pick up the aircraft, with its nose being vertically down. and rotate clockwise until the blue light on the front and the red light on the rear of the aircraft are always on, and the remote control emits a beep, it means that the guide calibration is completed.
APP application operation: In entering the interface of ‘Setting more”,
according to the text prompt and operation steps, you can also guide the
calibration (Figure 4).
11.6 Star search status (In
GPS mode by default)
When the remote control is in GPS mode, GPS icon will be ON, which means that
the GPS enters the star search state. When the red tail light of the aircraft
flashes, it means that the star search is successful, and the remote control
will emit a prompt of “beep”. The aircraft can be unlocked at this time
(Figure 5).
Note: The first time of star search needs to wait at least a few minutes,
and the search signal reaches about 10 stars before it can take off.
11.7 StarUstop (GPS mode)
Push the left and right joysticks on the remote control outward to unlock, (If
the star search Is unsuccessful, it cannot be unlocked and started) (Figure
6). At this time, the aircraft can take off normally. After taking off, all
the indicators of the aircraft are always on. APP operation: Click “One Key
Unlock” icon (Figure 7) in APP control interface, the one-key unlock function
can also be achieved.
11.8 One-key take-off and
landing
APP operation: Click the “One-Key Takeoff’ icon (Figure 8) in APP control
interface. During the flight, click this icon again, and the aircraft will
automatically land slowly.
11.9 Start / stop (common mode
needs to be turned on for indoor operation) / Normal mode (GPS icon on the LCD
screen is OFF)
- Long press the GPS button on the remote control 8, the remote control (GPS on the LCD screen will switch to OFF) will enter the normal mode (Figure 9)
- Push the left and light joysticks on the remote control outward to unlock (Figure 10)
- Then push up the left joysticks (Figure 11)
Before flying, please perform the following steps in the above order: open (refer to 11.1) —• link to WIFI (refer to 11.2) —• remote control to start frequency matching(refer to 11.3) horizontal calibration (refer to 11.4) —• geomagnetic calibration (refer to 11.5) —• Star search status (in GPS mode by default) (reference 11.6) —• start/stop (GPS mode) (reference 11.7) —,One-key take-off and landing (refer to 11.8) —.Start / stop (common mode needs to be turned on for indoor operation) Normal mode (refer to 11.9)
Control method:
APP application operation: Enter the APP control interface and click the more
functions” icon to open the “joystick on/off” icon, you can see the operation
joystick on the interface. The operation method is as follows:
When the left joystick
(throttle) is pushed up, the rotation rate of the main blade increases and the
aircraft rises. When the left joystick (throttle) is pushed down, the rotation
rate of the main blade slows down and the aircraft descends.
When the left joystick
(rudder) is pushed to the left, the aircraft nose turns to the left. When the
left joystick (rudder) is pushed to the right and the nose of the aircraft
will turn to the right.
When the right joystick (rudder) is pushed up, the aircraft moves forward.
When the right joystick (rudder) is pushed down, the aircraft moves backward.
When the right joystick (rudder) is pushed to the right, the aircraft fuselage
deviates to the right. When the right joystick (rudder) is pushed to the left,
the aircraft fuselage deviates to the left.
When the aircraft is in lm
from the ground, the aircraft will become unstable due to the influence of its
own blade vortex, which is called “ground effect response”. The lower the
height of the aircraft, the greater the effect of the ground effect response.
Introduction to the APP application and remote control function
operation:
13.1 Headless mode
Auto The front of the aircraft when the code-matching is turned on is by
default the front in headless mode; if it is necessary to adjust the
direction, please turn on the code-matching again, and short press the remote
controller “headless mode function key (Figure 12). When exiting, please tap
gently press this function key again.
Special prompt: Please make sure the aircraft is aligned with the
straight line and let the gyroscope automatically detect the straight line,
and the headless mode of straight line flight can be realized.
13.2 One key return
Press the one-key return button , the aircraft will return to the place above
the geomagnetic calibration position (Figure 13). (The aircraft will
automatically rise to a safe altitude when it is flying below the safe
altitude) and then land slowly. If there are obstacles during the landing,
press the one-key return button again to turn off the return operation and
avoid by the manual control joystick, pull down the throttle lever to land.
APP operation: Click the -one-key return” icon (Figure 14) in the APP
control interface, you can also return the aircraft; during the return flight,
click this icon again to cancel the return.
Runaway return: When the
signal of the remote controller is interrupted for about 4s. the aircraft will
automatically return to the place where there is a signal and stop. Low
battery return: when the aircraft is in low battery electricity, it will
forcefully return to a place that is 20m above the take-off point. The return
flight cannot be cancelled during the low battery return.
13.3 Speed switching
When the aircraft takes off, it is in low-speed mode (3 shifting gears) by
default; lightly press the remote control, it will emit two sounds of “beep”,
it will enter “high-speed gear”. (Figure 15)
APP operation: Click the “More Functions” icon (Figure 16) in the APP control
interface, and the flight speed can also be switched (Figure 17).
13.4 Waypoint flight mode
(1) In GPS mode, click “More Functions” icon (Figure 18) in the APP control
interface to enter waypoint flight (Figure 19). At this time, the interface
changes from the image transmission page to the map page. On the map page,
click to set the track range of a single waypoint or continuous waypoints
(Figure 20). During the selling process, if the track waypoints are too dense,
you can click the delete icon to delete all waypoints (Figure 21)
2. After setting of the waypoint, click the send icon (Figure 22), the
aircraft will fly to all waypoints from the initial point to complete the
preset flight trajectory. The direction of the aircraft can be controlled by
the joystick during the flight.
13.5 Orbital flight mode
In GPS mode, click “More Features” icon in the APP control interface (Figure
23) to enter the orbit flight mode (Figure 24), the aircraft will
automatically orbit in a radius (Figure 25), and the radius can be adjusted on
the APP (Figure 26). At this time, push the right direction joystick to fly
left or right (Figure 27) at the default speed, the orbital speed can be
adjusted. Push the right direction joystick front or rear, the orbit radius
can be adjusted, and when the orbit button is pressed again, the orbit flight
will end (Figure 28).
13.6 GPS follow mode
In GPS mode, click the “More Functions” icon (Figure 29) in the APP control
interface to enter the follow (Figure 30). The aircraft will use the distance
from the current position to the operator (mobile phone or IPAD) device as a
reference, and move by tracking changes in the location of mobile devices. In
following, lightly press the red icon to cancel the following.
13.7 Lens adjustment
Press the fine adjustment button for the camera angle on the remote control,
and the operator can adjust the lens angle as needed (Figure 31).
APP application operation: Click on the “More Functions” icon (Figure 32) in
the APP control interface to enter the lens adjustment (Figure 33), and the
operator can adjust the lens angle as needed (Figure 34).
13.8 Gesture Recognition
When facing the camera’s front lens, click the gesture photo button on the
APP, and use any of the following gestures to trigger the aircraft’s photo or
camera function.
**Special Tip: Please face the lens with the front being at a position
about 2-3M away and in a better light and background environment to perform
the gesture recognition. Yeah gesture photo
In about 3m front of the aircraft lens, make Yeah gesture with one hand in
horizontal position; after the aircraft successfully recognizes the gesture,
count down 3 seconds and take photos.
Palm gesture video-recording
In about 3m front of the aircraft lens, put five fingers together and lift one
hand to horizontal position; after the aircraft successfully recognizes the
gesture, it will start recording. The recording will end when the gesture is
re-recognized (the time difference between the two recognitions shall be
greater than 3s).
13.9 MV interface
Click the “filter interface” icon (Figure 35) in the APP control interface,
after entering the filter interface, you can choose to match your favorite
filter effect, click the recording icon to start recording (Figure 36). After
the recording is completed, the synthesized short video or picture will be
saved to the media library (Figure 37).
****Special Tip:** During the recording process, you can rotate the screen
or switch the filter effect, and you can also turn the joystick on / off to
control the direction and altitude of the aircraft.
FAQ and solving guidelines:
Question | Reason | Solution |
---|
The aircraft indicator flashes
without any response| 1.Geomagnetic anomaly
2.The aircraft has insufficient power| 1.Move the aircraft to an open area and
recalibrate the geomagnetism. For steps, please refer to the manual, 11.5
Geomagnetism Calibration.
2.Charge the battery
The blades of the aircraft rotate but cannot fly| 1. Low battery
2.1 Blade deformation
2.2 Installation error of AB propeller| 1. Charge the battery
2.1 Replace the blade
2.2 If B1/B2 blade is broken, replace B1/B2. If A1/A2 blade is broken, replace
A1/A2. If replace the wrong pads, the aircraft will not take off.
The aircraft vibrates badly| Blade deformation| Replace the blade
Fine tuning is done but still can’t make the aircraft stable| 1.Blade
deformation
2.Defective motor| 1.Replace the blade
2.Replace the motor
After the impact, start the aircraft again and it fly uncontrollably| The
three-axis acceleration sensor ld its s aance due tob timpact| It will be OK
after 5-10s of resting the aircraft, or by geomagnetism calibration and level
calibration.
For the steps, please refer to the manual, 11.4 horizontal calibration
operation.