Light Efficient Design LED-8056EXXD-A Low Bay Retrofit Lamp Installation Guide
- June 10, 2024
- Light Efficient Design
Table of Contents
Light Efficient Design LED-8056EXXD-A Low Bay Retrofit Lamp
PRIOR TO INSTALLATION, PLEASE READ THE ENTIRE INSTALLATION INSTRUCTIONS
- CAUTION – THESE RETROFIT LAMPS ARE DESIGNED TO OPERATE ONLINE VOLTAGE, BALLAST MUST BE BYPASSED.
- SUITABLE FOR USE IN DRY OR DAMP LOCATIONS.
- SUITABLE FOR USE IN ENCLOSED LUMINAIRES.
- NOT FOR EMERGENCY LIGHTING.
- NOT FOR USE IN ENVIRONMENTS WHERE EXPLOSIVE OR CORROSIVE GASES ARE PRESENT.
- DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.
WARNING – RISK OR FIRE OR ELECTRIC SHOCK. LED RETROFIT KIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRE ELECTRICAL SYSTEMS. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.
WARNING – RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY IN
LUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE
PHOTOGRAPHS AND/OR DRAWING AND WHERE THE THE INPUT RATING OF THE RETROFIT KIT
DOES NOT EXCEED THE INPUT RATING OF THE LUMINAIRE.
WARNING – TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO
EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.
FOR INSTALLATIONS IN CANADA – THIS RETROFIT IS ACCEPTED AS A COMPONENT OF A
LUMINAIRE WHERE THE SUITABILIY OF THE COMBINATION SHALL BE DETERMINED BY
AUTHORITIES HAVING JURISDICTION. LAMPS COME WITH A 5-YEAR WARRANTY AGAINST
MANUFACTURING DEFECTS. THIS WARRANTY DOES NOT COVER PHYSICAL DAMAGE OR
IMPROPER OPERATION.
INSTALLATION REQUIREMENTS
MODEL| INPUT VOLTAGE| LAMP HOLDER| MIN. LAMP COMPARTMENT
DIMENSIONS| LUMINAIRE| ORIENTATION
---|---|---|---|---|---
LED-8056EXXD-A| 120-277 VAC 50/60 Hz| ****
E26
| ****
7.5″ x 8.5″
| ****
Enclosed or Open
| ****
Base Up
LED-8056EXXCD-A| 220-347 VAC 50/60 Hz
LED-8056MXXD-A| 120-277 VAC 50/60 Hz| ****
E39 or EX39
| ****
7.5″ x 8.5″
| ****
Enclosed or Open
| ****
Base Up
LED-8056MXXCD-A| 220-347 VAC 50/60 Hz
INSTALLATION INSTRUCTIONS
- Turn off power to the luminaire at the switch and circuit breaker. Allow the luminaire to cool before proceeding.
- Ensure that the luminaire and electrical inputs meet the requirements in the table. The lamp may be installed in an open or enclosed fixture indoors, or an enclosed fixture outdoors. Please ensure that the lamp is protected from direct water spray and bugs.
- If a ballast is present, it must be bypassed. If desired, it may be removed. Please refer to the wiring diagram. Disconnect or cut the wires to and from the ballast. Connect the line and neutral wires to the socket leads as shown in the wiring diagram. The product may be installed using two hot leads if a neutral is not available. Check that voltage meets the requirements.
- Inspect the lamp holder for arcing or corrosion and replace if damaged.
- If using dimming, see the second page for wiring instructions.
- Screw the lamp into the lamp holder. Do not over-torque as this could cause damage.
- Apply included label to the inside of the luminaire where it will be visible during relamping.
- Turn on the electrical power to the luminaire and verify proper operation.
CONTENTS
- Lamp
- Label
- Dimming connection plug
- Instructions
WIRING
LOW BAY RETROFIT LAMP
DIMMING CONNECTION
- Use wiring approved for unenclosed Class 2 circuits.
- Open the dimming port located on the top funnel of the lamp.
- Insert the supplied plug into the port.
- Carefully screw in a lamp into the luminaire while making sure not to tangle wires.
- Connect 0-10V wires to a listed 0-10V dimmer, sensor or controller using listed wire connectors.
- If using a sensor or controller that requires 12V power connect wires using listed wire connectors, otherwise make sure the wires remain capped.
- Organize and secure wires in the luminaire using listed cable ties or other wire management devices.
- The lamp will continuously dim down to 10% using a 0-10V signal.
LIGHT EFFICIENT DESIGN HEADQUARTERS 188 S. Northwest Highway • Cary, IL 60013 INNOVATION & MANUFACTURING CENTER 30 Log Bridge Road, Building 200 • Middleton, MA 01949 847.380.3540 • led-lIc.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>