Craftsman Garage Door Opener Keypad CMXZDCG440 User Manual
- June 10, 2024
- Craftsman
Table of Contents
Craftsman Garage Door Opener Keypad CMXZDCG440 User Manual
INSTALLATION
Compatible with garage door openers manufactured after January 1, 1993. Make sure the garage door opener has a working light bulb because it is a programming indicator.
Install the battery and program the keypad prior to installation.
WARNING: This product can expose you to chemicals including lead, which
are known to the State of California to cause cancer or birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov.
REFER TO GARAGE DOOR OPENER MANUAL FOR DETAILED INSTALLATION, ADJUSTMENTS, AND SAFETY INFORMATION. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
- Install keypad within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.
- Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
- ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
PREPARE
PROGRAM INITIAL PIN
To program the keypad to more than one garage door opener, repeat the steps above using a new PIN for each additional garage door opener.
CHANGE AN EXISTING PIN*
- For garage door openers that have a green Learn button or an external receiver repeat “Program Initial PIN” to change the existing PIN.
PROGRAM A TEMPORARY PIN
NOTE: This feature is not available on garage door openers that have a green
Learn button or an external receiver.
A temporary 4-digit PIN can be programmed to allow access to visitors. Each
programmed PIN can program one temporary PIN. The temporary PIN can be set for
a number of hours or a number of door openings. The temporary PIN cannot be
the same as any previously programmed PIN.
To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3.
- Select a location to mount the keypad at a minimum height of 5 the bottom screw. Do not overtighten to avoid cracking the plastic housing.
- Remove battery cover and battery.
- Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.
- Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the keypad over the top screw.
- Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing.
- Reinstall battery and replace cover.
OPERATION
The garage door opener activates when the PIN and ENTER button are pressed.
The keypad will blink for 15 seconds, during that time the ENTER button can be
used to stop, start or reverse the door.
If the wrong number is accidentally pressed, press the correct PIN then the
ENTER button. The keypad will transmit only the last four digits that were
pressed before the ENTER button.
ONE BUTTON CLOSE: The keypad has a feature that allows the door to be
closed using the ENTER button instead of a PIN.
NOTE: This feature is not available on garage door openers manufactured prior
to 2006 or an external receiver.
To deactivate the one button close feature:
- Press and hold the 1 and 9 buttons for 10 seconds.
- The keypad will blink four times when the one button close feature is deactivated.
To activate the one button close feature:
- Press and hold the 1 and 9 buttons for 10 seconds.
- The keypad will blink twice when the one button close feature is activated.
REPLACEMENT PARTS
- 9V Battery . . 10A25
- Keypad cover . . 41D621
- Battery cover . . 41D541
BATTERY
To prevent possible SERIOUS INJURY or DEATH:
- NEVER allow small children near batteries.
- If battery is swallowed, immediately notify doctor.
Replace the battery when the keypad becomes dim or does not light after a
button is pressed.
Dispose of old battery properly.
FCC rules
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or
modifications of this receiver and/or transmitter are prohibited, except for
changing the code setting or replacing the battery. THERE ARE NO OTHER USER
SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation
is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Call: 888-331-4569
www.craftsman.com
Download PDF:Craftsman Garage Door Opener Keypad CMXZDCG440 User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>