Transcend A1D Universal Composite Shade Instruction Manual

Transcend A1D Universal Composite Shade Instruction Manual

Transcend Universal Composite

Product Description

Transcend™ universal composite is a light-cured, tooth shade resin composite material (Bis-GMA-based) to be used for direct and indirect posterior and anterior tooth restorations. Transcend universal composite is radiopaque and available in a range of dentin, enamel, and body shades. It is 79% filled by weight and 60-61% filled by volume and has an average particle size of 0.9 μm (by weight) with narrow upper limit particle distribution.

Shade Guide
A1D, A2D, A3D, B1D| A1, A2, A3, B1|
Enamel White (EW) Enamel Neutral (EN)| | OM2 OM3

Universal Body (UB)

| An average dentin shade designed to take on the shade of the surrounding tooth structure

“:Lk/jnfnVITA, VITA classical A1-D4, and 3D-MASTER are registered trademarks of VITA Zahnfabrik H. Rauter GmbH & Co. KG.

For all products described, carefully read and understand all instructions and SDS information prior to use.

Delivery Form(s)

• 4 g multi-use syringe
• 2 g single-use capsule

Composition

1 – 21 wt% each: dimethacrylate resin, methacrylate resin 60 – 90 wt%: silica, silane treated silica

Indications for Use/Intended Purpose

Transcend universal composite is used for direct and indirect restorations in both the anterior and posterior regions.

Contraindications

• Do not use on patients with known sensitivity to methacrylates or other If dermatitis, rash, or other allergic reaction is observed, rinse exposed area thoroughly and have patient consult their physician.
• For patients or users with allergy concerns, refer to product allergen document available at ultradent.com. If allergic reaction is observed, rinse exposed area thoroughly with water and have the patient consult their physician.

Warnings and Precautions

• Resins can be Do not use on patients with a known sensitivity to acrylates or other resins. If allergic reaction, dermatitis or rash develops, have patient consult their physician.
• Syringes are not for intra-oral
• To avoid cross-contamination, use clean gloves and a clean
• Redirect overhead light to prevent premature
• To optimize bond to each succeeding layer, do not remove oxygen inhibition layer between incremental layers of
• Ensure composite is totally polymerized between

Stepwise Instructions Preparation

1)   Apply dentin bonding agent to preparation according to manufacturer’s instructions.

Use – Direct Restoration

• Open cap and twist handle (stem) clockwise to express desired amount of Resistance will lessen with each twist
• Place Transcend universal composite in incremental layers applying the first layer approximately 0.5 – 1.5 mm thick and Follow with up to 2 mm increments; curing after each increment. For curing lights with an intensity of ³ 800 mW/cm2 in the wavelength region of 385-515nm, cure each layer for 10 seconds. A final cure of 20 seconds is recommended.
• After final increment is placed, sculpt and light
• Shape, finish, and adjust occlusion using preferred method.
• Immediately replace cap after dispensing composite to prevent polymerization from ambient

Use – Indirect Restorations

• Make impression of prepared tooth and opposing
• Prepare master cast and articulate opposing cast using preferred
• Place Transcend universal composite in incremental layers applying the first layer approximately 0.5 – 1.5 mm thick and Follow with up to 2 mm increments; curing after each increment. For curing lights with an intensity of ³ 800 mW/cm2 in the wavelength region of 385-515nm, cure each layer for 10 seconds.
• Use final increments to create proximal contours and ensure marginal adaptation, a final cure of 20

seconds is recommended.

• Remove Clean off residual die stone and trim marginal flash. Additions can be made by

roughening restoration surface, applying adhesive, and placing Transcend universal composite as needed.

• Sandblast internal aspect of restoration with 50 µm alumina
• Seat restoration onto master cast, evaluate fit, occlusion, and Shape, finish, and adjust occlusion

using preferred method.

• Bond restoration intraorally per adhesive manufacturer’s
• Following cementation, make necessary occlusal adjustment and polish adjusted

Use – Singles (capsule), Direct Restoration

• Keep capsule caps on until
• Snap capsule firmly into composite gun before trying to
• Unit dose capsule are designed for single patient use only. Do not reuse to avoid the risk of cross Discard capsule after use.
• Place composite in incremental layers applying the first layer approximately 5 – 1.5mm thick and cure. Follow with up to 2 mm increments; curing after each increment. For curing lights with an intensity of ³ 800 mW/cm2 in the wavelength region of 385-515nm, cure each layer for 10 seconds. A final cure of 20 seconds is recommended.
• After final increment is placed, sculpt and light
• Shape, finish, and adjust occlusion using preferred method.

Storage and Disposal

Dispose of waste according to local rules, guidelines, and regulations.

Miscellaneous Information

Report any serious incident to the manufacturer and the competent authority. 800-552-5512/801-572-4200">www.ultradent.com / 1-800-552-5512 / 801-572-4200

Read More About This Manual & Download PDF:

References

• Ultradent Products, Inc.
• Ultradent Products, Inc.
• Ultradent Products, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>