edisio ED-SH-03 Wireless Switch Instruction Manual
- June 4, 2024
- edisio
Table of Contents
ED-SH-03
Mini module lighting, dry contact, and pulse
Instruction Manual
Install the module
!! Warning !! Turn off the power before handling. If in doubt about your
installation, please consult your electrician.
1.1 Connect the ED-SH-03 module to a luminaire
Connect the module to the luminaire by placing the Neutral cable (blue) in the
N terminal, and the phase (brown) in the terminal (O2). Connect the module to
the power supply by placing the neutral (blue) cable in the N terminal, and
the (brown) phase in the terminal (L). Connect then the second terminal (L) to
the connector (01).
1 .2 Connect the module to a push button or a classic switch
By default, the module is configured for a classic or a toggle switch, if you
have a push switch, press 9x on the R button of the module.
Press the R button again 9x to return to the classic button mode.
Connect your push button or switch to the terminal L and at the terminal S
1.3. Connect the module to a gate or an electric lock
Connect the module to the power supply by placing the Neutral cable (blue) in
terminal N, and the phase (brown) in terminal (L). Connect your gate to
terminals 0, and 02 To put your module in pulse mode, press the R button 8
times. Press again 8x on the R button to return to On / Off mode. By default,
the module is configured in a 0.5-second pulse, if you want a 4-second pulse,
press the R button 3x. Press the R button 3x again to return to 0.5 pulse mode
Associate with an Edisio command
Press the R button on the Edisio module once. Within 10 seconds, press the switch button. Within 10 seconds, press the R button on the module again.
Clear the link with a Edisio command
Press the R button on the Edisio module for 5 seconds. Within 10 seconds, press the key to be erased from the switch. Within 10 seconds, press the R button on the module again.
Advanced modes
By default or after reset, the timer and the repeater are deactivated and the
module is in light mode
Reset:
To reset the module to factory mode, press the R button for 10 seconds. The
lead flashes quickly to confirm.
Timer:
It is possible to activate a timer on the module so the connected device
automatically turns off after the time limit. Several timers are possible: 2
minutes : Activate: 3xR => the led flashes 3x slowly to confirm.
Disable: 3xR => the led flashes 3x quickly to confirm. 5 minutes: same as 4xR
/ 10 minutes: same as 5xR / 30 minutes: same as 6xR / disabled by default
Signal repeater (meshing):
To extend the radio range between your devices, you can enable this function.
By default, the function is disabled in order to optimize the response time of
the module. Activate: 7xR => the led flashes 7x slowly to confirm. Disable:
7xR => the led flashes 7x quickly to confirm. Do not activate more than 5
“meshing” receivers per installation.
Remove the R button:
If you have difficulty accessing the module after installation we advise you
to shift the R button to the E button of an edition switch. Activate: 2xR =>
Press button E of the switch => the led flashes 2x to confirm. The switch
becomes Master. You can now pair other remote controls
Technical characteristics
ED-SH-03
Protocol: edition Frequency: 868.3MHz Max Power: 3 mW EIRP Transmission range:
150m (in free field) Max. 32 associated transmitters Operating temperature: -5
to 50 ° C Power supply: 230V — 50Hz
Max .: – 8.5A (cos φ = 1)
– resistive load: 2000W
– LC loads (LED): 500W (Max 10 bulbs) hxwx d: 40x40x2Omm
Indoor use (IP20), do not use in a humid environment.
| For indoor use only
---|---
| Alternating current
Supplementing your installation
Supplement your installation with Edisio solutions to control your heating, lighting, roller shutters, or garden. Easy, high-quality, scalable, and economical…learn about all of the Edisio solutions at www.chacon.com
Recycling
In accordance with the European WEEE (2002/96 / EC) and Battery Directive
(2006/66 / EC), all electrical, electronic or accumulator devices must be
collected separately by a local and specialized waste collection system. Do
not dispose of these products with ordinary garbage. Consult the regulations
in force. The garbage mark indicates that this product should not be disposed
of with household waste in any EU country. To prevent any risk to the
environment or human health from uncontrolled disposal, recycle the product
responsibly to promote the sustainable use of material resources. To return
your used device, use the return and collection systems or contact the
original dealer. He will carry out the recycling in the respect of the
regulatory provisions.
CHACON declares that the ED-SH-03 complies with the essential requirements and
other relevant provisions of the RED 2014/53 / EU Directive. The complete text
of the EU declaration of conformity is available at the following Internet
address: www.chacon.be/en/conformity
www.chacon.com/conformity
Support
****www.chacon.com/support
V6.2 220509
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>