Kydera KT-8900 Mini Dual Band Car Radio User Manual

Kydera KT-8900 Mini Dual Band Car Radio

EXPLICIT DEFINITIONS

• It is important that the operator is aware of and understand hazards common to the operation of any transceiver.
• Explosive environment (such as gases, dust, fumes, etc.)
• Turn off your transceiver while taking on fuel, or while parked in gasoline service stations.

MATTERS NEED ATTENTION

Please observe the following precautions to prevent fire, personal injury, damage to the radio:

• Don’t use this machine when driving, so dangerous.
• This radio is designed to use 13.8 V de voltage, do not use the 24 V power supply to the power supply.
• Please do not place the machine in the dust, moisture or water splashing.
• If you accept received external disturbance, should make the machine away from jamming equipment.
• Do not use the captain time exposed to direct sunlight or heating equipment accessories.
• If the unit emitting smoke or strange smell, should immediately cut off power supply, No later to confirm the machine safety, sent to the nearest repair service station to check it.
• Don’t for a long time with high power output for launch, which could lead to walkie talkie is overheating.

UNPACKING AND INSPECTING EQUIPMENT

Welcome to use the wireless interphone, before use, it is recommended that you:

• Please check the packaging of this product have any signs of damage.
• Please confirm box carefully opened the box, if any items listed in the table below.
• If you find this product and its accessories in the handling of any lost or damaged, immediately contact the dealer.

Standard accessories

PANEL DESCRIPTION

1. 1 Progress of the knob
2. Transmit indicator
3. Function keys
4. Call key
5. Monitor function
6. 6 Powerkey
7. Power indicator
8. Volume Knob
9. Microphone Connector
10. FM radio function key
11. Exit the AB signal switching, alarm function 12 Channel switching
12. channel Switching
13. Display screen
14. Data Terminal

Hotkey function guide

• [F]: click to enter menu select mode.

• [ CALL ]: in standby mode, press to send caller ID at selected signaling mode. in transmit mode, press to send
  repeat activate signaling.

• [MONI]: press to turn on the squelch, repeat to turn off the squelch.

• [ ]: hold the key to turn on and turn off the radio power.

• [VM]: press to select channel mode and frequency mode.

• [EXIT/AB]: press to choose NB frequency and exit function mode.

• [FM]: press to enter and exit FM radio function.

MENU FUNCTION SETTING

Menu function setting (Can setting by mic­keypad)

1. [F Key]+[0 Key] : TDR turn on/off dual frequency standby setting. ON can both AJB frequency standby at same time. OFF only for frequency you selected. Use [F Key] to savesetting.
2. [F Key]+[1 Key]: STEP setting the step figure at frequency mode, 5KHZ, 6.25KHZ, 1 0KHZ, 12.5KHZ, 25KHZ available. Use [F Key] to save the setting.
3. [F Key]+[2 Key]: SQL receiver squelch setting. 10 level, 0 is turn on the squelch, 1-9 to adjust level, use [F Key] to save setting.
4. [F Key]+[3 Key] : TXP transmit output power setting. HIGH/LOW use F Key to save setting.
5. [F Key]+[4 Key]: SCR Scrambler setting. Acti­vating voice scrambling avoids the user’s speech being overheard by user without using scrambling function. (Optional)
6. [F Key]+[S Key]: TOT transmission time-out timer. Setting transmit time from 15 to 600 seconds by 15 step. Use [F Key] to save setting.
7. [F Key]+[6 Key]: TOA transmit over alarm setting. OFF is close function. Set from 1-10 seconds, use [F Key] to save setting.
8. [F Key]+[7 Key]: WN WIDE/ NARR band width setting. Use [F Key] to save setting.
9. [F Key]+[S Key]: ABR LCD light time setting. OFF is to close the function stay LCD light working. Set by 1-50 seconds, us [F Key] to save.
10. [F Key]+[9 Key]: BEEP function key guide voice. OFF/ON
11. [F Key]+[1 Key]+[0 Key] : R-DCS DCS receive setting. D023N-D754N positive sequence, D023I­D754I reversed sequence. Use [F Key] to save setting.
12. [F Key]+[1 Key]+[1 Key]: R-CTCS CTCS receive setting. 67.0HZ-254.1 HZ or can use keypad to enter your target CTCS. Use [F Key] to save setting.
13. [F Key]+[1 Key]+[2 Key]: T-DCS transmit DCS setting. D023N-D754N positive sequence. D023I­D754I reversed sequence. Use [F Key] to save setting.
14. [F Key]+[1 Key]+[3 Key]: T-CTCS transmit CTCS setting. 67.0HZ-254.1 HZ or can use keypad to enter your target CTCS. Use [F Key] to save setting.
15. [F Key]+[1 Key]+[4 Key]: DTMFST DTMF side tone setting. OFF: Close function. KEY: Sound code voice only when radio transmit DTMF code. ANI: Sound code voice when automvatic code mode. BOTH: Sound code voice at both mode.
16. [F Key]+[1 Key]+[S Key] : BCL busy channel lock­out. OFF: transmit at busy channel. ON: no-transmit at busy channel. Use [F Key] to save setting.
17. [F Key]+[1 Key]+[6 Key]: SC-ADD scan add setting. OFF: store channel without add to scan list. ON: store channel and add to scan channel list. Use [F Key] to save setting.
18. [F Key]+[1 Key]+[7 Key]: PRI-SC priority scan setting. ON/OFF turn on/off the function. Use [F Key] to save setting.
19. [F Key]+[1 Key]+[S Key] : PRI-CH priority channel scan setting. Select 000 -199 channels mark with CH at front to priority scan. Use [F Key] to save setting.
20. [F Key]+[1 Key]+[9 Key]: SC-REV Scan recover setting. TO: lime scan, after receive carrier signal will stop scan and rescan after a while. CO: after receive carrier signal will stop scan. SE: Search scan mode. Scan will stop after receive according signal with radio.
21. [F Key]+[2 Key]+[0 Key]: OPTSIG Signal option setting. OFF turn off the function. DTMF: dual channel signal selected mode. 2TONE: 2 tone signal mode. STONE: 5 tone signal mode. Use [F Key] to save setting.
22. [F Key]+[2 Key]+[1 Key]: SPMUTE speaker mute setting. QT: turn on the speaker when receive setting DCS. If no setting DCS then will turn on the speaker when receive carrier signal. AND: speaker turn on only DCS and option signaling both meet radio setting. OR: speaker turn on either DCS or option signaling meet with radio setting. Use [F Key] to save setting.
23. [ F Key]+[2 Key]+[2 Key]: PTT-ID PTT-ID transmit setting. OFF: no send ID code when transmit. BOT: send ID code when transmit. EOT: send ID code after transmit. BOTH: send ID code both start transmit and transmit finish. (ID code is signal information code by PC software setting, from menu 24 to select ID code) use [F Key] to save setting.
24. [F Key]+[2 Key]+[3 Key]: PTT-LT PTT-ID transmit delay setting. Set delay lime during 0-30 seconds. Use [F Key] to save setting.
25. [F Key]+[2 Key]+[4 Key]: S-INFO Signal informa­tion and automatic dialing memory. 1-15 group signal code/decode memory. Only can set by PC software.
26. [F Key]+[2 Key]+[S Key]: EMC-TP alarm mode setting. ALARM: turn on the alarm sound. ANI: send alarm code and ID code. BOTH: both above. Use [F Key] to save setting.
27. [F Key]+[2 Key]+[6 Key]: EMC-CH alarm channel setting. Channel set CH ahead when alarm is effective channel. Use [F Key] to save setting.
28. [F Key]+[2 Key]+[7 Key] : RING-T Ring lime setting. OFF: close function. Choose 1-10 seconds to set ring lime when radio got match signal code. Use [F Key] to save setting.
29. [F Key]+[2 Key]+[S Key]: CHNAME channel name edit. Use function under channel model.
30. [F Key]+[2 Key]+[9 Key]: CA-MDF Channel A setting. FREQ: channel show frequency at channel mode. CH: channel show channel list at channel mode. NAME: channel show channel name at channel mode.
31. [F Key]+[3 Key]+[0 Key]: CB-MDF Channel B setting. FREQ: channel show frequency at channel mode. CH: channel show channel list at channel mode. NAME: channel show channel name at channel mode.
32. [F Key]+[3 Key]+[1 Key]: AUTOLK Automatic lock-out setting. OFF/ ON turn off/on the function. Use [F Key] to save the setting.
33. [F Key]+[3 Key]+[2 Key]: PONMSG Display mode setting. FULL: Full display when turn on the radio. MSG: appointed message display when turn on the radio. BATT-V Show battery power output voltage when turn on the radio. Use [F Key] to save setting.
34. [F Key]+[3 Key]+[3 Key]: WT-LED standby back light setting. OFF: close. BLUE: choose blue color. ORANGE: choose orange color. PURPLE: choose purple color. Use [F Key] to save setting.
35. [F Key]+[3 Key]+[4 Key]: RX-LED back light setting at receive. OFF: close back light. BLUE: choose blue color. ORANGE: choose orange color. PURPLE: choose purple color. Use [F Key] to save setting.
36. [F Key]+[3 Key]+[S Key]: TX-LED back light setting at transmit. OFF: close back light. BLUE: choose blue color. ORANGE: choose orange color. PURPLE: choose purple color. Use [F Key] to save setting.
37. [F Key]+[3 Key]+[6 Key]: MEM-CH channel me­mory setting. Show CH after you select channel to memory. Use [F Key] to save setting.
38. [F Key]+[3 Key]+[7 Key]: DEL-CH channel delete setting. CH will disappear after you select the channel and use channel delete function. Us [F Key] to save setting.
39.   [F Key]+[3 Key]+[B Key]: SFT-D Frequency differ­ence direction setting. OFF: no frequency difference at frequency mode. +: transmit frequency figure equal receive frequency figure add frequency difference figure at frequency mode. -: transmit frequency figure equal receive frequency figure minus frequency difference figure at frequency mode. Use [F Key] to save setting.
40. [F Key]+[3 Key]+[9 Key]: OFFSET frequency difference figure setting. Can choose figure during 00.000-69.990MHZ under frequency mode. Use [F Key] to save setting.
41. [F Key]+[4 Key]+[0 Key]: ANI radio ID code. Code only can set by PC software.
42. [F Key]+[4 Key]+[1 Key]: ANI-L ID code length. Can choose 3.4.5 length, use [F Key] to save setting.
43. [F Key]+[4 Key]+[2 Key]: REP-S repeater activate setting. 1000: under transmitting press Call to send 1 KHZ frequency signal to activate the repeater. 1450: under transmitting press Call to send 1 .45 KHZ frequency signal to activate the repeater. 1750: under transmitting press Call to send 1.75 KHZ frequency signal to activate the repeater. 2100: under transmitting press Call to send 2.1 KHZ frequency signal to activate the repeater. Use [F Key] to save setting.
44. [F Key]+[4 Key]+[3 Key]: REP-M repeater forwar­ding mode setting. OFF: close function. CARRI: forwarding after receive carrier. CTDCS: forwarding after receive correct CTDCS. TONE: forwarding after receive correct mono audio. DTMF: forwarding after receive assigned DTMF code. Use [F Key] to save setting.
45. [F Key]+[4 Key]+[4 Key]: RESET Initialization Setting. VFO: reset the menu setting to initialization setting. ALL: reset the menu setting and channel setting to initialization setting. Press [EXIT/AB] after menu setting.

Operation for manual channel memory and delete

Channel memory:

1. Directly input frequency by keypad under frequency mode. Example: 435.125MHz input 4, 3, 5, 1, 2, 5.

2. Setting CTDCS frequency (manual page10, 11 ), Setting transmit CTDCS frequency (manual page12, 13). For example: receive CTDCS 67.0HZ, transmit CTDCS 67.0HZ. Press [F] Key+ [1] Key+ [1] Key
   + [F] Key+ [DOWN] Key, select 67.0HZ + [F] Key+[EXIT/AB] Key to save receive CTDCS frequency. Transmit CTDCS 67.0 HZ press [F] Key+ [1] Key+ [3] Key+ [F] Key+ [DOWN] Key, select 67.0HZ + [F] Key+ [EXIT/AB] Key to save transmit CTDCS frequency. (select OFF if no need CTDCS)

3. See manual 36 to memory the channel, press [F] Key + [3] Key+ [6] Key+ [F] Key+ [UP] (DOWN) select channel + [F] Key to memorize the channel information.

Channel delete:
See manual 37 for channel delete. Press [F] Key + [3] Key + [7] Key + [F] Key + [UP] (DOWN) select the channel number+ [F] Key delete the channel.

Memory FM radio channel

Use PC software to edit FM radio channel. (software FM option) Under transmit send DTMF code by micro­phone keypad. Press the microphone [*] Key to search FM channel under FM mode.
Keypad Lock-out
Hold the microphone [# key] for 2 seconds at standby to turn on/off the keypad lock-out function.
Transmit transit signal
Select transit signal frequency (our radio have 4 kind transit signal frequency). Press [F] Key + [4] Key + [2] Key + [F] Key + UP(DOWN) select transit signal fre­quency + [F] Key save. Hold the [PTT] Key and press the [Call] Key to transmit setting transit signal.
PTT ID Setting
Use PC software to edit PTT-ID code.

1. See manual 20, select signal, Press [F] Key + [2] Key + [O] Key + [F] Key + [UP] (DOWN) select signal + [Fl Key save the setting.
2. See manual 22, setting PTT launch. Press [F] Key + [2] Key + [2] Key + [F] Key + [UP] (DOWN) select PTT-ID transmit time + [F] Key save setting.
3. See manual 23 setting PTT transmit delay time. Press [F] Key+ [2] Key+ [3] Key+ [F] Key+ UP select delay time + [Fl Key save setting.
4. Press [PTT] to send setting ID code.

Optional signal setting

DTMF signal setting
This radio have DTMF coding/decode function, use PC software to input code information.
DTMF signal
setting receive DTMF signal first, after receive the same code as your setting radio will show the code by display and ring. Then can speech during effective time. (ID code setting by PC software)
Inspect function
When receive DTMF code is same as setting inspect code receiver will send ID code. Screen can display this code. This function can setting if control by master ID, can no control by receive signal. (Inspect code can set by PC software)
Monitor function
When receive DTMF signal is same as setting code, receiver will turn on the monitor function for nearby signal. This function can setting if control by master ID, can no control by receive signal. (Monitor code can set by PC software)
Remote stun
When receive DTMF signal is same as pre-set remote stun code, receiver will turn off transmit function, only can work at receive. And LCD will display remote stun information. Only after receive turn on code the radio will turn on the transmit function. This function can setting if control by master ID, can no control by receive signal. (remote stun code can set by PC software)
Remote Kill
When receive DTMF signal is same as pre-set remote kill code, receiver will turn off all function, and LCD will display remote kill information. Only after receive turn on code the radio will turn on all function. This function can setting if control by master ID, can no control by receive signal. (remote kill code can set by PC software)

Turn on function
When receive DTMF signal is same as pre-set turn on code, receiver will cancel remote stun or remote kill. This function can setting if control by master ID, can no control by receive signal. (Turn on code can set by PC software)
Alarm function
When receive DTMF signal is same as pre-set alarm code, receiver will turn on the alarm function. Alarm mode and alarm channel can set by PC software optional edit. This function no control by master ID and no control by receive signal. (Alarm code can set by PC software) Signal control by master ID means function only work by signal code and master ID both confirm. No control by master ID coding format: signal code +# (patch code)+information code. Control by master ID coding format: signal+#(patch code)+ master ID code+#(patch code)+information code.

DTMF transmit by Call Key setting

1. Select DTMF signal, press [F] Key+ [2] Key + [O] Key + [F] Key + UP(DOWN) select DTMF signal +
   [F] Key save setting.

2. Select signal information code. Press [F] Key + [2] Key+ [4] Key+ [F] Key+ UP(DOWN) select decode signal information code group (1-15) + [F] Key save the setting. (Can use PC software set DTMF code).

3. Press [Call] Key transmit selected DTMF code group at standby.

2 tone and 2 tone signal transmit by Call Key setting

1. Press [MENU] Key select 20 OPTSIG, press [F] Key select 2TONE function.
2. Press [MENU] Key select 24 S-INFO, press [F] Key select pre-code signal group(1-16). (Can use PC software setting 2 tone)
3. Corresponding function will turn on when receive 2TONE signal is same as pre-set 2TONE code.
4. Press [Call] Key to send 2TONE group code at standby.

STONE signal setting
This radio have STONE coding/decode function. You can use PC software to input signal information code. Set STONE signal then after receive same same STONE signal code receive and turn on the ring function and display the information code. Speech at effective lime is available. (ID code can use PC software to setting).

• Press [CALL] Key to transmit STONE
• Press [MENU] Key, select 20 OPTSIG press [F] Key select STONE function.
• Press [MENU] Key, select 24 S-INFO press [F] Key select pre-code signal group 1-16. (Can use PC software setting STONE information code, each group can transmit 3 group STONE code for optional).
• Press [CALL] Key transmit pre-set STONE code group at standby.

HAND THE Ml DESCRIPTION

• CD “MENU”: Function keys
• “UP” : Higher frequency
• “DOWN” : Lower frequency
• “EXIT” : Exit the AB channel switch, alarm function @ “/SCAN”: Pour, scanning and digital frequency function, digital
•  “ #/LOCK “: Keyboard lock function, digital #
• “O” : Number O
• “ 1 “: Number 1
• “ 2 “: Number2
• “ 3 “: Number3
• “ 4 “: Number4
• “ 5 “: Numbers
• “ 6 “: Number6
• “ 7 “: Number?
• “ 8 “: Numbers
• “ 9 “: Number9

FUNCTION MENU

secondary menu Settings
0| TOR| D-frequency waiting| OFF| Close the double- frequency waiting
ON**| Start the dual- band waiting
 |

STEP

|

Step frequency

| 5.00K|

In frequency mode, press the UP, DOWN, change the frequency of the step value

6.25K
10.00K
12.50K
25.00K
2| SOL| Squelchstep| 0,···,9| Squelch Step
3| TXP| Transmitted power| HIGH| high power transmitter energy
LOW| Small power emission
4| SCR| Voice encryption| OFF| Close the voice encryption
ON| Open the voice encryption
5| TOT| Time| 15,30,–· 600| Numbers from 15 to 600. With 15 step by step,
6| TOA| Launch end early warn| OFF| Closed end early warning
1,2,..10| Launch for the rest of the end,this time indicator light will flash
7| WN| EAJ| WIDE| Broadband work
NARR| Narrowband work
8| ABR| Auto light| OFF| Shut down automatically light
1,2,3,4,.. · 50| On the backlight to automatically shut down time
9| BEEP| Voice to switch| OFF| Closing beep
ON| Open the prompt to operate
10| R-DCS| Receive retuned| OFF| No retuned
D023N,–· ,D75 4I| Digital retuned the standard sequence

11

| R-CTCS| Receive analog retuned| OFF| No retuned
67 .0 HZ,–· ,25 4.1HZ| Simulation retuned the standard sequence
 |  |  |  |
12| T-DCS| Launch digital

retuned

| OFF| No retuned
---|---|---|---|---
D023N,•· •,D 7 54I| Digital retuned the standard sequence

13

|

T-CTCS

| Launch simulation

retuned

| OFF| No retuned]
67.0HZ,···,254.1HZ| Digital retuned the standard sequence

14

|

DTMFST

|

Lateral sound switch

| OFF| To launch time, DTMF key launch, the machine does not send out the voice of the code
KEY| At launch time, the key launch DTMF, native sound
ANI| At launch time, automatically send code, the machine is sound
BOTH| Launch time, the key code and code automatically, the machine is sound
15| BCL| No launch| OFF| Channels are also allowed to launch
O N| Channel occupied launch is prohibited
16| SC-ADD| Add Scan Channel| OFF| Storage channel, the channel is not added to the storageby the scanning list
ON| Storage channel, the channel is added to the storage by the scanning list
17| PRI-SC| Priority scan| OFF| Priority scanning function to shut down
ON| Priority scanning function

18

|

PRI-CH

| Priority channel|

000,-··, 199

|

Priority scanning open channel show a CH fo r effective channel

19

|

SC-REV

|

Scan back way

| TO| Scan time way
co| Carrier way to scan
SE| Search to scan

20

|

OPTSIG

|

Optional signaling

| OFF| Close the optional signaling
DTMF| The current optional signaling of DTMF signal
2TONE| The current optional signaling is 2 tidings
5TONE| The current optional signaling is 5 tidings

21

|

SPMUTE

| horn loudspeaker| QT| Retuned match open the horn
A ND| Retuned and optional signaling match at same time open horn
OR| Retuned or optional signaling a match or open the horn

22

|

PTT-ID

|

PPT launch

| OFF| Press the PPT is not yards
BOT| Press the PPT is yards
EQT| ON the PPT is not yards
 |  |  |  |
22| PTT-ID| PPT launch| BOTH| Press and release PPT are sending
---|---|---|---|---
23| PTT-LT| Sending additiona| 0,1,··· ,30| Befo re sending the delay time of automatically
24| S- INFO| S information| 1,” ·,15| Need,lssuethe information code

25

| ****

EMC- TP

| ****

Alarm Mode

| ALARM| Sound an alarm when the machine is warning tone
ANI| Send an alarm when alarm code and native identity code
BOTH| Alarm, give tones sent identity code at the same time
26| EMC- CH| Akarm channel| 000,” ·,199| Alarm, specified alarm channel, channel show CH ahead effective
27| RIN G- T| Ring time| OFF,1,2,.. ·10| Receiving matching signaling, tones this machine is call open horn
28| CHNAME| Channel name edit|  | In the channel mode, edit the current channel name

29

| ****

CA- MDF

| A chann el di splay mode| FREQ| A section of the channel mode, channel frequency display
CH| A section of channel mode, the channel to channel number display
N AM E| A section of the channel mode, channel by channel name display

30

| ****

CB- MDF

| B channel display mode| FREQ| B section of the channel mode, channel frequency display
CH| B section of channel mode, the channel to channel number display
N A M E| B section of channel mode, the channel to channel number display
31| AUTOLK| KeyLock| OFF| Close the keyboard lock autornatically
ON| Open the keyboard automatic locking function
32| PONMSG| Boot mode| FULL| Full screen
MSG| The specified information

33

| ****

WT-LED

| ****

Standby light choice

| OFF| Close the backlight
BLUE| Open the blue light under the standby
ORAN GE| Open the Orange light under the standby
PURPLE| Open the pupple light under the standby

34

| ****

RX- LED

| ****

Receiving light choice

| OFF| Close the backlight
BLUE| Open the blue light receiving condition
ORANGE| Open the Orange light receiving condition
PURPLE| Open the Pupple light receiving condition
 |  |  |  |

35

|

TX-LED

|

Transmit light choice

| OFF| Close the backlight
---|---|---|---|---
BLUE| Open the blue light emission condition
ORANGE| Open the Orange light emission condition
PURPLE| Open the Pupple light emission condition
36| MEMCH| Channel memory| 000 ,···,199| When storage channel, indicates channel number is stored, if d igi tal display CH – in front of it, said that original channel storage parameters

37

|

DELCH

| Erasure channel| 000,–· ,199| Delete specified channel parameters, ii no CH – front, is invalid

38

|

SFT-D

| Frequency offset

direction

| OFF| Frequency transmitting freq u ency and receive frequency no difference
+| Frequency mode, the launch is receiving and frequency offset
 | Frequency mode, launch is equal to receive frequency subtraction
39| OFFSET| Frequency direction| 00.000,···,69.990| Frequency mode, the transmitting and receiving of the poor
40| ANI| Code|  | The status code is used to observe the machine Settings
41| ANI-L| ANI Length| 3,4,5| Effective length of the native identity code

42

|

REP-S

|

Repeater activate

| 1000| Launch,call single frequency tone frequency,fo r exciting relay station
1450| Launch,call single freque ncy tone frequency,fo r exciting relay station
1750| Launch.call single frequencytone frequency.for exciting relay station
2100| Launch,call single frequency tone frequency,for exciting relay station

43

|

REP-M

|

Repeater Mode

| OFF| Close the relaying
CARRI| Receive forwarded to the carrier
CTDCS| Receives the dumb tidings to forward
TONE| Forwarding receives the mono audio channel
DTMF| Receive the specified forwarding when DTMF code
44| RESET| Initialize| VFO| Menu to initialize
ALL| Menu and channel initialization

THE KEV TECHNICAL INDEXES

General specification

Frequency range| VHF: 136~174MHz 245~245.9875MHz(220~260MHz)

UHF: 400~480MHz 480~520MHz

---|---
Number Of Channels| 200
Channel Spacing| 25KHz 20K 12.5
Phase lock step step| 5KHz, 6.25KHz, 10KHz, 12.5KHz, 15KHz, 25KHz,
Working Voltage| 13.BV DC± 15%
Squelch way| CTCSS I DCS I 5Tone / 2Tone I DTMF
Frequency stability| ±2.5ppm
Operat Temperature| – 20~+60°C
Dimension| 98 ( W ) x 35 ( H ) x118 ( D ) mm
Weight| 408g
Receiver (ETSI EN 300 086 Standardized.Test)

 | Broadband| Narrow band|
Sensitivity| :s; Q.25µ V| :s;Q.35µ V
Channel choice| ;;e ?0d B| ;;e 60dB
Intermodulation| ;;e 65d B| ;;e 60dB
Spurious Rejection| ;;e ?0d B| ;;e ?0dB
Audio response| +1~-3dB (0.3~3KHz)| +1~-3dB (0.3~2.55KHz)
Signal to noise ratio| ;;e 45dB| ;;e 40dB
Audio Distortion| :s; 5%
Audio output power| ;;e 2 W @10%
Transmit (ETSI EN 300 086 Standardized.Test)
 | Broadband| Narrow band|
Output power| 25W/20W(VHF/UHF)
Modulation Mode| 16KcDF3E| 11KcDF3E
Channel Power| ;;e ?0d B| ;;e 60 B
Signal to noise ratio| ;;e 40dB| ;;e 36dB
Parasitic harmonic| ;;e 60d B| ;;e 60dB
Audio response| +1~-3dB (0.3~3KHz)| +1~-3dB (0.3~2.55KHz)
Audio distortion| :s; 5%
Attention: There may be more changes, all the rules forgive not in addition to notice or liability

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>