Electrolux KOCDH76X 60 cm Steam Oven User Manual

June 11, 2024
Electrolux

KOCDH76X 60 cm Steam Oven
User Manual

WARNING
The appliance must not be installed behind a decorative doororder to avoid overheating.
To avoid any potential hazard, you must follow our instructions when you install your appliance. Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution.

  • This appliance must be installed by an authorized person according to all codes and regulations as in the local municipal building code and other relevant statutory regulations.

  • Wiring connections must be in accordance with AS/NZS 3000 Wiring Rules and any particular conditions of the local authority

  • Refer to the data plate for rating information. The data plate is positioned behind the oven door.

  • For appliances with open cooking surfaces, a disconnect functional switch should be provided near the appliance in an accessible position. Refer to AS/NZS 3000 clause 4.7.1

  • Wiring should be protected against mechanical failure.
    Refer to AS/NZS 3000 clauses 3.3.2.6, 3.9, 3.10

  • A means of disconnection with a contact separation of at least 3mm must be supplied in the fixed wiring.

  • This appliance must be connected with a cable of 75°C rating minimum.

  • This product has passed the insulation resistance test after manufacture. If the resistance reading is low at installation, it is probably caused by moisture from the atmosphere being absorbed by the elements after the appliance has been produced. (pass at 0.01MΩ AS/NZS 3000 Wiring Rules Clause 8.3.6.3).

WARNING
This appliance must be properly earthed.

  • Do not lift the appliance by the door handles.
  • Prepare the cupboard opening to match your appliance measurements. (See diagrams)
  • Slide the appliance into the cupboard, ensuring that the supply cable (where fitted) does not kink.
  • To prevent tipping, use the screws supplied to secure your appliance into the cupboard by fastening through the holes to the front panel.
  • The surrounding kitchen cabinets must be able to withstand 85°C. Electrolux WILL NOT accept responsibility for damage caused by installation into kitchen cabinets that cannot withstand 85°C.
  • If the appliance is to be installed adjacent to vinyl-wrapped surfaces, use an installation kit available from the vinyl-wrap supplier.
  • After installation, test and ensure that the appliance operates correctly before handing it over to the customer.

NOTE: If a powerpoint is fitted it must be accessible with the appliance installed, as the plug must be accessible after installation.

Cabinet construction for your appliance

For the best integration within a kitchen, install this appliance in a cupboard that gives a flush fit with the surrounding cupboard fronts. A recess of 20mm is ideal.
NOTE: Your  appliance must be mounted on a flat horizontal surface for the full width and depth of the product
NOTE: A ventilation slot 20mm wide is required at the rear of the  base of the cabinet floor.
NOTE: Refer to cooktop installation instructions for required clearance between cooktop and oven.

Electrolux EVEP916SB 90cm Built In Oven

Leveling oven

Place a level in the oven as below making sure the level sits on the front and rear forms. The level needs to be correct to prevent slides from moving in or out with gravity.Electrolux EVEP916SB 90cm Built In Oven - Figure
1

Hardwiring details

  1. Remove the terminal cover plate from the rear panel of the appliance.
  2. Fit wires through the hole in the step below the terminal cover panel.
  3. Engage wires into the plastic clip. Secure plastic clip with two long silver screws (supplied in separate bag).
  4. Replace the cover plate onto rear panel.

Electrolux EVEP916SB 90cm Built In Oven - Figure 2

For New Zealand Only:
The cooking range must be connected to the supply by a supply cord fitted with the appropriately rated plug that is compatible with the socket outlet fitted to the final sub-circuit in the fixed wiring that is intended to supply this cooking range.
Supply cord size required: EVEP916DSE – 4mm²

Electrical connection location – built-in models

Electrolux EVEP916SB 90cm Built In Oven - Figure 3

To access your detailed user manual simply scan the QR code on your smartphone or visit electrolux.com.au/support/manuals

https://DELIVR.COM/2FV2B-QR

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals