COVER POOLS Save-T 3 Automatic Pool Cover or Autosave Spa Cover Installation Guide
- June 11, 2024
- COVER POOLS
Table of Contents
COVER POOLS Save-T 3 Automatic Pool Cover or Autosave Spa Cover
Product Information
The Save-T 3 automatic cover system and Autosave spa cover are designed to
provide a convenient and safe way to cover your pool or spa. The product is
manufactured and sold by Cover-Pools Incorporated, located at 2580 S Decker
Lake Blvd, STE 300 West Valley City, UT 84119. The system is available in
different track styles and options to suit various pool designs and deck
materials.
The product must be installed and serviced by a licensed and qualified pool
equipment contractor or a professional with sufficient experience in pool
equipment installation and maintenance.
Product Usage Instructions
Before installing the Save-T 3 automatic cover system or Autosave spa cover, read and follow all warning notices and instructions that accompany the product. Failure to follow the instructions may result in property damage, personal injury, or death, and may void the warranty.
- Choose the appropriate track style and options based on your pool design and deck material.
- Ensure that the product is installed and serviced by a licensed and qualified pool equipment contractor or a professional with sufficient experience in pool equipment installation and maintenance.
- Follow the installation instructions carefully to ensure that the system is installed correctly.
- Use the product according to the instructions provided to ensure optimal performance and longevity.
- If you need additional copies of the instructions or have any questions about the product, visit www.coverpools.com or call 800.447.2838.
General Information for Installing a Save-T® 3 Automatic Pool Cover or
AutosaveTM Spa Cover
This is a general guide on factors to consider for the installation of a
Save-T 3 automatic cover system or Autosave spa cover.
Visit www.coverpools.com or call 800.447.2838 for
additional copies of all instructions.
WARNING
FOR YOUR SAFETY–This product must be installed and serviced by a contractor
who is licensed and qualified in pool equipment by the jurisdiction in which
the product will be installed where such state or local requirements exist. In
the event no such state or local requirement exists, the installer or
maintainer must be a professional with sufficient experience in pool equipment
installation and maintenance so that all of the instructions in this manual
can be followed
exactly. Before installing this product, read and follow all warning notices
and instructions that accompany this product.
Failure to follow warning notices and instructions may result in property
damage, personal injury, or death. Improper
installation and/or operation may void the warranty.
Cover-Pools Incorporated 2580 S Decker Lake Blvd, STE 300 West Valley City, UT
84119
800.447.2838 801.484.2724 www.coverpools.com
©2021 Cover-Pools Incorporated. All rights reserved. Cover-Pools® is a
registered trademark of Cover-Pools Incorporated.
All other trademarks referenced herein are the property of their respective
owners.
800024 Rel-0025
NOTES
Table of Contents
TRACK OPTIONS ………………………………………………………………………………………………………. 1
EXCAVATION AND PLUMBING …………………………………………………………………………………….. 3 Recessed
Mechanism–UndersideTM Track or Track Channel ………………………………….. 3 Recessed
Mechanism–Universal, SnapTopTM, or Flush Track …………………………………. 4
ELECTRICAL ……………………………………………………………………………………………………………. 5 Electric Motor w/
Toggle Switch (Standard Equipment)…………………………………………… 5 Hydraulic Power
System……………………………………………………………………………………… 5 Auto-Shutoff with Optional Accessory
Board/AquaLink® ………………………………………… 6 Auto-Shutoff with Accessory Board/AquaLink®
and Wireless…………………………………. 6
MECHANISM HOUSING………………………………………………………………………………………………. 7 Recessed Concrete,
Wood, or UPB Box–UndersideTM Track …………………………………… 7 Recessed Concrete, Wood,
or UPB Box–AutosaveTM OPTION 1: Conduit comes from back of
box…………………………………………………………… 8 Recessed Concrete, Wood, or UPB Box–AutosaveTM
OPTION 2: Conduit comes from side of box. ………………………………………………………….. 9 Recessed
Concrete, Wood, or UPB Box–Universal or SnapTopTM Track………………….. 10 Recessed
Wood Box Construction………………………………………………………………………. 10 Deck-Mounted Bench
Construction ……………………………………………………………………. 10
COPING AND DECK …………………………………………………………………………………………………. 11 Gunite
Layout–UndersideTM track………………………………………………………………………..11 Coping or Deck
Requirements–Underside track …………………………………………………..11 Coping or Deck
Requirements–Underside track (cont.) ……………………………………….. 12 Tile Beam–Underside
track ……………………………………………………………………………… 12
RECESSED BOX COVER ……………………………………………………………………………………………. 13
Brackets………………………………………………………………………………………………………….. 13 Vanishing LidTM System
………………………………………………………………………………………. 13 BezelTM lids
……………………………………………………………………………………………………….. 13
SPECIFICATIONS…………………………………………………………………………………………………….. 14
COVER SIZING AND PRICING…………………………………………………………………………………….. 15 Cost
Considerations………………………………………………………………………………………….. 16
TRACK OPTIONS
1 Based on the pool design, choose the appropriate track style and any
options.
actual size
UndersideTM Track · Mounted under deck coping · Anodized aluminum · Easier
installation and
replacement of rope
Deck Material
Deck Straps · For porous coping, brick,
flagstone, and materials less than 2″ thick · Mounted every 2′ of track · For
deck-on-deck pools
Form D
Track Channel
Reusable Coping Form
4″
· For concrete and
· For concrete, fiberglass
fiberglass pools
and vinyl-liner pools
3½”
· Raised-wall applications
· Eliminates the need for
· Track channel allows for
1-1/4″ foam or wood forms
custom cantilever profiles
· Extruded aluminum
· Foam or wood forms can
be incorporated for deck profiles
2-1/2″
Track Channel Inverted Mount · For any deck surface, such
as flagstone, slate or tile, that does not meet basic undertrack mounting
conditions (surfaces less than 2″ thick or softer materials)
41/4″ 11/4″
15/8″
Form B
2¾” 4″
Form A
Vinyl-Liner Pool Coping Undertrack System · For vinyl-liner pools · 90°, 45°,
6″ and 24″
corners available · Tracks locked in place
by shims · Standard or bullnose
coping options
4½”
Vinyl-Liner Pool
Track Channel
· Track channel allows for
custom cantilever profiles
· Foam or wood forms can
be incorporated for
deck profiles
· Can be used with
2″
Cover-Pools Reusable
Coping Form
1
Standard
Bullnose
All diagrams are for general information. Consult installation instructions for details.
11/16″
2-13/16″
1-1/2″ 3-1/2″ 4″
Universal Deck-Mounted
Track
11/16″
· For existing decks
· Low profile
· Installed on surface of
the deck
· Anodized aluminum
2-13/16″
SnapTopTM Track · For existing decks · Low profile · Installed on the deck
surface · Anodized aluminum · Uses gliders or wheels · Screws are concealed ·
Standard Universal track
also available · Smaller SlimTM track
available for Step-SaverTM systems
Universal track for spas and Step-Saver
Flush Track · For new or existing pools · Installed flush with deck · Vinyl-
liner, fiberglass or
concrete pools · Anodized aluminum
Recommended for indoor use only
Special Construction Applications Deck-on-Deck Pools
Create a rectangular frame around the free-form pool for an undertrack
installation with track channel.
track channel or deck straps
Extreme Cantilever
Create a freeform pool by extending the cantilever up to 24″ beyond the
channel or track.
Vanishing-Edge Pools
Create a 45° or 90° vanishing edge
45°
90°
Perimeter Overflow
Create a pool for which water height appears even with the deck. A narrow
channel collects the overflow water and allows for the glider arms.
track channel or deck straps
All exposed aluminum extrusions can be painted to match deck color.
2 All diagrams are for general information. Consult installation instructions for details.
EXCAVATION AND PLUMBING
2 Consider any special requirements for excavation and plumbing.
Recessed Mechanism–UndersideTM Track or Track Channel
1. The tracks (and rectangular pools) must be a true rectangle. The tracks
must be perpendicular to the unit mechanism and recessed housing (90°).
2. Over-dig the recessed cover box end of the pool 18″ beyond the forms. Do
not install plumbing within 14″ of the deck in the housing area.
3. The motor can be on either end of the cover box. 4. Do not locate skimmers
in the lowered pool wall. 5. All corners must be square (no radius) on the
finished tile line or the coping. 6. Place 3″ drain in floor or wall of
recessed housing.
A
Pool must be square: AB=CD AD=CB
B
no radius corners at pool wall or coping
motor side
C
motor side
36″
excavation from waterline
lowered pool wall
F
shaded area=excavation
opposite side
Track squared to box
or mechanism
E
GE = 6′
GF = 8′
FE = 10′
D
G
18″
16″
excavation from waterline
3 All diagrams are for general information. Consult installation instructions for details.
Recessed Mechanism–Universal, SnapTopTM, or Flush Track
The requirements of a recessed mechanism with a deck-mounted track are the
same as the undertrack on the previous page. Universal track may be mounted at
the pool edge. Flush track must be set back 6″ from the pool edge.
A 2′ beyond pool
Tracks must be square: AB=CD AD=CB
TRACK DIAGONALS: AD=BC
B
Do not locate track on top of a skimmer lid.
TRACK LENGTH: AC=BD
TRACK SPACE: AB=CD
Track squared to box
E
or mechanism GE = 6′
GF = 8′
FE = 10′
C
1′ minimum setback
F
D
18″
non-motor side
motor side G
16″
36″
shaded area=excavation
4 All diagrams are for general information. Consult installation instructions for details.
ELECTRICAL
3 Choose electric or hydraulic power and controlling devices.
WARNING! These are minimum recommendations only. All local and federal codes of standard safe practices must be followed. Refer to the prewiring instructions for detailed instructions and additional mounting options. TURN OFF POWER AT THE BREAKER BEFORE ATTEMPTING ANY SERVICE ON THIS EQUIPMENT.
Electric Motor w/ Toggle Switch (Standard Equipment)
¾ hp Motor with Slip Clutch
Toggle Switch
All switches must be mounted in full view of the cover operation.
Pool Cover Housing
MOTOR
Conduit to 120 VAC 15 AMP dedicated G.F.C.I.
(Hot, Neutral, Ground)
14 AWG under 50ft 12 AWG over 50ft
14 AWG under 50ft 12 AWG over 50ft Dedicated
GFCI
Conduit with three different colored wires and one ground.
(Neutral, Dir 1, Dir 2, Ground)
36″ of waterproof flex conduit with 1/2″ NPT watertight connector 14 AWG Min. Wire extended 8″ past conduit end.
electric motor
Hydraulic Power System
(Optional)
All switches/control pads must be mounted in full view of the cover operation.
POOL
Hydraulic Toggle Switch
Dedicated GFCI
Conduit to HYD pump J-box with 2 identified wires and 1 ground 14 AWG under
50ft 12 AWG over 50ft
hydraulic motor
HYD PUMP UNIT
COVER HOUSING
Conduit With (3) 12 AWG (min) Identified Wires plus one ground
HYDRAULIC MOTOR END
LARGE SWEEPING BENDS
3″ conduit
CONDUIT FOR HYDRAULIC HOSE WITH SWEEPING BENDS
two 1/2″ hoses over 80′
3″ poly or PVC pipe from housing to power unit. NO SHARP BENDS!
Hydraulic motors must be mounted above ground level.
5 All diagrams are for general information. Consult installation instructions for details.
Auto-Shutoff with Optional Accessory Board/AquaLink® ¾ hp Motor
All switches/control pads must be mounted in full view of the cover operation.
Option 1: Auto-shutoff mounted outside housing.
Option 1: Key Switch 5v
Green
Red
LED
LED
Option 2:
Conduit with (3)
CoverLink Wired Control
18 AWG Identified
Wires for Low
Voltage Key Switch
Conduit with (4) 18 AWG (min)
Identified Wires for CoverLink
OR
Wired Control
POOL
8 Bonding Wire Both Ends
COVER HOUSING
Conduit with (4) 14 AWG Wires For Power and (3) 18 Awg for Sensors
ACC Optional Accessory Board or AquaLink Conduit with (4) 18 AWG Wires
AS Install auto-shutoff away from cover housing in or by equipment room or
equipment pad
MOTOR
J-box
36″ of Waterproof Flex Conduit with 1/2″ NPT Water Tight Connector, Extend (4)
14 AWG Wires 8″ Past Conduit End
14 AWG under 50ft 12 AWG over 50ft Dedicated
GFCI
Conduit for Main Power with (3) 14 AWG Identified Wires (Hot, Neutral, Ground)
electric 3/4 hp motor
CLEAR LINE OF RECEPTION
Auto-Shutoff with Accessory Board/AquaLink® and Wireless
(Optional) — ¾ hp Motor
All control pads must be mounted in
Green
Red
LED
LED
CoverLink Wireless
Control Pad
full view of the cover operation. Install the accessory board in or by the equipment room or equipment pad,
away from the cover housing.
POOL
Receiver
ACC Optional Accessory Board or AquaLink Conduit with (4) 18 AWG Wires
Install acc board away from cover housing in or by equipment room or equipment
pad
COVER HOUSING
AS
Dedicated
14 AWG under 50ft GFCI
8 Bonding Wire (Both Sides)
Auto-shutoff Antenna
12 AWG over 50ft Conduit for Main Power with (3) 14 AWG
Identified Wires (Hot, Neutral, Ground)
36″ of Waterproof Flex Conduit with 1/2″
NPT Watertight Connector for 14 Awg
Wire Extended 8″ Past Conduit End
electric 3/4 hp motor
6 All diagrams are for general information. Consult installation instructions for details.
MECHANISM HOUSING
4 Choose a recessed mechanism (concrete or wood box) or deck-mounted
mechanism.
Recessed Concrete, Wood, or UPB Box–UndersideTM Track
conduit must be on the motor end conduit should not protrude more than 4″ into
box conduit 6″ max from top of box
bond wire
POOL
M
drain centerline 4″ max from end wall
pool beam wall
D
B
T[
O
W
bond wire
3″ drain – floor or wall can be on either end
wall cut away for clarity
Consult a certified electrician and the pre-wiring diagrams for conduit and bonding requirements.
Underside Track Box Dimensions for Save-T® 3
MOTOR M
OPPOSITE O
BEAM B
THROAT T
DEPTH D
WIDTH W
Pools under 55 ft. long x 24 ft. wide
UPB BOX Pools up to 55 ft. long
Pools over 55 ft. long x 24 ft. wide
32″
10″
8-12″
2″ min to
12-1/2″ 12-1/2″
finished beam min
min
32″
10″
8-12″
2″ min to
13″
13″
finished beam
32″
10″
8-12″
2″ min to
14½”
14½”
finished beam
Pools over 65 ft. long or 25 ft. wide and vanishing-edge pools — Call Cover- Pools 1-800-447-2838
Box Side View–Underside Track
lid
minimum 2″ clearance for tracks
7 All diagrams are for general information. Consult installation instructions for details.
Recessed Concrete, Wood, or UPB Box–Autosave OPTION 1: Conduit comes from back of box.
POOL
M
drain centerline 4″ max from end wall
pool beam wall
BT
O D
3″ drain – floor or wall can be on either end
W
Conduit comes from center of the housing
recessed box wall cut away for clarity
bond wire to bonding grid (route so that cover will not rub or catch or interfere with mechanism)
Consult a certified electrician and the pre-wiring diagrams for conduit and bonding requirements.
Underside Track Box Dimensions For AutosaveTM Up to 13′ or 200 square feet
Motor Behind
w/ Auto-Shutoff
Motor Below
w/ Auto-Shutoff
Motor M
Opposite O
9″ min 14-1/2″ min
9″ min 14-1/2″ min
9″ min 9″ min 9″ min 9″ min
Beam B
10″ min 10″ min 10″ min 10″ min
Throat T
Depth D
Width W
1″ to Finished Beam 1″ to Finished Beam 1″ to Finished Beam 1″ to Finished Beam
9″min 12-1/2″ min 9″min 12-1/2″ min 12-1/2″ min 9″min 12-1/2″ min 9″min
Side View
8-1/2″
MTR Conduit 12″
Motor Behind
MTR 8-1/2″
12″ Conduit
Motor Below
Note: To avoid interference, run the conduit from the center of the box using flex conduit with 1/2″ water tight connector.
8 All diagrams are for general information. Consult installation instructions for details.
Recessed Concrete, Wood, or UPB Box–Autosave OPTION 2: Conduit comes from side of box.
conduit must be as close to rear wall as possible for mechanism clearance.
conduit should not protrude more than 4″ into box
POOL
pool beam wall
B
M
O
D
T
3″ drain can be on either end
W
drain centerline 4″ max from end wall
recessed box wall cut away for clarity
bond wire to bonding grid (route so that cover will not rub or catch or
interfere with mechanism)
Consult a certified electrician and the pre-wiring diagrams for conduit and
bonding requirements.
Underside Track Box Dimensions For AutosaveTM Up to 13′ or 200 square feet
Motor Behind
w/ Auto-Shutoff
Motor Below
w/ Auto-Shutoff
Motor M
Opposite O
Beam B
Throat T
Depth D
Width W
9″ min 14-1/2″ min
9″ min 14-1/2″ min
9″ min 9″ min 9″ min 9″ min
10″ min 10″ min 10″ min 10″ min
1″ to Finished Beam 9″min 12-1/2″ min
1″ to Finished Beam 9″min 12-1/2″ min
1″ to Finished Beam 12-1/2″ min 1″ to Finished Beam 12-1/2″ min
9″min 9″min
Side View
8-1/2″
MTR
12″ Motor Behind
Conduit
12″ MTR 8-1/2″
Conduit
Motor Below
9 All diagrams are for general information. Consult installation instructions for details.
Recessed Concrete, Wood, or UPB Box–Universal or SnapTopTM Track
conduit must be on the motor end
conduit should not protrude more than 4″ into box
conduit 6″ max from top of box
Consult a certified electrician and the
bond wire
pre-wiring diagrams for
conduit and bonding
requirements.
M
drain centerline 4″ max from end wall 3″ drain – floor or wall can be on
either end
POOL
pool beam wall
B
O D
W
bond wire
wall cut away for clarity
Deck Mount Track Box Dimensions for Save-T® 3
MOTOR M
OPPOSITE O
BEAM B
THROAT T
DEPTH D
Pools under 55 ft. long x 24 ft. wide 32″
10″
8-12″ 2″ min to finished beam 12½” min
UPB BOX Pools up to 55 ft. long
32″
10″
8-12″ 2″ min to finished beam
13″
Pools over 55 ft. long x 24 ft. wide
32″
10″
8-12″ 2″ min to finished beam 14½”
Pools over 65 ft. long or 25 ft. wide and vanishing-edge pools — Call Cover- Pools 1-800-447-2838
WIDTH W
12½” min 13″ 14½”
Recessed Wood Box Construction
Requirements: The material used to construct the box should be: 2″ x 12″
pressure-treated lumber or redwood
Upper trim: 2″ x 4″ pressure-treated lumber or redwood
36″ 12½”
side view
12″
to
12″
24″
side view
14½”
side view
top 12½” view braces top 14½” view
Deck-Mounted Bench Construction
EverlastTM Bench Kit
Modular bench kit uses adjustableheight brackets and polymer panels to create a low-maintenance bench system.
Bench Frame
Three-piece adjustable steel brackets provide a maximum height of 20″ by 24″ wide. Surface material is not included.
16¼” to
17½”
20″ Available in 4 colors
Deck-Mounted Fiberglass Ends
roller tube
Also available with stainless-steel base.
Fiberglass ends are an economical and practical solution to cover the deck-
mounted mechanism. Available in white.
10 All diagrams are for general information. Consult installation instructions for details.
COPING AND DECK
5 Consider the requirements for coping and deck installation.
Gunite Layout–UndersideTM track
form brace
form
2″ offset in steel
16 d nails
cover box
side wall 2½” lower
top of side wall
side wall
2½” lower than side wall
bond beam
At the recessed box end, the pool wall (bond beam) must be shot 2½” (2″
finished with tile) lower than the side walls.
The top inside pool corners (above the waterline) must be square, not radius.
interior wall
Any interior wall, such as for spas, also must be gunited 2½” (2″ finished
with tile) lower than the side walls.
Coping or Deck Requirements–Underside track
3″ cantilever no radius corners 2″ cantilever sidewalls
· All corners of the coping must be square · Minimum 2″ cantilever from tile
on side walls · Minimum 3″ cantilever from tile
on end wall opposite the mechanism
motor
lowered pool wall
11 All diagrams are for general information. Consult installation instructions for details.
Coping or Deck Requirements–Underside track (cont.)
Opening for the track must be 2½” at box (2″ finished with tile), sloping to 3″ inside pool
DECKING
2″min
2″ cantilever
box minimum
12 ½” wide x 12 ½” deep
NOTE: The track must be mounted on the flat bottom of the coping. The coping measurement is NOT the track space. Coping must not extend more than ½” past the edge of the track.
POOLWALL
2″min fromtile
TRACKSPACE
Tile Beam–Underside track
The lowered pool wall is finished with a tile surface. For the lowered wall
edge, use a rounded tile on the front and back edges to minimize scraping on
the cover.
DECK
2″ min.
Opening 2″ finished with tile or other material
2″ min.
POOL
1/4″ round edge
1/4″ roun1d/4e”drgoeunifdeexdpgoesed
12 All diagrams are for general information. Consult installation instructions for details.
RECESSED BOX COVER
6 Choose lid and brackets to cover recessed box.
Brackets
18″ max. tray or stone
24″ max. tray or stone
Standard Aluminum Lid Tilted Bracket for Universal, SnaptopTM, and Flush Track
· Stepped or tilted anodized
aluminum lid available with 4″ or 6″ hinge
Standard Aluminum Lid Flat Bracket for UndersideTM Track · Standard anodized
aluminum lid available with 4″ or 6″ hinge
BezelTM lids
3/8″
Vanishing Lid Adjustable 12″ Stainless-Steel Bracket · For any tray less
than 18″ · Extensions 14½” & 17½”
available
Vanishing Lid Adjustable 18″ Stainless-Steel Bracket · Maximum bracket
spacing is two feet · For trays 18-24″ wide · Extensions 20½” & 23½”
available
1½
1½
Flush Mount Lid for vinyl liner pools with UPB Box
Flat Bezel Lid
Tilted Bezel Lid
Available in 16″ or 18″ width
Vanishing LidTM System
Stepped Bezel Lid
Available in 16″ width with 16″ or 18″ ends
NOTE: Walk-on Vanishing Lid systems require a concrete housing, or, if using a
wood housing, a concrete wall must be poured behind the box for anchoring
brackets.
Walk-On Vanishing Lid This design offers an adjustable tray support system for
any type of deck material. Stainless-steel or aluminum trays and stainless-
steel brackets provide the support base for a strong walk-on lid that can
blend with the surrounding deck.
6″ Min
Note: The deck thickness must be increased for extended trays if the leading
edge is going to fit under the tray. Contact Cover-Pools for more information.
The maximum width of any tray is 24″. The maximum length of tray is 24″.
13 All diagrams are for general information. Consult installation instructions for details.
SPECIFICATIONS
7 Review system details for Save-T® covers.
Quad-CoreTM or Pro-CoatTM Fabric
· Designed for the pool environment: UV, mildew, and pool-chemical resistant
with superior
dimensional stability · Strength: Exceeds the ASTM F1346-91 minimum
standard of 485 lbs. per 4′ radius · Construction: Fabric is attached to
webbing and
low-stretch rope (70,000+ cyclic loading fatigue life) with double-sewn
Dabond® bonded polyester thread for
durability · Additional special-order colors available · 7- year prorated
standard limited warranty · Sewn webbing in 9 optional colors · Optional
UltimateTM heat sealed webbing in 6 colors · Optional Ultimate rope (100,000+
cyclic loading fatigue
life)
Power and Controls
· 3-year limited warranty on all electrical · 3/4 hp waterproof electric motor
Optional UltimateTM High-Torque Motor
· 1 ½ hp/2000 PSI hydraulic system · Safety lockout key control · CoverLinkTM
touchpad control (wired or wireless) · Low-voltage auto-shutoff with key
switch · Water-feature shutoff · Jandy AquaLink® Interface
Safety
· Exceeds ASTM F1346-91 requirements · Full UL listing · Bonding included with
all automatic systems · Automatic water-removal cover pump included
Track Styles
· 7-year limited warranty on all aluminum extrusions · All aluminum extrusions
are 100% anodized · UndersideTM, SnapTopTM, Universal, SlimTM, or Flush
track · Safety-Lock track channel · Top-mounted track channel for concrete and
fiberglass pools · Inverted track channel for concrete or
deck-on-deck applications · Track channel system for vinyl pools · Coping
channel for vinyl pools · V-PakTM kit for vinyl pools (includes system,
fabric,
channel, box, and lid) · Reusable coping forms (3 Profiles) · 45-degree
vanishing-edge pools · 90-degree vanishing-edge pools · Corr-ResistTM non-
metallic track channel
· NOTE: Some cover manufacturers treat cover pumps and bonding as options for
their systems. A solid safety cover without a pump is NOT approved to ASTM
F1346-91 safety standards. The installation of an automatic cover system
without bonding is not a UL-listed product.
Other Options
· Painting–all extrusions can be painted to match most deck surfaces or fabric
colors
Mechanism
· Exclusive Corr-Resist end hubs with stainless steel,
designed for salt water systems · Marine-grade anodized aluminum frame and
bracket · Limited lifetime warranty · Exclusive positive-shift system ·
Exclusive Corr-Resist rope reel with stainless steel side
plates designed for quiet operation · Standard electric system comes with
either the slip
clutch or auto-shutoff
Mechanism Housing
· Standard 12″ aluminum lid with either 4″ or 6″ hinge
· BezelTM lids, 16″ and 18″ wide
· Vanishing LidTM trays, 12″24″ wide with stainless-steel
trays and stainless-steel adjustable brackets
· Fiberglass deck-mounted mechanism end housings
· UltimateTM Polymer recessed box
· EverlastTM modular bench kit (available in 4 colors)
· Bench frame assembly
14
All diagrams are for general information. Consult installation instructions for details.
COVER SIZING AND PRICING
8 Determine pricing according to the cover specifications.
Pricing based on motor mechanism being installed one foot from pool edge, motor position on left or right.
Undertrack
Deck-Mounted Track 2′
Track Space
Track Space Track Space
Pool Length
Pool Length
1′
Mechanism
1′
Mechanism
TRACK SPACE x POOL LENGTH = COVER SQUARE-FOOT PRICING
Track widths over 25′ or lengths over 65′ require factory approval (maximum
track space is 36′).
15 All diagrams are for general information. Consult installation instructions for details.
Cost Considerations
Excavation/Plumbing
q Housing excavation q 3″ drain for housing drain– drain to air
or drain to pit q 3″ conduit for hydraulic-unit housing
Electrical
q 1/2″ Conduit for mechanism power q Electric run to key switch q 15-amp GFCI
dedicated circuit for mechanism at
panel (20 AMP for hydraulic) q Electric runs over 50′ require heavy-gauge wire
q Electrical run for accessory board q 1/2″ Conduit (for low voltage wires)
required with
Auto-shutoff/CoverLink wired controls
Concrete
q Concrete, gunite or shotcrete box, minimum 6″ thick, 3500 PSI, (no rebound)
q Additional deck around housing/mechanism q Tile on lower beam, beam cover or
other
Cover/Mechanism
q Unit price based on track space x pool length including steps, plus options
q Track space 25′ 6″ or more may require a larger main mechanism tube and
larger leading edge for fabric
Track
UndersideTM track or Universal track standard q Track channel for concrete or
fiberglass pools
(2 or 3 sided) q Flush track q SnapTopTM track q Vinyl-liner pool coping 90°,
45°, 6″ radius or 24″
radius q Track channel for vinyl-liner pools q Vanishing edge 45° or 90° q
Painted track extrusions
Housing
Aluminum lid, bench frame or fiberglass ends standard q Painted lid extrusions
q Aluminum Lids: Standard, BezelTM lids, or Flush Mount q Walk-on Vanishing
LidTM trays q Bench for deck-mounted mechanism
Power/Controls
110 V motor and hard-wired 3-wire key standard q Auto-shutoff control with amp
limit q Wireless CoverLinkTM digital touchpad control q Wired CoverLink
digital touchpad control q Water-feature shutoff/accessory board q Hydraulic
pump with hydraulic hoses q Jandy AquaLink® interface & control
16 All diagrams are for general information. Consult installation instructions for details.
SAVE-T® 3 Automatic Pool Cover System
18OZ FABRIC COLORS
GLIDER STOP
WEBBING STOP BLOCK
TOGGLE SWITCH
Pro-CoatTM · brown · charcoal · gray · light blue
· navy · royal blue · tan
LOW-STRETCH ROPE · 70,000 cycle loading
fatigue life · attached with double-
· prevents glider from running past the track
· ensures cover stops in correct position
· attaches to track
· simple installation to set cover travel length
· clamp design allows easy adjustment
· premium aluminum faceplate
· silicone-sealed door
· keyed access
Quad-CoreTM · aqua · beige · black · brown · dusky blue · forest green
· gray · light blue · royal blue · slate gray · tan
sewn, Dabond® bonded polyester thread.
ULTIMATETM ROPE · 100,000 cycle loading
fatigue life
POSITIVE SHIFT SYSTEM · all stainless-steel shaft and
shifting-dog components · no shear pins or bolts · 3/8″ solid stainless-steel
COVERLINKTM CONTROL · 10-number wireless or
wired touch pad · wireless systems use
secure FM-radio technology with signal
Optional colored webbing or Heat
drive dowel
lock
Sealed Webbing
· fits in a single gang box
· wireless touchpad uses
3/4 hp WATER RESISTANT MOTOR
AA batteries
· 3/4 hp, 41 rpm, 1600 in-lbs of torque
· capacitor-start, capacitor-run · O-ring sealed and potted
wire-entry points · stainless-steel gears with sealed
permanent grease · UL Listed · Optional UltimateTM High-Torque Motor
3/4 hp, 27 rpm, 1375 in-lbs of torque
ROLLER TUBE BRAKE · stainless-steel
brake adjuster
AQUALINK® INTERFACE
BOARD · cover position controls pool
features · reduce the filter pump time · adjust salt chlorine production
levels automatically · turn off water features, lights,
and booster pump cleaners · view pool cover position anywhere with iAquaLink®
app
CORR-RESISTTM ROPE
SLIP CLUTCH · stainless-steel and aluminum
construction · long-wearing industrial-grade
friction material (not plastic) · waterproof and temperature-
proof operation · no replacement parts needed · lifetime warranty
REEL SYSTEM · EZ-Lock rope reel system
for simple cover alignment · choose between ratcheting
or locked rope reels · easy adjustment on out-of-
square pools · simple adjustment of cover
alignment · simple change-over to
locked or unlocked reels
· easy to adjust · keeps cover taut
CORR-RESIST HYBRID END
EXCLUSIVE!
CASTINGTM
MARINE-GRADE
· stainless steel and
ANODIZED ROLLER DRUM Corr-ResistTM components
· strong 17 gauge thick
· designed for mineral sanitizing
aluminum tube
systems
· 6″ & 8″ diameters available · minimizes salt corrosion
· anodized aluminum
· can be retrofitted to previous
protects against corrosion models
AUTO-SHUTOFF WITH AMP LIMITER · compact potted waterproof design · adjustable amp limiter overload safety circuit · LED indicator and diagnostic lights · optional water-feature control board (can control 12- and 24-volt motorized valves or pump motors up to 30 amps)
and oxidation
Autosave Spa Cover System
.16 hp WATER RESISTANT MOTOR · .16 hp, 35 rpm,
229 in-lbs of torque · capacitor-start, capacitor-run · O-ring sealed and
potted
wire-entry points · stainless-steel gears with sealed
permanent grease · UL Listed · Optional high-torque sprocket for
larger spas
LOW-STRETCH ROPE · 70,000 cycle loading
fatigue life · attached with double-
sewn, Dabond® bonded polyester thread.
ULTIMATETM ROPE · 100,000 cycle loading
fatigue life
GLIDER STOP · prevents glider from
running past the track · ensures cover stops in
correct position · attaches to track
POSITIVE SHIFT SYSTEM · stainless-steel shifting-dog
components · no shear pins or bolts · 1/4″ solid stainless-steel
drive dowel
18OZ FABRIC COLORS
Pro-CoatTM · brown · charcoal · gray · light blue
· navy · royal blue · tan
CORR-RESISTTM ROPE REEL SYSTEM · aluminum sides with a
polymer center
WEBBING STOP BLOCK · simple installation to set
cover travel length · clamp design allows
easy adjustment
TOGGLE SWITCH · premium aluminum
faceplate · silicone-sealed
door · keyed access
3″ PVC ROLLER DRUM · Optional 4″ diameter
aluminum roller drum for larger spas (added strength
and rigidity)
COVERLINKTM CONTROL · 10-number wireless or
wired touch pad · wireless systems use
secure FM-radio technology with signal lock · fits in a single gang box ·
wireless touchpad uses AA batteries
CORR-RESISTTM POLYMER END HUB · designed for mineral sanitizing
systems
· minimizes salt corrosion
AQUALINK® INTERFACE
BOARD · cover position controls pool
features · reduce the filter pump time · adjust salt chlorine production
levels automatically · turn off water features, lights,
and booster pump cleaners · view pool cover position anywhere with iAquaLink®
app
Quad-CoreTM · aqua · beige · black · brown · dusky blue · forest green
· gray · light blue · royal blue · slate gray · tan
Optional colored webbing or Heat Sealed Webbing
ROLLER TUBE BRAKE · stainless-steel brake
adjuster · easy to adjust · keeps cover taut
AUTO-SHUTOFF WITH AMP LIMITER · compact potted waterproof design · adjustable
amp limiter overload safety circuit · LED indicator and diagnostic lights ·
optional water-feature control board (can control
12- and 24-volt motorized valves or pump motors up to 30 amps)
NOTES
NOTES
NOTES
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>