Godox TP2R Knowled RGBWW Pixel Tube Light Instruction Manual

: June 11, 2024
: Godox

Godox TP2R Knowled RGBWW Pixel Tube Light

Name of Parts

Light Body

CRMX Indicator
Bluetooth Indicator
Battery Level Indicator
Display
Power Switch Button
MOD/MENU Bullon
FN Button
– Button
+ Button
DMX Port
DC Input Port
3/8″ Screw Hole

Display

When icon is on the display, it means DC power supply.
When icon is on the display, it means lithium battery power supply.

What’s Inside (TP2R/TP4R)

Note: Due to continuous updates and upgrades of the products, there may be differences between the actual products and the pictures. Therefore, the pictures are for reference only, products to prevail in kind.

Separately Sold Accessories

Power Box TP-P600, Multi-tube Light Connector (Two Joints) TP-M2, Two-light Bracket Kit TP-B2, Four-light Bracket Kit TP-B4, Eight-light Bracket Kit TP-B8, Softbox TP-S2, Air Soft Tube TP-S2A, DMX Connector Cable DMX-C1, Floor Stand TP-FS60

Battery

This product has built-in lithium battery. The inner circuit is against overcharge, over-discharge, over current, and short circuit.
Please use the standard adapter for charging.

Indicators Description

Highlight Mode

The light is in highlight mode and max. power when powered by DC power source.

Connect to DMX Controller

Wireless DMX Connection

Wired DMX Connection

Operation Instruction

Power Switch

Long press the power switch button for 2s to turn on or off the device.

Note: The device will be turned on automatically in DC power supply if the quick start function is turned on (available in menu setting).

Mode Settings

Short press the MOD/MENU button to switch among CCT mode, HSI mode, RGB mode, GEL mode and FX mode.

CCT Mode

Short press the FN button in CCT mode to adjust DIM/CCT/GM, press + button to increase value while press – button to decrease value.

DIM: 0%-100%
CCT: 2000K-10000K
GM: -50-+50

HSI Mode

Short press the FN button in HSI mode to adjust H (HUE)/S (saturation)/I (intensity), press + button to increase value while press – button to decrease value.

H (HUE): 0°-360°
S (saturation): 0%-100%
I (intensity): 0%-100%

RGB Mode

Short press the FN button in RGB mode to adjust R (red)/G (green)/B (blue)/W (white)/| (intensity), press + button to increase value while press – button to decrease value.

R (red): 0-255
G (green): 0-255
B (blue): 0-255
W (white): 0-255
I (intensity): 0%-100%

GEL Mode

Short press the FN button in GEL mode to adjust DIM/GEL/Num/CCT, press + button to increase value while press button to decrease value.

DIM: 0%-100%
GEL: L-GEL, R-GEL
L-GEL Num: 30
R-GEL Num: 30
CCT: 3200K, 5600K

FX Mode

Short press the +/- button in FX mode to select the desired effect, then short press the FN button to select an effect setting, press +/- button to adjust the setting.Short press the FN button for 2s can return to the previous option. There are 17 effects for choice: RB fade, RGB flow, RGB chase, RGB cycle, party, flash, lightning, cloudy, broken bulb, TV, candle, fire, firework, explosion, welding, cop car, SOS.

RGB fade

RGB fade effect supports adjustable DIM, speed, color and direction.

DIM: 0%-100%
Speed: 1-100
Color Width: 1-8
Color Num: 1_8
- Available colors of C1 to C8: 3200K, 5600K, Red, Orange, Yellow, Green, Cyan, Blue, Purple, Magenta
DIR: L (left/R (right)

_ Note: _Short press the MOD/MENU button in secondary option can return to the previous menu.

RGB Flow

RGB flow effect supports adjustable DIM speed, color and direction.

DIM: 0%-100%
Speed: 1-100
Color Width: 1-8
Color Num: 2-8
- Available colors of C1 to C8: 3200K, 5600K, Red, Orange, Yellow, Green, Cyan, Blue, Purple, Magenta
DIR: L (left)/R (right)

Note: Short press the MOD/MENU button in secondary option can return to the previous menu.

RGB Chase

RGB chase effect supports adjustable DIM, speed, color and direction.
DIM: 0%-100%
Speed: 1-100
Color Width: 1-8
- Color Num: 2-8 Available colors of C1 to C8: 3200K, 5600K, Red, Orange, Yellow, Green, Cyan, Blue, Purple, Magenta
DIR: L (left)/R (right)

Note: Short press the MOD/MENU button in secondary option can return to the previous menu.

RGB Cycle

DIM: 0%-100%
Speed: 1-100
SAT (saturation): 0%-100%

Flash

Trig: Auto, Manual
DIM: 0%-100%
Speed: 1-100 (only adjustable in auto mode)

Note: Short press + button once to trigger flash once in manual mode.

Lightning

Trig: Auto, Manual
DIM: 0%-100%
Blinks: Rnd/1-10
Freq: Rnd/2-20 (only adjustable in auto mode)

Note: Short press + button once to trigger lightning once in manual mode.

Cloudy

DIM: 0%-100%
DIM Ratio: 30%-90%
Speed: Rnd/1-100

Broken Bulb

Color: CCT, HSI
CCT: 2000K-10000K (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-100%
Speed: Rnd/1-100

TV

Color: CCT, HSI
DIM: 0%-100%
Speed: 1-100

Candle

DIM: 0%-100%
Speed: 1-100

Fire

DIM: 0%-100%
Speed: 1-100

Firework

DIM: 0%-100%
Embers: 1-100
Speed: 1-100

Explosion

Trig: Auto, Manual
Color: CCT, HSI
CCT: 2000K-10000K (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-100%
Embers: 1-100
Speed: 1-100 (only adjustable in auto mode)

Note: Short press + button once to trigger explosion once in manual mode.

Welding

Color: CCT, HSI
CCT: 2000K-10000K (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-100%
Speed: 1-100

Cop Car

Color: CCT, HSI
CCT: 2000K-10000K (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-100%
Speed: 1-100

SOS

Color: CCT, HSI
CCT: 2000K-10000K (only adjustable in CCT mode)
HUE: 0°-360° (only adjustable in HSI mode)
DIM: 0%-100%

Setting

Long press the MOD/MENU button to enter Setting, short press the FN button to select DMX/CRMX/ Ordering/Bluetooth/Dimming Curve/Quick Start/Rotate Screen/Preset/Battery/Language/Factory Reset/Version (short press FN button twice can return to previous option), short press the + button to enter the desired setting, after which short press the MOD/MENU button can return to previous setting.

DMX

Short press the FN button to select ADD/MOD/Pixels/Loss/RDM in DMX settings interface, then short press -/+ button to adjust the settings.

RDM on: The luminaire ADD and DMX mode are operational via controller.

_ Note: _Please refer to the ” TP2R DMX Practical Table” and ” TP4R DMX Practical Table” to control the device by DMX, the electronic versions of which can be downloaded from the official website https://www.godox.com.

CRMX

Short press the – button can turn off CRMX while short press the + button can turn on CRMX. When the CRMX is turned on, short press the FN button to MOD, then short press the -/+ button to select TX/RX mode.

RX mode: CRMX indicator will be constant on green when linked.
TX mode: Short press the FN button to select Link/Unlink/Power. Short press the + button to link or unlink. Short press the -/+ button to adjust power. CRMX indicator will be constant on magenta when transmitting DMX data, and blink magenta when unlinked.

Ordering

Short press the FN button to select Pixels/ADD/Final, short press the -/+ button can adjust the desired setting. Ordering function is suitable for combining multi luminaires to realize effects transit from the main luminaire (the one set as TX mode) to last luminaire in RGB fade, RGB flow and RGB chase modes.

Ordering Illustration

The CRMX mode of main luminaire should be set as transmitter, while the CRMX mode of other luminaires should be set as receiver.

_ Note: _Only the last luminaire needs to set the final ADD.

When the nivel is

The ADD calculation formula: M (M means the NO. of luminaire)
The final ADD calculation formula: N (N means numbers of fixtures used in practical.

When the pixel is 2

The ADD calculation formula: 2M-1 (M means the NO. of luminaire)
The final ADD calculation formula: 2N (N means numbers of fixtures used in practical.)

When the pixel is 4

The ADD calculation formula: 4M-3 (M means the NO. of luminaire)
The final ADD calculation formula: 4N (N means numbers of fixtures used in practical.)

When the pixel is 8

The ADD calculation formula: 8M-7 (M means the NO. of luminaire)
The final ADD calculation formula: 8N (N means numbers of fixtures used in practical.)

When the pixel is 16

The ADD calculation formula: 16M-15 (M means the NO. of luminaire)
The final ADD calculation formula: 16N (N means numbers of fixtures used in practical.)

When the pixel is 32

Bluetooth

Short press FN button to select BT (Bluetooth switch)/Reset. BT (Bluetooth switch): Short press the – button to turn off the Bluetooth and the Bluetooth indicator will be off. Short press the + button to turn on the Bluetooth and the Bluetooth indicator will be constant on blue.

Reset: Short press the+ button to reset the Bluetooth, and the Bluetooth indicator will blink when resetting and stop blinking after successfully reset.

Bluetooth MAC code is on the lower right corner of Bluetooth interface for matching with other luminaires, after which short press the MOD/MENU button can return to the previous setting.

Note

The APP can be used directly on the firstly installed device (smartphone or iPad). When change to other mobile device (smartphone or iPad), the light shall be reset before the normal connection of APP. The APP should be upgraded to version 3.0 or above.

Note

CRMX wireless and Bluetooth both use 2.4G frequency, so it’s recommended not to turn on at the same time to avoid disturbance.
Please avoid or turn off the 2.4G transmitting signal nearby for the sake of stability when using Bluetooth.
Dimming Curve: Short press the FN button to select Linear/S-curve/Exp/Log in dimming curve interface.
Quick Start: Short press the FN button to turn on/off the quick start function.

Rotate Screen

Short press the FN button to select upward/downward in rotate screen interface.
Press the FN and – button at the same time can rotate screen quickly.

Preset

Short press the FN button to select from P1 to P20 in preset interface. Short press the + button to enter the desired preset, then short press the FN button to select Apply/Save/Cancel, and short press the + button to confirm. If you select apply, it will go to the preset effect interface.

Note: Short press the FN button twice can return to the previous setting. There will be no “Apply option if no effect is set in the Preset.

Battery

The battery level and estimated working time is displayed in the battery interface.

Language

Short press the FN button to choose Chinese or English in the language interface, after which short press the MOD/MENU button can return to the previous setting.

Factory Reset

Short press the FN button to choose No or Yes in the factory reset interface. If you choose “No” , short press the + button or MOD/MENU button can return to the previous setting. If you choose “Yes” , short press the + button can restore to factory setting, after which it will turn to 100% brightness and return to the previous setting.

Version

The firmware version and upgrade information are displayed on the Version interface.
For Bluetooth upgrade, please refer to the detailed tutorial of “Godox Light” APP.

Upgrade via USB disk

Download the new firmware to the USB disk from official website https://www.godox.com/firmware-continuous-light).
Turn off the device. Insert the USB disk with new firmware into the Type-C USB port.
Turn on the device, and it will automatically enter the upgrading interface.
It will return to main interface after completion.

Notes: New firmware must be downloaded from the official website, and keep onlv one BIN file in the root directory of the USB disk.

Setting Instruction

Illuminance Data

TP2R

TP4R

Note: All the above tests are based on the condition of 100% brightness. The results are average values instead of absolute values.

Technical Data

Specifications and data may subject to changes without notice.

Operating frequency: 2402MHz – 2480MHz(2.4G)/2402MHz – 2480MHz(BT)
Maximum EIRP Power: 5dBm/5dBm

Declaration of Conformity

GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states. For more information of DoC, Please click this web link: https://www.godox.com/DOC/Godox_TP2R_TP4R_DOC.pdf

The device complies with RF specifications when the device used at 0mm from your body.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

_ Note: _This form shall be sealed by the seller.

Applicable Products

The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases:

The product or accessory has expired its warranty period;
Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;
Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
The original identifying information of product or accessory is modified, alternated, or removed;
No valid warranty card;
Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
Breakage or damage caused by force majeure or accident;
Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Godox After-sale Service Call 0755-29609320-8062

WeChat Official Account

GODOX Photo Equipment Co., Ltd.

Add.: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’ an District, Shenzhen 518103, China
Tel: +86-755-29609320(8062)
Fax: +86-755-25723423
E-mail : godox@godox.com
www.godox.com
Made in China
705-TP2R00-00