BLUETTI EP600 Energy Storage System Instruction Manual

IOT Controller instruction manual
IOT Controller **S010A
BLUETTI
SHENZHEN POWEROAK NEWENER CO., LTD.
CMIIT ID:XXXXXXXXXXX**

Communication methods

The EP600 energy storage system is connected to the IOT controller, and the inverter information can be seen on the mobile APP through Bluetooth or WiFi. And remotely control the working mode of the inverter.
The working information of the system (power generation, alarm, and working status) can be uploaded to the server through WiFi network. Users can use the APP to view and control the device according to their needs, which requires registering an account and binding the device by scanning the QR code of EP600.

The IOT controller contain the following communication methods:

Overview

1. Menu Button.
   To factory reset the controller, press and hold this button till all LED indicators flash.

2. WiFi Indicator.
   Flash till the controller connected to WiFi.

3. Bluetooth Indicator.
   Flash till the controller connected to Bluetooth.

4. Reset Button.

Installation

Danger
Avoid cables and pipes before drilling into the wall.
a. Drill 2 pilot holes in the wall. Please refer to the drill position and hole size shown in fig. 6.14.1 and fig. 6.14.2. The depth of hole is 26mm.
b. Hammer the expansion anchor in until it’s flush with the wall. See fig. 4.14.3.
c. Fix the mounting bracket onto the wall and use the Phillips screwdriver to fasten 2 self-tapping screws into the expansion anchors. See fig. 4.14.4.
d. Align the controller’s buckle over the U-slot and push the controller downwards until it snaps in place. See fig. 4.14.5 and fig. 4.14.6.

Safety Instructions

• The IoT controller is ONLY applicable to BLUETTI products only.

• Do not keep the controller near heat sources or in high temperatures.

• Do not store the controller with flammable liquids, gases, or explosive materials.

• The inspection, testing, and maintenance should be performed by qualified personnel.
  Warning

• Do not block or cover the openings of the controller. Keep it out of the reach of children.

• Use dry powder fire extinguisher in case of fire.

Connection and Operations

a. Plug the communication cable into EP600 Signal Port 1.
b. Turn on EP600, and the IoT controller starts up automatically.
c. Configure the controller in BLUETTI app.
d. Please find “bluetti” in the app store (Apple device users) or Google play (Android device users) and download the “bluetti” app application, through which you can remotely control the power system. (see 8.2 download and install bluetti app for details).
e. The IOT controller can be remotely controlled through Bluetooth or WiFi. If you need to remotely access the device, please start the downloaded “bluetti” application, click the “login” icon and “register”, and then fill in your bluetti account and related information to complete the registration. (see 8.3 registering bluetti account for details).

• BLUETTI will send the verification code to your registered email account, and fill in the verification code to activate your BLUETTI account.

Firmware Upgrade

Upgrade via USB Drive
EP600 inverter supports firmware upgrades via a USB drive to maximize its performance and avoid failures caused by firmware errors.
a. Insert the USB drive into a USB port on your computer.
b. Download the upgrade file*, unzip and store it on the USB drive.
c. Insert the driver into the USB port on EP600.
d. Power on EP600.
e. The firmware upgrade starts automatically once the upgrade files are detected.
f. The buzzer beeps once after the firmware is updated successfully. Please unplug the USB drive, or EP600 will report a USB Format Error.
g. Pair EP600 with BLUETTI app, then you can check the firmware version on the phone.
If any of the following occurs, please try the solutions provided. If the symptom persists for 5 times ）, contact the BLUETTI support team, and we’ll get back to you in 48 business hours.

• Please contact BLUETTI customer service.

than 32G in size.
2. Check if the upgrade files exist or expire. Please download the latest upgrade files.
Firmware version not
updating or abnormal.| Please download the latest upgrade files. If the symptom persists, contact
the BLUETTI support team.

Fig. 6.11

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radio Frequency Exposure Statement:
This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

References

• BLUETTI EU: Portable Power Station, Solar Generator Kit

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>