Panasonic PV55H8950 Air Purifier Instruction Manual

Panasonic PV55H8950 Air Purifier Instruction Manual

SAFETY PRECAUTIONS

• Disconnect power supply before maintenance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for the safety. Children should be supervised to ensure that they do not play with the product.
• The following symbols differentiate the levels of danger or injury that may result if the product is not used correctly as instructed

WARNING

Those things shown in this column indicate that there is possibility of causing death or severe injury.

CAUTION

Those things shown in this column indicate that there is possibility of causing minor injury or damage to properties .

The following symbols are used to indicate the type of instructions that need to be followed. (The symbols given below are examples)

This symbol indicates an action that must not be performed.

WARNING

• Do not pull the power cord when carrying or storing the product
• Do not damage the power cord or power plug.
• Do not cut, modify, excessive distort, twist, squeeze the power cord, and do not place it near heat sources, place heavy weight on it, etc.
• Do not let the product get wet.
• Do not use power other than the rated voltage .
• Do not touch the power plug with wet hands

WARNING

• Do not insert your fingers, metallic objects or others into the air inlet, air outlet or gaps
• Clean the power plug regularly.
• Disconnect the power plug and wipe it with dry cloth.
• When the product will not be used for a long period, disconnect the power plug.
• Insert the power plug completely.
• Do not use damaged power plug or loosen power socket.
• Do not disassemble or modify the product.
• In case of any abnormality or malfunction, stop using the product immediately and disconnect the power plug.
  • The product stops operating when moving the power cord
  • If any switches do not work.
  • If the circuit breaker is tripped or when fuse blows.
  • If the power cord or power plug becomes abnormally hot.
  • If you notice a burning smell or an abnormal sound or vibration
  • If there is any other abnormalities or malfunction.

CAUTION

Do not place the product in the following places

• Incline and unstable place.
• Where the temperature or humidity is extremely high, or watery area, such as bathroom.
• Where oil fume is emitted, such as in kitchens
• Where oil or inflammable gas is present and may be leaked
• Where the air outlet faces animals or plants directly

Do not place the product near combustible materials such as lighted cigarette, incense, etc.

• Do not clean the product with gasoline or other volatile mixture solvents, and avoid contacting with spray insecticides
• Do not operate this product in places where indoor fumigation type insecticides are being used.
• Do not sit on or lean against this product
• When carrying the product, please hold the left and right handles, but not the louver or front panel.

SETTING AND OPERATING REQUIREMENTS

**Area that can enhance the effectiveness!

**

• Way to against PM2.5 and indoor dust, etc.
• Way to circulate air more effectively.
• If the product is used in the same place for a long period.
• Do not use the same power socket with TV, radio, etc.
• Do not place obstacles on the product air inlet and outlet.
• Do not place any object on the product.
• Do not set the product in the following places.
  • Where the product will be exposed directly to sunlight, outlet air of air conditioner or heat, etc.
  • Near equipment such as TV and radio.

PRODUCT FEATURES

“House Dust Catcher” and “nanoe® X” give you clean and fresh air.

• House Dust Catcher completely cleaning dust from the air near the floor
• Equipped with nanoe® X technology
• Low power consumption in the Econavi mode

About nanoe® X

1. High moisture content (the moisture content is 1,000 times the moisture content of ordinary anions)
2. High moisture content (the moisture content is 1,000 times the moisture content of ordinary anions)
3. High stability (6 times more stable than a common ion, covering a distance of 10 mor above)
4. More hydroxyl radicals (up to 4,800 billion of radicals are generated per second).
5. Weak acidity (with weak acidity features close to that of hair and skin).

MAIN PARTS IDENTIFICATION

• Filter replacement indicator
• nanoe® nanoe® X indicator The indicator lights on indicates nanoe® X is being generated. nanoe® X will be generated in all operation modes except you switch off it. ( P.15)
• PM2.5 pollution indicator
• Light sensor

SETUP

Before startup

Fill in the label with the first date of use.

Remove the deodorizing filter from the poly bag

Install the filters (2 types) and front panel

1. Install deodorizing filter. (There is no distinction between inside and outside, upper and lower)
   

2. Install HEPA composite filter. (There is distinction between inside and outside, no distinction between upper and lower)
   

3. Toggle the filter hook downward, and secure filters.
   

4. Install front panel.
   

Connect the power plug.

When inserting the power plug, as the odor sensor uses the degree of cleanliness at this time as the standard, we recommend that you plug it in when the air is fresh (when there is no cigarette smoke). (The standard of the odor sensor automatically updates itself according to the degree of the indoor cleanliness.)

OPERATION

Power Off/On

Turn on or off the product. Press the button to operate. The product operates in auto air volume mode when it is used for the first time, then operates in the last mode when it was stopped.

Air volume

Select appropriate air volume for purifying air. The indicator will be changed sequentially as figure below. Automatically adjust the air volume according to the air pollution detected by sensor, and use appropriate air volume to purify air

Econavi

Smart power-saving mode. Press the button will operate in Econavi mode. Econavi is a smart power-saving operation combined by the “patrol mode” and “learning mode”, and it adjusts the air volume automatically. (P.16)

PM2.5

Remove PM2.5 quickly. When indicator is on, you can press the button to remove PM2.5 quickly, until the indicator lights off. (At this moment the PM2.5 mode will stop, then product will switch to the previous mode and continue.) But, If you press the button when indicator is off, the PM2.5 mode only will operate in 1 min, then product will switch to the previous mode and continue.

Timer

Timer operation. The indicator will be changed sequentially as figure below.

Child lock

To prevent child from wrong operating. Long press the button for 3 seconds, then the child lock is set. With this setting, other buttons are disabled when you press them, with sound “BI-BI-”

MAINTENANCE

Notice

• For installation and removal methods of front panel and filters, please read P.9~10.
• When cleaning, do not leave the removed parts unattended
• Do not operate the product when the HEPA composite filter is removed. (Dust will be inhaled into product inner parts, and causes the product breakdown. The HEPA composite filter cannot function while it is removed.)
• Do not operate the product when the deodorizing filter is removed. (The deodorizing filter cannot function while it is removed.)
• When using chemically treated cloth, be sure to follow the instructions carefully.

WARNING

Make sure to disconnect the power plug before cleaning the product.

• Do not use the detergents shown below.

Cleaning method

Deodorizing filter

• When there is dust around the deodorizing filter, remove the dust with a vacuum cleaner, etc
• Do not wash the filter with water.

Dirt sensor < about once every 3 months >

Wipe the dirt off the lens with a dry cotton swab

1. Remove the external cover of dirt sensor as shown below.
2. Wipe the lens with a dry cotton swab as shown below

HEPA composite filter < about once every 2 weeks >

1. After replacement, please connect power plug, then press and buttons at the same time for about 3 seconds until the filter replacement indicator turns off, then the reset is completed
2. Fill in installation date on the label in filter case, then stick it on product to cover the old date. (P.9)

Notice

• The filter which needs to exchange cannot be used again even it is cleaned, please dispose it as non-flammable garbage
• If the product is used in a room (especially hotel) with strong odor such as aromatic smell, cigarette smoke or barbecue smell, these odors may adhere to the filter. When the adsorption capacity of filter reaches saturation, odor will also be blown out again with the wind because of excess adsorption. When there is above situation, please clean the HEPA composite filter. If the situation persists, please replace the HEPA composite filter and deodorizing filter, even if the filter replacement indicator is off. In addition, if often used in a room with strong odor, please open the windows to ventilate the room regularly.

When idle for a long time

1. Disconnect power after turning off the product. (The product still consumes power even at rest.)
2. Maintain the product as usual.
3. Put the product into poly bag and carton, and keep it in a dry place. (If you overturn it or keep it flat, product malfunctions may occur.)

FURTHER INFORMATION

About nanoe® X

• nanoe® X can be switched off. nanoe
• Conditions for nanoe® X generation
• When nanoe® X is generated, small amount of ozone will be released. However, the quantity will be far less than the level in natural environment such as forest, and not be harmful to human beings.

About HEPA composite filter

• Super Allergy-buster: inhibits the activity of allergic substances (pollen, dead mites and feces).
• The HEPA composite filter might emit unique and harmless smell of “Green Tea Catechin”, ”Bio-sterilization” and “Super Allergy-buster”.
• Removes ≥99.97% of 0.3 µm particles. it’s dust removing performance of filter itself, the effect in the entire room is not same.

About Econavi

Econavi mode refers to the automatic operation combined by the “patrol mode” in which the product detects the dirt in the air in the room every hour and the “learning mode” in which the product can forecast the dirt generation by mastering the generation time of dirt every day. Automatically stops operating when the clean air is detected, meanwhile it also operates in advance to eliminate the dirt effectively before spreading, thus reducing the operation time and saving power.

**Patrol mode

**

The product will stop operating automatically after the air is cleaned. After the operation is paused for 50 min,the product will operate for 10 min with air volume set to “Med” in the patrol mode. While the operation is paused in the patrol mode, the product will operate with the suitable air volume corresponding to the dirtiness detected.

Learning mode

The product records the time and dirtiness of air during operation, and takes the preventive operation 5 min before the recorded dirt is generated in the next day. (Although the records are updated every day, the previous records will be lost once the power plug is disconnected.)

About odor sensor/dirt sensor

The sensor can detect the pollution of the air, and show the pollution level by indicator. The product can optimize the air volume automatically in auto operation according to the air quality

• The sensor’s operation may vary depending on the indoor airflow condition if a heater is placed near the product in a room.
• The sensor is not designed to detect bacteria and viruses.
• The sensitivity of the sensor can be adjusted. (The default setting is “medium sensitivity” .)

Red

| Upward|
House dust is detected __ Odor/PM2.5/smog and house dust are detected| Front|
Switch direction|

About sleep mode auto operation

Detects the indoor brightness by the light sensor, and automatically adjusts the brightness of indicators and the air volume. When sleeping, the room becomes dark, the indicators will be dimmed or light off and the air volume becomes low

FAQ

Why is a “jee” sound from the emission outlet?

There is a slight sound when nanoe® X is being generated. Depends on the environment and operation mode, the sound may be a bit loud or inaudible but it is not abnormal.

Why does the clean sign turn off during operation?

The product detects the indoor brightness, and adjusts the brightness of the clean sign automatically with the “Sleep Mode Auto Operation” function. (P.18)

Why does the clean sign remain unchanged?

Such problems are easy to occur when the sensitivity of the sensor is low. You can adjust the sensor with a specified sensitivity.

How to turn off the clean sign?

• Please press and buttons at the same time for about 3 seconds during operation.
• Please press the buttons for about 3 seconds again to relight clean sign.

TROUBLESHOOTING

If a problem is encountered, please investigate it by going through the following items. If the problem still persists, please disconnect the power plug and contact the dealer for repair

subject to steam in the bathroom or vapor emitting from sprayers.
even when the operation
continues
 Automatic operation cannot  be  stopped| When the setting of air volume is “Auto”, the product will still operate with low air volume even if the air in the room is clean.
 The clean sign remains| Is the product placed in area where polluted air is difficult to be cleared or the room size is too large for the product?(P.5, back cover)
blue even when the air is
dirty
 Polluted air is difficult| Is the HEPA composite filter dirty? (P.14)Please clean it. If the situation persists, replace the filter with a new one.H
to be remove
 The air volume is small

The odor from the

| Is the body, front panel or filter dirty? (P.14)If the problem persists after the filter is cleaned, please replace it with a new one. (The harmful carbon monoxide generated by cigarette cannot be removed))Has the product ever been used in a room with strong odor?If the product is used in a room with strong odor such as aromatic smell, cigarette smoke or barbecue smell, the filter replacement period may be shortened.If you use the product in such environments, it is recommended to open the air ventilation system or open the windows to ventilate the room at the same time. If there is still strong odor to be blown out after the maintenance , please replace the HEPA composite filter and deodorizing filter, even if the filter replacement indicator does not light on.
product is unpleasant
 There is sound| After pressing                 , you may hear some sound around the louver. This is normal.

SPECIFICATIONS

OPTIONAL ACCESSORIES

• Replacement HEPA composite filter

• Replacement deodorizing filter

Please contact dealer

All the air volume indicators are blinking Product may be out of order. Please disconnect the power and contact the dealer for repair.

Panasonic Corporation

Web Site: http://www.panasonic.com

References

• Panasonic Australia | Air Con | Cameras | Home Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>