tp-link T310 Smart Temperature and Humidity Sensor User Guide
- June 11, 2024
- tp-link
Table of Contents
Quick Start Guide
Smart Temperature and
Humidity Sensor
T310 Smart Temperature and Humidity Sensor
Meet Your Temperature and Humidity Sensor
Measure the temperature and humidity of the environment and send you instant
notifications when the environment changes. It is suitable for green houses,
bedrooms, nursery, incubators, and wine cellars.
Before You Start
A Tapo Hub is required. Make sure your Tapo Hub is successfully added via
the Tapo app.
https://www.tapo.com/app
/download-app/
Power Up Your Sensor
Remove the battery insulation tab to power up your sensor. The LED should
blink.
Note: If the LED is not blinking, use a pin to press the Reset button for
5 seconds to reset your sensor and enter pairing mode.
Set Up Your Sensor
Open the Tapo app and tap the + button.
Select Sensors and then your model.
Follow the app instructions to complete setup.
Test Your Sensor
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub should make a voice prompt. Option
2
Blow on the sensor detector. The temperature and humidity displayed on the
Tapo app should change.
Place Your Sensor
(The installation height should not be higher than 2 meters.)
Option 1: Hang with the Lanyard
Option 2: Use Adhesive Magnets
a. Stick the included adhesive magnets to the back panel.
b. Magnetically attach the sensor to metallic surfaces.
Option 3: Use 3M Adhesives
a. Stick the included 3M adhesives to the back panel. b. Stick the sensor to
your preferred location.
How to replace the battery
- Use a pin to press and remove the cover.
- Replace the battery with a fresh cell (battery model: CR2450).
- Put the cover back.
Need some help?
Visit www.tapo.com/support/
for technical support, user guides, FAQs, warranty & more
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that
may result in an explosion or the leakage of flammable liquid or gas.
CAUTION: Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
CAUTION!
Risk of explosion if the battery is replaced by an incorrect type.
Operating Temperature: 20℃ (-4℉ ) ~ 60℃ (140℉ )
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at
https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations
2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)
©2023 TP-Link
*Images may differ from actual products.
7106510139 REV1.1.0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>