EZ TATTOO P2 Epic D1 Wireless Battery Tattoo Pen Machine User Manual
- June 11, 2024
- EZ TATTOO
Table of Contents
EZ TATTOO P2 Epic D1 Wireless Battery Tattoo Pen Machine
Product Information
The product is a tattoo machine with an external rotor brushless motor and a stroke length of 3.5mm. It is made of aircraft aluminum and operates on 5-12V DC voltage with a switch frequency of 60-150 Hz. The needle protrusion weight is 8.82oz (250g) with the power pack and has dimensions of 34 x 149 mm. The machine comes with a 5000mAh lithium battery, a plug P2 epic X1 user guide, and a Type-C charging cable.
Product Usage Instructions
- Before using the product, read and understand the user manual to reduce the risk of injury.
- Charge the machine using the included Type-C charging cable. The recharging time is 1000 minutes, and the working time is 5 hours.
- Insert the battery into the machine.
- To turn on the machine, press the power button located on the machine’s grip.
- Adjust the needle protrusion weight to your desired level using the adjustment knob located on the machine’s grip.
- Attach the needle to the machine’s needle holder.
- Start tattooing by moving the needle over the skin in the desired pattern.
- After use, turn off the machine and remove the needle from the needle holder.
- Clean and sterilize the needle before reusing it.
OVERVIEW
- Ø: 34mm
- L: 149mm
- INCLUDE
- PLUG
- P2 EPIC X1
- USER GUIDE
- BATTERY TYPE-C CHARGING
SPECIFICATIONS
Motor External Rotor Brushless Motor Material Aircraft Aluminum
- Stroke Length: 3.5mm Operating Voltage 5 – 12V DC
- Rpm 9000rpm: ± 10% Switch Frequency 60 – 150 Hz
- Needle: Protrusion 0 – 4.5 mm Dimensions(Ø X L) 34 x 149 mm
- Weight: 8.82oz (250g) with power pack
BASIC OPERATION
Power ON/ OFF
- Press and Hold the button for two seconds to turn P2 EPIC ON.
- Press and Hold the button for two seconds to turn P2 EPIC OFF.
Power START/ STOP
- Clik button to turn your machine START or STOP
Adjusting Voltage
- Press for to adiust in 0.1V increments.
- Press and Hold or to quickly adjust the voltage in 0.1V increments.
Start/ Stop Built-in Timer
Press button to activate your machine ON, the timing mode start.
Note: timer mode records in minutes, the maximum recording time is 999 minutes. the time is counted only when the machine is running. The timer will reset the count when the P2 EPIC is being restarted.
Push Mode
Press the’ button, Screen LOGO solid, the machine ACTIVE the strong start mode.
Press! button, Screen LOGO flashes, the machine push mode OFF.
Note: In push mode the initial voltage output is 12V lasts for 1 second and then returns to normal voltage after.
Display
Voltage, Capacity and Timer display alternately every 5 seconds under the machine working condition.
SUPER LONG RANGE
- Battery Capacity
- Recharging Time
- Working Time
BATTERY PROTECTION
NOTICE: To reduce the risk of injury, the user must read and understand the User manual before using this product, Save these instructions for future reference. -We recommended that use the included charging cable.
The battery circuitry protects the battery pack from extreme temperature, overdischarge, and over-charge. To protect the battery from damage and prolong its life, The battery pack circuitry will turn off the battery pack if it becomes overloaded or if the temperature becomes too high during use. This may happen in extremely high torque, binding, and stalling situations. The battery pack will shut down for 10s when its operating temperature exceeds 158°F (70°C), and will begin normal operation when it returns to 152°F (67°C).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>