SONY DSX-B700 FM or AM Bluetooth Car Audio Instruction Manual

June 4, 2024
Sony

SONY DSX-B700 FM or AM Bluetooth Car Audio Instruction Manual

Warning

For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use.
For details, see “Connection/Installation”
(page 11).

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.
The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and Switzerland.

WARNING: Do not ingest battery, Chemical Burn Hazard.
The remote commander contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Note on the lithium battery
Do not expose the battery to excessive heat such as direct sunlight, fire or the like.

Warning if your car’s ignition has no ACC position
Be sure to set the AUTO OFF function. The unit will shut off completely and automatically in the set time after the unit is turned off and the clock is displayed (i.e. press and hold OFF for 1 second), which prevents battery drain. If you do not set the AUTO OFF function, press and hold OFF until the display disappears each time you turn the ignition off.

Disclaimer regarding services offered by third parties
Services offered by third parties may be changed, suspended, or terminated without prior notice. Sony does not bear any responsibility in these sorts of situations.

Important notice

Caution
IN NO EVENT SHALL SONY BE LIABLE FOR ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR OTHER DAMAGES INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWNTIME, AND PURCHASER’S TIME RELATED TO OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS HARDWARE AND/OR ITS SOFTWARE.
Dear customer, this product includes a radio transmitter.
Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.
Emergency calls
This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions. Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).
On BLUETOOTH communication

  •  Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident.
  •  where inflammable gas is present, in a hospital,  train, airplane, or petrol station
    •  near automatic doors or a fire alarm
  • This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.
  • We do not take any responsibility for the leakage of information during BLUETOOTH communication.

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

Guide to Parts and Controls

Main Unit and Remote Commander

Main unit

  1. (browse)
    During playback:
    Enters the browse mode.
    (Not available when a USB device in Android™ mode or iPod is connected.)
    PTY (program type)
    During FM reception:
    Selects PTY in RDS.

  2. SRC (source)
    Turns on the power.
    Changes the source.
    OFF
    Press and hold for 1 second to turn the source off and display the clock.
    Press and hold for more than 2 seconds to turn off the power and the display.
    If the unit is turned off and the display disappears, operation by the remote commander is not available

  3. EXTRA BASS
    Reinforces bass sound in synchronization with the volume level.
    Press to change the EXTRA BASS setting: [1], [2],
    [OFF].

  4.  Display window

  5.  USB port

  6.  (SEEK –/+)
    During radio reception:
    Tunes in radio stations automatically.
    Press and hold to tune manually.

    • prev/next)
    • (fast-reverse/fast-forward)
  7. MODE
    (back)
    Returns to the previous display.

  8. CALL
    Enters the call menu. Receives/ends a call.
    Press and hold for more than 2 seconds to switch the BLUETOOTH signal

  9. Receptor for the remote commander

  10. Number buttons (1 to 6)
    Receives preset radio stations.
    Press and hold to preset stations.
    ALBUM
    Skips an album for audio device.
    Press and hold to skip albums continuously.
    (Not available when a USB device in Android mode or iPod is connected.)
    (repeat)
    (Not available when a USB device in Android mode is connected.)
    ( shuffle)
    (Not available when a USB device in Android mode is connected.)
    MIC

    •  (play/pause)
  11. Control dial
    Adjusts the volume.
    PUSH ENTER
    Enters the selected item.
    Press SRC, rotate then press to change the source (timeout in 2 seconds).
    MENU
    Opens the setup menu.
    VOICE
    Press and hold for more than 2 seconds to activate voice dial, voice recognition (Android smartphone only), or the Siri function (iPhone only).

  12. AUX input jack

  13. DSPL (display)
    Changes display items.
    SCRL (scroll)
    Press and hold to scroll a display item.
    The VOL (volume) + button has a tactile dot.

RM-X231 Remote commander

SOUND
Opens the SOUND menu directly.
MENU
Press and hold to open the setup menu.

  1. Setting Menu
    Selects a setup item, etc.
    ENTER
    Enters the selected item.
    Press and hold for more than 2 seconds to establish or terminate the “Sony | Music Center” function.

  2. Setting Menu
    (prev/next)

  * +/– (album +/–)
  1. V OL (volume) +/–
    Remove the insulation film before use.
Basic Operations

Resetting the Unit

Before operating the unit for the first time, after replacing the car battery, or changing the connections, you must reset the unit.

  1.  Press and hold DSPL and CALL for more than 2 seconds.
    Note
    Resetting the unit will erase the clock setting and some stored contents

Setting the display language
After resetting the unit, the display language setting display appears.

  1. Press ENTER while [LANGUAGE] is displayed.
    The display language currently set appears.

  2. Rotate the control dial to select [ENGLISH] or [SPANISH], then press it.
    The setting is complete and the clock is displayed.

This setting can be configured in the general setup menu.

Switching the FM/AM Tuning Step

Set the FM/AM tuning step of your country or region. This setting appears only while the source is off and the clock is displayed.

  1.  Press MENU, rotate the control dial to select [GENERAL], then press it.
  2. Rotate the control dial to select [TUNER STEP], then press it.
  3. Rotate the control dial to select from [50K/9K], [100K/10K] or [200K/10K], thenmpress it.
Pairing with a BLUETOOTH Device

When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other. This unit can connect two BLUETOOTH devices (two mobile phones, or a mobile phone and an audio device).

  1. Press MENU, then rotate and press the
    control dial to select [BLUETOOTH] 
    [PAIRING]  [DEVICE 1]/[DEVICE 2]*.
    flashes while the unit is in pairing standby
    mode.
    [DEVICE 1] or [DEVICE 2] will be changed to the paired device name after pairing is complete.

  2. Perform pairing on the BLUETOOTH
    device so it detects this unit.

  3. Select your model name shown in the display of the BLUETOOTH device*.
    When pairing is made, stays lit.
    If passkey input is required on the BLUETOOTHdevice, input [0000].

Canceling the Demonstration Mode

You can cancel the demonstration display which appears when the source is off and the clock is displayed.

  1. Press MENU, rotate the control dial to select [GENERAL], then press it.

  2. Rotate the control dial to select [DEMO], then press it.

  3. Rotate the control dial to select [DEMOOFF], then press it.
    The setting is complete.

  4. Press (back) twice.
    The display returns to normal reception/play mode.

Updating the Firmware
To update the firmware, visit the support site on the back cover, then follow the online instructions.
Notes

  • Using a USB device (not supplied) is required for updating the firmware. Store the updater in the USB device, and connect the device to the USB port, then perform the update operation.
  • Updating the firmware takes a few minutes to complete. During the update, do not turn the ignition to the OFF position, nor remove the USB device.

Additional Information

Precautions
  •  Cool off the unit beforehand if your car has been parked in direct sunlight.
  • Do not leave audio devices brought in inside the car, or it may cause malfunction due to high temperature in direct sunlight.
  • Power antenna (aerial) extends automatically.
    To maintain high sound quality
    Do not splash liquid onto the unit

Playback order of audio files

About iPod

You can connect to the following iPod models.
Update your iPod devices to the latest software before use.
Compatible iPhone/iPod models

Compatible Model Bluetooth® USB
iPhone XR
  • |

iPhone Xs max|

  • |

iPhone Xs|

  • |

iPhone X|

  • |

iPhone 8|

  • |

iPhone 8 Plus|

  • |

iPhone 7|

  • |

|

  • |

iPhone SE|

  • |

iPhone 6s|

  • |

iPhone 6s Plus|

  • |

iPhone 6|

  • |

iPhone 6 Plus|

  • |

iPhone 5s|

  • |

iPhone 5c|

  • |

iPhone 5|

  • |

|

  • |

iPod touch

(6th generation)

|

  • |

iPod touch

(5th generation)

|

  • |

iPod nano

(7th generation)

|

  • |

  • Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
    Please note that the use of this accessory with an Apple product may affect wireless performance.

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

Maintenance

Replacing the lithium battery (CR2025) of the remote commander
When the battery becomes weak, the range of the remote commander becomes shorter.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Note on the lithium battery
Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor.

Specifications

Tuner section FM
Tuning range:

87.5 MHz – 108.0 MHz (at 50 kHz step)
87.5 MHz – 108.0 MHz (at 100 kHz step)
87.5 MHz – 107.9 MHz (at 200 kHz step)

FM tuning step:
50 kHz/100 kHz/200 kHz switchable
Usable sensitivity: 7 dBf
Signal-to-noise ratio: 73 dB
Separation: 50 dB at 1 kHz
AM
Tuning range:
531 kHz – 1,602 kHz (at 9 kHz step)
530 kHz – 1,710 kHz (at 10 kHz step)
AM tuning step:
9 kHz/10 kHz switchable
Sensitivity: 26 μV
USB Player section
Interface: USB (Full speed)
Maximum current: 1 A
Maximum number of recognizable folders and files:
Folders (albums): 256
Files (tracks) per folder: 256
Compatible Android Open Accessory protocol
(AOA): 2.0
Corresponding codec:
MP3 (.mp3)Bit rate: 8 kbps – 320 kbps (Supports VBR
(Variable Bit Rate))
Sampling rate: 16 kHz – 48 kHz
WMA (.wma)
Bit rate: 32 kbps – 192 kbps (Supports VBR
(Variable Bit Rate))
Sampling rate: 32 kHz, 44.1 kHz, 48 kHz
AAC (.m4a, .mp4)
Bit rate: 16 kbps – 320 kbps (stereo)
Sampling rate: 8 kHz – 48 kHz
FLAC (.flac)
Bit depth: 16 bit, 24 bit
Sampling rate: 44.1 kHz, 48 kHz
Supported file system: FAT16, FAT32

Wireless Communication
Communication System:
BLUETOOTH Standard version 3.0
Output:
BLUETOOTH Standard Power Class 2
(Max. Conducted +1 dBm)
Maximum communication range1:
Line of sight approx. 10 m (33 ft)
Frequency band:
2.4 GHz band (2.4000 GHz – 2.4835 GHz)
Modulation method: FHSS
Compatible BLUETOOTH Profiles
2:
A2DP (Advanced Audio Distribution Profile) 1.3
AVRCP (Audio Video Remote Control Profile) 1.3
HFP (Handsfree Profile) 1.6
PBAP (Phone Book Access Profile)
SPP (Serial Port Profile)
Corresponding codec:
SBC (.sbc), AAC (.m4a)

  1.  The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna (aerial)’s performance, operating system, software application, etc.
  2. BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices.

Power amplifier section
Output: Speaker outputs
Speaker impedance: 4 Ω – 8 Ω
Maximum power output: 55 W × 4 (at 4 Ω)
General
Power requirements: 12 V DC car battery (negative
ground (earth))
Rated current consumption: 10 A
Dimensions:
Approx. 178 mm × 100 mm × 177 mm
(7 1/8 in × 4 in × 7 in) (w/h/d)
Mounting dimensions:
Approx. 182 mm × 111 mm × 159 mm
(7 1/4 in × 4 3/8 in × 6 3/8 in) (w/h/d)
Mass: Approx. 1.0 kg (2 lb 4 oz)
Package contents:
Main unit (1)
Remote commander (1): RM-X231
Parts for installation and connections (1 set)
Optional accessories/equipment:
Cable for steering wheel remote input: RC-SR1 Ask the dealer for detailed information.
Design and specifications are subject to change without notice

Copyrights

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
This product is protected by certain intellectual
property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary.
Apple, iPhone, iPod, iPod nano, iPod touch, and Siri  are trademarks of Apple Inc., registered in the U.S. and other countries.
Android is a trademark of Google LLC.

Connection/Installation

Cautions

  • Run all ground (earth) leads to a common ground (earth) point.
  • Do not get the leads trapped under a screw, or caught in moving parts (e.g., seat railing).
  • Before making connections, turn the car ignition off to avoid short circuits.
  • Connect the yellow and red power supply leads only after all other leads have been connected.
  • Be sure to insulate any loose unconnected leads with electrical tape for safety.
  • Choose the installation location carefully so that the unit will not interfere with normal driving operations.
  • Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.
    Use only the supplied mounting hardware for a safe and secure installation.

Not e on the power supply lead (yellow)
When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating.
Note on installing in cars with a start-stop system
The unit may restart when starting the engine from start-stop. In this case, turn off the start-stop system of your car.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.

Parts List for Installation
  1. Mounting screws
    (5 × max. 8 mm
    (7/32 × max. 5/16 in)) (4)

  2. Power supply leads (1)

  3. Microphone (1)SONY-DSX-B700-FM-or-AM-Bluetooth-Car-Audio-09

  4. Double-sided tape (1)

SONY-DSX-B700-FM-or-AM-Bluetooth-Car-Audio-10

This parts list does not include all the package contents.

Connection
  1. Not supplied

  2.  Speaker impedance: 4 Ω to 8 Ω × 4

  3. RCA pin cord (not supplied)

  4. Depending on the type of car, use an adaptor for a wired remote control (not supplied).* 1 Not supplied
    For details on using the wired remote control, see “Using the wired remote control” (page 13).

  5. Whether in use or not, route the microphone input cord such that it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet.
    For details on installing the microphone, see “Installing the microphone” (page 13)
    Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit.

Making connections
  • To a common ground (earth) point
    First connect the black ground (earth) lead, the connect the yellow and red power supply leads.

  • To the +12 V power terminal which is energized at all times
    Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

  • To the +12 V power terminal which is energized when the ignition switch is set to the accessory position
    If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times.
    Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

  •   To the power antenna (aerial) control lead or
    the power supply lead of the antenna (aerial) booster
    It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).
    To AMP REMOTE IN of an optional power amplifier
    This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit.

  • To a car’s illumination signal
    Be sure to first connect the black ground (earth) lead to a common ground (earth) point.
    Subwoofer Easy Connection
    You can use a subwoofer without a power amplifier when it is connected to a rear speaker lead

Note
Use a subwoofer with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.
Memory hold connection
When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Speaker connection

  • Before connecting the speakers, turn the unit off.
  • Use speakers with an impedance of 4 Ω to 8 Ω, and with adequate power handling capacities to avoid damage.

Installing the microphone

To capture your voice during handsfree calling, you need to install the microphone .

Cautions

  •  It is extremely dangerous if the cord becomes wound around the steering column or gearstick.
    Be sure to keep it and other parts from interfering with your driving operations.

  • If airbags or any other shock-absorbing equipment is in your car, contact the store where you purchased this unit, or the car dealer, before installation.
    Note
    Before attaching the double-sided tape , clean the surface of the dashboard with a dry cloth.

Using the wired remote control

To enable the wired remote control, set [STR CONTROL] in [STEERING] to [PRESET].

Installation

Mounting the unit in the dashboard

Mounting the unit with an installation kit (not supplied)
You can use a commercially available double DIN installation kit. Choose an installation kit with the following panel frame size.
Larger than 172 mm × 97 mm (6 7/8 in × 3 7/8 in) (w/ h), with an inner corner radius of less than 0.5 mm (1/32 in).
Note
Be sure to use the mounting screws 

Mounting the unit in a Japanese car

You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.

When mounting this unit to the preinstalled brackets of your car, use the mounting screws  in the appropriate screw holes based on your car: T for TOYOTA and N for NISSAN.

Note
To prevent malfunction, install only with the mounting screws

Resetting the unit

For details, see “Resetting the Unit” (page 6).

Fuse replacement

When replacing the fuse, be sure to use one matching the amperage rating stated on theoriginal fuse. If the fuse blows, check the power connection andreplace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals