RYOBI RY18BLXC-0 Cordless Blower Instruction Manual

RYOBI RY18BLXC-0 Cordless Blower Instruction Manual

Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Safety, performance, and dependability have been given top priority in the design of your cordless blower.

INTENDED USE

The cordless blower is intended only for outdoor use, in dry, and well- illuminated conditions. The product is not intended to be used by children or persons with reduced physical, mental, or sensory capabilities. The product is designed for blowing light debris, such as leaves, grass, and other garden waste. Do not use the product for any other purpose.

GENERAL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re, and/or serious injury. Save all warnings and instructions for future reference.

WARNING! Never allow children or people who are unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.

TRAINING

• Read the instructions carefully. Be familiar with the controls and the correct use of the product.
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property.
• Do not use the product while tired, ill, or under the influence of drugs, alcohol, or medication.

PREPARATION

• Some regions have regulations that restrict the use of the product to some operations. Check with your local authority for advice.
• Wear hearing protection at all times whilst operating the product. This will prevent exposure to noise that could cause a permanent hearing injury. Protection such as ear plugs can limit your exposure and reduce noise.
• Wear full eye protection at all times while operating the product. Wear a full face mask or fully enclosed goggles. Normal spectacles or sunglasses are not adequate protection. Objects can be thrown at high speed by the powerful air jet at any time and may rebound from hard surfaces toward the operator.
• While operating the product, always wear substantial footwear and long trousers. Do not operate the product when barefoot or wearing open sandals. Avoid wearing clothing with loose fitting or that has hanging cords or ties.
• Do not wear loose clothing or jewellery that can be drawn into the air inlet. Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
• Before each use, ensure that all controls and safety devices function correctly. Do not use the product if the off switch does not stop the product.
• Operate the product in the recommended position and only on a firm and level surface.
• Do not operate the product on a paved or gravel surface where ejected material could cause injury.
• Before each use, always inspect the housing for damage. Ensure that guards and handles are in place and properly secured. Replace worn or damaged components in sets to preserve balance. Replace damaged or unreadable labels.
• Never operate the product while people, especially children, or pets are nearby.
• Keep all cooling air inlets clear of debris.
• Use rakes and brooms to loosen debris before blowing.
• Clear the work area before each use. Remove all objects such as rocks, broken glass, nails, wire, or string that can be blown a considerable distance by high velocity air.
• Injuries may be caused or aggravated by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery pack terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery pack; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery pack may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion, or risk of injury.
• Do not expose a battery pack or tool to fire or excessive temperatures. Exposure to fire or excessive temperature above 130°C may cause explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

OPERATION

• Operate the product only at reasonable hours—not early in the morning or late at night when people might be disturbed.
• Never operate the product in an explosive atmosphere.
• Avoid using the product in bad weather conditions, especially when there is a risk of lightning.
• Keep bystanders, children, and pets 15 m away from the area of operation. Stop the product if anyone enters the area.
• Do not operate the product in poor lighting. The operator requires a clear view of the work area to identify potential hazards.
• Operating similar tools nearby increases both the risk of hearing injury and the potential for other persons to enter your working area.
• Always be sure of your footing on slopes. Walk, never run.
• Keep proper footing and balance. Do not overreach. Overreaching can result in loss of balance.

BLOWER SAFETY WARNINGS

• Wear a face filter mask in dusty conditions to reduce the risk of injury associated with the inhalation of dust.
• Slightly dampen surfaces in dusty conditions.
• Do not use the product near open windows.
• Use the full blower nozzle extension so that the air stream can work close to the ground and perform effectively.
• Do not point the blower nozzle in the direction of people or pets.
• Never place objects inside the blower tubes.
• Do not place the product on top of or near loose debris. Debris can be sucked into the intake vent, resulting in possible damage to the product.

ADDITIONAL BATTERY SAFETY WARNINGS

To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse the tool, battery pack or charger in fl uid or allow fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater, certain industrial chemicals, and bleach or bleachcontaining products, etc., can cause a short circuit

TRANSPORTATION AND STORAGE

• Turn off the product, remove the battery pack, and allow it to cool down before storing or transporting.
• Remove all foreign materials from the product. Store the product in a cool, dry, and well-ventilated place that is inaccessible to children. Keep the product away from corrosive agents, such as garden chemicals and de-icing salts. Do not store the product outdoors.
• For transportation in a vehicle, secure the product against movement or falling to prevent injury to persons or damage to the product.

TRANSPORTING LITHIUM BATTERIES
Transport the battery pack in accordance with local and national provisions and regulations. Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, nonconductive caps or tape. Do not transport battery packs that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, can contribute to poor performance, and may void your warranty. Servicing requires extreme care and knowledge and should be performed only by a qualifi ed service technician. Have the product serviced by an authorised service centre only

• Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure that the product is in safe working condition. Any part that is damaged should be properly repaired or replaced by an authorised service centre.
• Bring the product to an authorised service centre to replace damaged or unreadable labels.
• You may make adjustments or repairs that are described in this manual. For other repairs, contact an authorised service centre.
• After each use, clean the product with a soft, dry cloth.

CLEARING A BLOCKAGE

• To reduce the risk of injury associated with contacting moving parts, always turn off the product, remove the battery pack, and make sure that all moving parts have come to a complete stop.
• Remove the blower tubes to inspect for blockage. Clear the tubes if required.
• Reinstall the blower tubes before starting the product.

KNOW YOUR PRODUCT

1. Blower tube
2. Blower tube latch
3. Variable speed trigger
4. Handle
5. Operator’s manual
6. Battery pack
7. Charger

SYMBOLS ON THE PRODUCT

 Read and understand all instructions before operating the product. Follow all warnings and safety instructions.

 Beware of thrown or fl ying objects. Keep all bystanders, especially children, and pets, at least 15 m away from the operating area.

 Rotating fans. Keep hands and feet out of openings while the product is running.

Wear ear protection.

Wear eye protection.

Do not expose the product to rain or damp condition.

 European Conformity Mark

 British Conformity Mark

 EurAsian Conformity Mark

 Ukraine Conformity Mark

 Guaranteed sound power level

Waste electrical products should not be disposed of with household waste. Recycle where facilities exist. Check with your local authority or retailer for recycling advice.

SYMBOLS IN THIS MANUAL

 Note
 Warning
 Parts or accessories are sold separately

WARNING
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of exposure. The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ. These conditions may significantly increase the exposure levels over the total working period. An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is running idle. These conditions may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the accessories, keeping the hands warm (in case of vibration), and organising work patterns.

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

1. The warranty period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newlyacquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
   • any damage to the product that is the result of improper or lack of maintenance
   • any product that has been altered or modified
   • any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
   • any damage caused by non-observance of the instruction manual
   • any product not displaying the CE approval mark on the rating plate
   • any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
   • any product connected to improper power supply (amps, voltage, frequency)
   • any product used with inappropriate fuel mixture (fuel, oil, ratio of oil/ fuel mixture)
   • any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
   • normal wear and tear spare parts
   • inappropriate use, overloading of the tool
   • use of non-approved accessories or parts
   • Accessories provided with the tool or purchased separately including but not limited to blades, saw chains, cutting lines, etc.
   • Any periodic adjustments to or maintenance cleaning of carburettors
   • Components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected.
6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE
Any request or issue with the product can be addressed to your local authorised service centres (visit www.ryobitools.eu) or directly to: Techtronic Industries GmbH, Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number and product type printed on the label.

EC DECLARATION OF CONFORMITY

Cordless blower
Brand: RYOBI | Model number1 | Serial number range2 We declare as the manufacturer under our sole responsibility that the product mentioned below fulfills all the relevant provisions of the following European Directives, European Regulations and harmonised standards3
Measured sound power level 96.7 dB(A)
Guaranteed sound power level 101 dB(A)
Conformity assessment method to Annex V Directive 2000/14/EC amended by 2005/88/EC. Authorised to compile the technical file:4

References

• Ryobi Tools
• Ryobi Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>