EXPERT HOME AF90P Face Recognition Door Lock Instruction Manual

Face Recognition Door Lock
User instruction Manual
V1.31 Edition
1 September

Dear user, Thanks for purchasing the smart face lock To improve the quality of life with innovative technology, to create the world’s most outstanding, most innovative products so that enterprises become the industry benchmark. We always adhere to the “quality survival, service, and development” business philosophy. In the intelligent lock industry, all constantly improve the product quality system. our company keeps up with the pace of the times . We always walk at the forefront of the industry, and always steadfastly protect the people’s property safety! From products to service, we always pursue to provide you with a full range of intimate and comfortable services! Thank you for your support for the smart face lock!
Disclaimer:
We have done our best to ensure that the information provided in this manual is correct and reliable, but we cannot fully guarantee errors before and during printing. Sometimes in order to improve the performance, reliability, and safety of components and systems, may upgrade the product, which may be somewhat inconsistent with the contents of the manual, but does not affect the actual operation, if there is a change that is not known, please understand! Our company will update the content regularly. If you have any questions, please call our company to answer. The final interpretation of the entire contents of this manual is the right of the Company. The functions described in this statement are not used as a reason for the use of this product for special purposes and the Company shall not be liable for accidents and hazards caused by the customer’s improper operation.

Safety and precautions

• Smart door lock as high-tech products, the installation of good or bad directly affect the normal operation and service life of the door lock, it is recommended that you install the door lock after the room has been decorated, please choose to ensure the quality of personnel to install, the factory strictly according to the company’s installation standards for operation
• Do not use it in environments with strong radiation, high magnetic field, and high temperature with corrosive substances, so as not to affect the performance and life of the smart lock.
• Please initialize the door lock as soon as the door lock installation is completed and restore the lock to the initial state. And please set your electronic key Settings immediately after initialization to prevent others from illegally opening your door lock.
• To ensure your safety, please check the key box carefully when you get the lock.
• Please properly protect your self-set electronic keys and mechanical keys.
• In order to better feel the convenience and advancement of the company’s products, please carefully read this manual before use, if there are any doubts, can directly to the company’s customer service center or headquarters service center, the company has professional technical personnel for your eyes, to ensure your use of rest assured.
• If you need to know more about the company or if your instructions were inadvertently lost, you can log on to our website for inquiries and downloads.
• Please please take my company’s web address to your computer, in order to find our company’s service information and product description at any time Functional features Verify Verification supports face, palm veins, fingerprint, IC card, password, mechanical key, and WeChat program dynamic code and other ways of authentication. After the user has successfully verified, the lock is on and the door is locked again after five seconds (time can also be adjusted to 3 seconds)
  The following authentication mode is supported to unlock:
  •Face
  •Palm veins
  •IC Card
  •Password
  •Fingerprint
  •WeChat Mini Program
  •Mechanical keys
  •The combination mode unlocks

01. Support face, Palm veins, IC card, password, fingerprint, mechanical key, WeChat Mini Program seven single door unlock, also can set the combination of door unlock, face, palm vein, IC card, the password any 2 mode combination of unlocking.
02, large storage capacity, this product can store 100 faces, 100 sets of palm veins,100 sets of fingerprints, 20 sets of cards, 5 sets of passwords, and 100 sets of users
03, this product uses standard Heaven -Earth straight lock body, the use of flexible extension function is strong, can choose the heavens and the earth pole device
04, This product left and right open direction of the free interchange
Note
1 This lock only supports M1 cards and does not recognize other types of cards
2 This lock does not support dual identification card mode, for example, cards on other products, it can not be used for face recognition lock.

Configuration list

Thank you for purchasing the smart Lock series, when you open the box, please check the inside you find that the above contents are missing from the box, please contact the local dealer as soon as possible to ensure prove your use.

Appearance dimension drawing

|

Door lock installation structure diagram

Instructions for use

1.  The door lock can be used when there is no registration state, and face recognition and password can be used to open the door.
   **Boot up
   After the first boot, please set it according to the icon “  in the lower right. A super password box will pop up in the interface, as shown below
   Note: Need to set it first, then enter the super password ‘123456 ” then press “ ” and finally enter the new six-digit super password 3 times, everyone entering a 6-digit code should click “ ” to operate the next group password. When the input is complete, you go straight to the menu function, operating other registered users, and the super password has the supreme authority of smart locks, please don’t leak!**

Please follow the voice prompts to operate!

2, enter the menu 2.1. has set up the administrator The user touches the upper right corner ”  ****“, and the smart lock is turned on into the authentication interface. Click the menu key ” ” in the lower right corner of the screen, and if an administrator is already enrolled (the default registered user number 1-5 is an administrator), the smart lock screen will prompt to verify the administrator’s identity, as shown below

The user verifies the administrator’s successfully to enter the menu (verify by face, palm vein, password, or IC card)

A. User setting
The user setting menu is used to add users and select the user management interface at the touch of a button on the LCD screen. The user setting interface consists of a list of “new users” and added users. Click “New users” to add new users. Click any one ID number in the list of added users to enter this user editing interface for editing.
IAdd New Users.’ menu:

1. Job number: each user has a unique number, this number is automatically generated by the system, and can not modify in the user setting
2. Name: set the user name for the new user
3. Permissions: set the user as an administrator or ordinary user
4. Palm vein: add the user’s palm vein
5. Face: Add the user’s face
6. Fingerprint: add the user’s fingerprint
7. Password: add the user to unlock password 8.
8. card code: add the user’s IC card
9. Delete
   Please press the up and down icon to move, then can select the desired verification method to set up a registration

Add new user: 1 job number 2 name 3. permission
4, add the palm vein
Enter to add the “palm vein” interface, the system voice prompt “Please put the palm in the green box”, as shown in the following image After the user hears the voice prompt, the palm will be entered parallel to the camera 20-35CM distance, and the system captures the information of the user’s palm. Please pay attention to the “di” sound to indicate that the palm vein information is being captured. If the palm position does not meet the requirements, the system stops the capture (“di” sound interruption), I re- position the finger in the correct position, and the system restarts to capture the palm vein information. em begins to captureagainPalm vein information. Note: When the palm vein is recognized, needs to be stretched out and the five fingers are separated (do not hold your fingers together)
5, add face
Go to add face interface, in order to get the correct frontal features of the user, the system will voice the “Please look at the camera”. After the user hears the voice prompt, the screen displays the camera’s real-time image and moves The face places the eyes in the green box on the screen. The face level to be entered Line camera 30-50CM distance. Note that the system emits a “drop” sound indicating positive Capturing facial images. If the facial position does not meet the requirements, The Council stops capturing(the “drop” sound is interrupted) and restores the face to the correct Set, the system restarts to capture facial information.

6, add fingerprint
Enter to enroll fingerprint interface. When enrolled once, the menu will show successfully and show “4”, After entering the fingerprint registration three times it will appear “successfully ” window .and the system voice prompt” Enroll successfully “.
7. Add a password
Enter to add password interface, and input the same password (4-8 digits ) twice, please click ” “V ” to save. As shown picture I
8, add IC card
Enter to enroll card interface, and the system will auto prompt “please swipe card “, and put the card near the IC card sensing area, After identifying the card code and clicking settings, the system automatically reads and saves the card information.
Note 1: Permission Description
The system default No. 1-5 for administrator, when the user adds an administrator, the administrator can use face, password and other any one mode to login in menu „
Note 2: Delete user
Select any registration number in the user list, you can go to the user’s editing interface, click “9. Delete” to remove this user from the system
B, Device settings
Can change some parameters of the smart lock in the Device settings menu.

1. Ordinary settings
   1.1 Language: Set the language of the smart lock menu display and voice prompt. Includes Simple Chinese, English, and traditional Chinese. 1.2 Date format: Format the date display. 1.3 Volume Settings: Set the volume of the smart lock prompt language.The rating numbers 1-8. 1.4 Battery voltage: The battery voltage used by the smart lock. Users use it with caution!

2. Advanced settings
   2.1 Delete all records: Delete all access records saved in the smart lock system.
   2.2 Delete all users: Delete all registered user information saved in the smart lock system.
   2.3 Recovery factory setting: the smart lock system of the parameters is restored to the factory state.

3. Communication settings
   (The standard setting’s menu with this function, but can not be used, it is an optional network module then can use.
   3.1 Add network
   3.2 Delete network
   3.3 Network on (on/off)

4. Take a picture setting 4.1 Invalid Photo Yes/No
   C, Equipment test, user caution!
   Equipment Test the menu is used by technical engineers to inspect equipment.

D. Security settings

1. Super Password: Set up and modify the smart lock super password, it has the highest privilege of smart lock, do not disclose. Users use it with caution!
2. Infrared switch: set the smart lock human induction switch.
3. Human induction distance: set smart lock human induction of high, medium, and low three gears. Users use it with caution!
4. Human induction time: set the intelligent lock human induction time fast, and slow.
5. motor torque: set the intelligent lock motor torque of high, medium, and low three gears. Users use it with caution!
6. Motor turnaround time: set the smart lock to control the signal length of the internal unlocking motor. Users use it with caution!
7. Rotary time: set the rotation time of the intelligent lock motor after unlocking Users use it with caution!
8. Opening direction: set the intelligent lock control internal lock motor forward, reverse state. Users use it with caution!
9. Timed lock: set the smart lock to unlock, and automatically return to the standby state (locked ) for the length of time, in seconds. (Set between 5 to 40S, set time of 0, and turn off the timing lock function)
10. Tamper button: set the switch for the smart lock tamper alarm.
11. Confirmation: Set the opening method for a single mode unlock or combination mode unlock

E, time settings
Time setting: The date and time used to set the current clock for the smart lock.
F. Device information menu is used to view the information on the equipment

1. Total capacity Used to view the capacity of the device registration information that a device can accommodate
2. Registration information The registration information of the registered user in the device
3. Record viewing Used to view information about the lock record in the device.
4. Equipment information is
   Used to view the algorithm version of the device, firmware version, and so on.
   Additional instructions
   (1) The system will automatically exit after more than 20 seconds of operation in the menu interface
   (2) In the power-on interface, if more than 10 seconds without operation, it will automatically turn off the screen standby, then need to press again ****to boot up.

The keypad of the rear panel’s handle section

1.  The front button of the rear panel handle position of the door lock is divided into an unlocking button, a locked button, and a clear button (The front key has one middle hole).
2. Unlock button: short press unlock key can open the door lock (voice prompt: please open door)
3. Locked button: short press lock key can close the door lock (voice prompt: door locked)
4. Clear button: smart lock power-on case, long press Clear button 3 to 5 seconds. It will pop up the initialization prompt box, click Yes/ No initialization success, smart machine voice prompt “restore factory settings”, click cancel will be directly returned.

Door lock outer panel section

1. infrared light wake-up function: people close to the infrared lamp 30 to 50cm can wake up the face part, such as unlock or lock it after 20 seconds before you can wake up the face part again.
2. Doorbell key: Touch the doorbell icon to prompt the doorbell, as shown in
3. Locked button: touch the anti-lock icon to close the door lock (voice prompt: I wish you go out safely), as shown in the picture

WIFI function (optional) needs to add a WIFI module
I. Official Wechat Account Connection

1. Search and connect the “Youzhiyunjia” official Wechat account, and enter it, as shown below
2. Click on “WeChat Control*, If you have registered the account then direct login, otherwise register, and then log in, as shown below
3. The first login in, it needs to be set ” security password’, which means remote unlock, as follows:
4.  After logging in, enter the device settings of the door lock menu, enter the communication settings menu, select WIFI to open, then click to add WIFI, lock motherboard setting WIFI module “hot spot connection” time-out time is “3 minutes, over time need to re-click the switch activation.
5. Click on the upper right corner “+” to add the device, as shown below:
6. At this time, Wechat back to the back of the phone, enter ‘setting — –WIFI list”, and operate the fingerprint lock into the “hot spot connection”, at this time the WIFI list will appear in the “CloudHome” open WIFI name, select the connection, enter a fixed password ‘11223344″ (or do not enter a password to connect), after the success of the connection, some Android phones will appear, “This WIFI is not available”, Please select ‘ still use this network’, switch the official Wechat account, appear the corresponding WIFI list, select the WIFI to use, select the WIFI to use, and enter the correct WIFI password, as follows:
7. As shown above, the door lock was added successfully. When the door lock inputs the “l+V” password interface, the APP normally receives the lock’s message and remote unlock, as shown in the following image:
8. Delete the user enter device settings in the door lock menu —- the communication settings, select WIFI to delete, Or click more in APP, then click more setting, click to delete a setting, also delete a device, as shown in the following image:

App remote unlock (Optional)

1.  Download the APR. Use WeChat, UC browser, and other software to scan the packaging of the QR code, download the “Youzhi Yunhome” APP http://www.kiwik.cn/app/smarthome/qr/?vendor=10
2. User registration/login. For the first time, you need to register a user, and enter a mobile phone number or email address to register users; If have an account, the user can log in directly.
3. After logging in, enter the device settings of the door lock menu, enter the communication settings menu, select WIFI to open, then click to add WIFI, lock motherboard setting WIFI module °hot spot connection’ time-out time is “3 minutes”, over time need to re-click the switch activation.
4. Make sure that your phone is connected to the WIFI name that begins with •CloudHome”, open the “Youzhiyunjia APP”, and click on the”My” page ” My device ” upper right corner “+” button Add door lock. Here’s the picture:
5. Click the next step to set up the graphical password interface, set your unlock password twice according to the tips, and then click on the “next step” to start configuring WiFi hotspots (hot spots in your own home).
6. When it connects the door lock successfully, it will di-di twice and prompt to add successfully and the user’s ID number on the panel, please remember the user ID. The user ID is a voucher used to specify who will unlock it in the future., (added the first phone for the administrator phone), while the APP will show the newly discovered device, If the device is not connected to the network, try to re-operate and add it again in the APP.
7. After the device is added successfully, according to the guidance of the APP, select the device to add the room where the device is located. You can add to an existing room, or create a new room as needed. You can then start using the device normally. Here’s the picture:
8. Remote unlock operation, enter “1 + V”, triggers a remote lock-opening request. Here’s the picture:

Additional instructions

1. The system will automatically exit after more than 30 seconds without operation in the menu
2. In the power-on interface, after more than 10 seconds without operation, it will automatically turn off the screen, need to press the power key to wake up again
3. In the upper left of the main interface, show the time date

Smart lock password WeChat Mini Program

|
---|---
https://mp.weixin.qq.com/a/~JFvGbrUNNvT7W7hxmRB-Tg~~

1. Access to the smart temporary password Mini Program interface
2. Enter the super password of the lock (6 digits password)
3. Enter the super password after clicking to start, the Mini Program automatically generates an 8-bit temporary dynamic password effective for 5 minutes.
4. Click on the main screen ” ****“, enter the main interface, click the lower left corner “ ” input temporary dynamic password, verify to open door.

Note: The Mini Program generated password without time management version, it should only be used when the smart lock is not powered, the system time and the real-time difference! Please user changes the battery to reset the system’s time.
Note : The Time and date on the Phone must be the same as the face smart lock.

Cats Eye using instructions(OPTIONAL)

1. Button: the device with 3 buttons — Confirm, Up, and Downward; Confirm: Functions confirm; Up Upper, Shot picture or records video(Under the video mode, this button can be started and stopped, if picture mode, it as shot picture). Downward: downward, menu

2. Operation instructions A, Press the Doorbell icon device turns on. Long press the “downward” button( if under video record, please press “Up” stop video first, and then press “Downward” and will show the menu as picture 1. Once the menu as picture 1, press “Up” or ” Downward” choose the sub-menu, and press confirms button. Enter into the “Picture” bar, browse the pictures been stored, and press “Up” or “Downward” to change the picture. Enter the “Video” bar to play the video, press “Up” or “Downward” to change the video, and press confirms button to start play.
   Enter the “Setting” bar as Picture 2
   Press “Up” or “Downward” to choose the column need to amend, then press the “Confirm” button for confirming. After amended, long press “downward” return to the main menu, and long press again for close. Long press “confirm” exit menu program, return to camera status. In the state of no menu, such as the default machine for recording mode press the “Up” button to pause and start recording, if the machine is in camera mode press the “Up” button to take photos.
   B. Press “confirm” in the shutdown state o boot into the camera screen.
   C, Press the doorbell button when the machine is turned off to take photos or videos and play the ringtone. If you press the doorbell button n the boot state, the machine repeats the ring. Press the “confirm” button and the machine will not record or take pictures, nor play the ringtone. Power-on photography or video recording is determined by setting the current working mode of the machine, which is in the mode of photography or video recording.

3. Reset In case of failure due o improper operation or other reasons the machine can be forced to reset and shut down by pressing “Confirm” and “downward” at the same time. Press the doorbell or “confirm” button to turn it on.

lock using
Power

1. Support lithium batteries or external power supply
2. 2. Battery life depends on battery type and usage habits. Experimental test conditions can be used for 4-5 months.
3. Emergency external power supply: USB mobile power supply (SV)

Emergencies

1. In any case, the door can be opened from the room. Open the door from the outside and it must be verified before it can be opened.
2. You can’t verify: a: you are using a card or password, but you have lost or forgotten. b Power off or the battery is not powered, in which case the lock cannot be started.
3. In any case, the mechanical key can be unlocked. If your battery is not powered and can’t open the door, you can use the SV USB mobile power back into the emergency unlock through the emergency external power outlet.
   Note: The emergency external power outlet only allows a 5V mobile power supply to start up.

User permission level

1. The facial recognition lock supports 2 permission levels: ordinary account and management account.
2. The ordinary account can unlock, but can not manage the door lock, can not register users, or change other functional operations.
3. Management account has full permission control for door lock, can be added, modified, deleted or other functional actions, administrator support by face recognition/palm vein / IC card/password recognition verification.

System parameters

Unlocking mode: Face, palm vein, fingerprint, IC card, password (combinable mode unlock) WeChat Mini Program dynamic code and key Static current: 50 microamps Operating current: 300 mAh (high drive capacity)
Capacity of open faces: .< =100
Capacity of open palm veins: < =100
Capacity of open fingerprints: < =100
Capacity of open passwords: < =5
Capacity of open cards: < =20
Camera: Infrared and Color Camera
Display: 3.5-inch TFT touch LCD
Start-up time: <1 second
FAR: 0.0001%
FOR: 0.01%
Recognition speed: 0.5 seconds
Low voltage alarm: 6.8V
Power supply voltage: 8.4V lithium battery power supply
Emergency power supply: 5V/2A (charge treasure available)
Working environment:
Identification distance: 30 to 80cm
Humidity: < 80%
Temperature: -20 to 60 degrees
Suitable for door thickness: 45-90MM

Warranty Card

The Company provides life-long maintenance for the sale of products, from the date of purchase within one year, the company provides free warranty service; If the following cases are not held for free warranty services:

1. If there is no product warranty card or valid purchase voucher, the warranty card and purchase certificate do not match the product
2. Damage caused by human factors, including use in an abnormal working environment, damage caused by the use of a non-stated manual, etc.;
3. The user’s private dismantling, self-repair, modification or maintenance by a non-authorized unit of the Company or other irresistible factors damaged”

User name|

 Contact Tel

---|---
Address|
Model No|

hock cylinder Noi

Serial No|
Purchase date|

 Install date   I

|
Supplier|
Contact man,|
Contact Tel|

Note to users:

In order to protect your legal rights, please keep the service card and the relevant purchase voucher, to protect your legal rights in warranty services, the warranty card once modified will be invalid

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>