Husqvarna PEDHQZ242 Kohler Zero Turn Mower Instruction Manual
- June 9, 2024
- Husqvarna
Table of Contents
HUSQVARNA® Striping Kit
MOUNTING INSTRUCTIONS
PEDHQZ242 Kohler Zero Turn Mower
IMPROTANT
Big League Lawns, LLC warrants their products to be free of defects in
material and workmanship. This warranty does not cover defects due directly or
indirectly to misuse, abuse, normal wear and tear, failure to properly
maintain the product or used for a purpose other than that for which it is
intended. The duration of this warranty is expressly limited to one year parts
and labor beginning from the date of delivery to the original user.
The obligation of Big League Lawns, LLC is limited solely to the repair or
replacement, at our option, at its factory or authorized repair agent of any
part that should prove deficient. Purchaser must maintain the product under
normal operating conditions at all times. Prior to operation, become farniliar
with the attachment and quick
disconnect teatures. This product is not intended to be used ina transport
position or to be backed over curbs. When not in use, the product should be
removed from the mower and transported in a safe manner. Failure to follow
these instructions will void the warranty.
PZ/PZT
Step 1: Remove existing 3/8”-16 x 1” bolts from each side of the frame at
noted location.
Step 2: Align the top holes of the CheckMate™ Mounting Plate (pointing up
in a U shape) with each of the holes from step 1.
Step 3: Reinstall both 3/8”-16 x 1” bolts through the CheckMate™ mounting plate and the mower frame and attach with existing locknut.
Step 4: Pull 7/16” lynch pins from stabilizer pins
Step 5: Slide CheckMate™ mounting arms onto stabilizer pins and replace lynch
pins
Step 6: Using (4) 1/2” x 1” hex bolts, attach mounting arms to striping kit
frame [finger tight] Step 7: Center roller behind the machine and tighten
mounting arms to gray striping kit frame [min. 90 lbs. Torque]
Z200 Series
Step 1: Remove Nut #34
Step 2: Pull Bolt #24 from mower mainframe
Step 3: Align hole of CheckMate™ mounting bracket with newlexposed hole;
mounting bracket will drop down on the ‘inside’ of the mowers tubular framing
[e.g. engine side]
Step 4: Confirm that both quick release stabilizer pins are pointing in the
same direction for quick release application.
Step 5: Place (1) 5/16” flat washer onto bolt #24
Step 6: Reinstall Bolt #24 through CheckMate™ mounting bracket, engine guard
and mower mainframe
Step 7: Secure engine guard and CheckMate mounting arm in place by threading
Nut #34 back in place [minimum 90 lbs. Torque]
Step 8: Pull 7/16” lynch pins from stabilizer pins
Step 9: Slide CheckMate™ mounting arms onto stabilizer pinsand replace lynch
pins
Step 10: Using (4) 1/2” x 1” hex bolts, attach mounting arms to striping kit
frame [finger tight] Step 11: Center roller behind the machine and tighten
mountingarms to gray striping kit frame [min. 90 lbs. Torque]
MZ/MZT
Step 1: MZT Series only; please remove 5/8”-11 x 3.5” bolts which secure rollover protection bar to mower mainframe
Step 2: MZT Series only; align holes in CheckMateTM mounting plate with
exposed holes in rollover protection bar. Reinstall 5/8”-11 x 3.5 bolt and
tighten to secure plate and ROPS bar to mower mainframe
MZ Series only; align holes in CheckMateTM mounting plate with exposed holes in mower mainframe. Using supplied 5/8”-11 x 2” bolts, lock washers and nuts; tighten and secure plate to mower mainframe.