AND Weighing MS-70 Moisture Analyzer Instruction Manual

: June 9, 2024
: AND Weighing

Table of Contents

MS-70 Moisture Analyzer
Product Information:
Product Usage Instructions:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MS-70 Moisture Analyzer

Product Information:

The product is a set of four testing equipment models: MS-70,
MX-50, MF-50, and ML-50. The company manufacturing the product is
A&D Company, Limited. The product is available for purchase at
Test Equipment Depot located in Woburn, MA, USA. The contact number
for Test Equipment Depot is 781-665-1400 and their toll-free number
is 1-800-517-8431. Customers can also visit the website
www.TestEquipmentDepot.com to buy the product.

The model numbers of the four testing equipment are:

MS-70
MX-50
MF-50
ML-50

Product Usage Instructions:

Before using the product, customers should read the user manual
carefully and familiarize themselves with the product features and
usage instructions.

To use the testing equipment, follow these steps:

Turn on the device by pressing the power button.
Select the appropriate testing mode from the options
provided.
Connect the device to the object being tested using the
appropriate cables or probes.
Start the testing process by pressing the start button.
Observe the results displayed on the device’s screen.
If necessary, adjust the settings or parameters to get accurate
results.
Once the testing is complete, turn off the device and
disconnect it from the object being tested.

Note: Customers should follow all safety instructions provided
in the user manual while using the product.

MS-70 MX-50 MF-50 ML-50
5 Commonwealth Ave Woburn, MA 01801 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.TestEquipmentDepot.com

1WMPD4000477F

A&D Company, Limited

WARNING o Do not use a sample that could make a dangerous chemical reaction and cause an explosion or poisonous gas, when the sample is dried. o Keep flammables away from the analyzer. Parts of the analyzer become very hot. Materials placed near it might catch fire. o Do not use the analyzer in ambient ignitable gas. It may cause explosion and fire. o Use a power source (voltage, frequency, outlet type) adapted to the specification of the analyzer. If excessive voltage is used, the analyzer may overheat and be damage or cause a fire. o Turn off the power switch and remove the power cord from the power outlet, when replacing the halogen lamp. Touching an electrode of the halogen lamp connector carelessly, it may cause to receive an electric shock. o Do not disassemble the analyzer. It may cause an error, damage, receiving an electric shock or fire. If the analyzer needs service or repair, contact the local A&D dealer. o Avoid getting the analyzer wet. It is not a water-resistant structure. If there is leakage of liquid into the analyzer, it may cause damage to the analyzer or receiving electric shock. o Do not look at the active halogen lamp to protect your eyes from damage. o Do not drop, hit or crack the glassware including the halogen lamp, to avoid an injury. o When the halogen lamp is used beyond 5000 hours, we recommend replacing the lamp with a new one to avoid trouble. o When discarding a halogen lamp, do not break it to avoid scattering glass and injury.
CAUTION o Do not touch the heater cover, the halogen lamp, glass-housing, pan handle, sample pan and sample without adequate protection, it could cause a burn or scald. Parts of the analyzer are very hot when a measurement finishes. For operation, use the specified grips of the heater cover and pan handle. Use the standard accessory tools. o Do not touch parts affixed with the & mark, because they may get very hot and dangerous. o When the analyzer is used in a room where hot air does not diffuse, it may unexpectedly overheat. In this case, adjust the drying temperature or move the analyzer to a place with adequate ventilation. o Avoid leaving the analyzer in direct sunlight, as that could cause discoloration of the case or a malfunction.

Test Equipment Depot – 800.517.8431 – 5 Commonwealth Ave, Woburn, MA 01801 TestEquipmentDepot.com

MS-70 / MX-50 I MF-50 / ML-50

3

,:”,;”J >· H “,,1′”; r_'”:11 l<:·”-,””1/””,-z7′

,”0V’-;’/,f;:”;’ 1′:,1); “::’J.c-9-,c;z>;;;”)J:”‘:

.· ‘!J;. .Nn,easmn1:He,rn Bliieg,11ams· ·, · ><: ,.. ·. :, :;;,

‘.’

-l· .

‘

‘-

“” o/” ‘ ‘

it;Qffl’.tvlJttSl£{c,Jmiij,Kti’l1/il!lllll§,:.::.::.;.;;:.· ,.,

” ,-
. ,;.,:;

j::!’ ‘) ‘
,:

There are five analysis modes.

Measurement Programs

Drying Program

Analyzing mode to Finish Measurement

Heating pattern

MS-70, MX-50, MF-50

ML-50

Drying Temperature
MX-50 MS-70 MF-50
ML-50

Standard Mode Std

Measurement condition is automatically selected by ACCURACY and minimum

Standard drying Ramp drying Step drying

Standard drying

value of% display.

Quick Mode

When drying rate is less than preset termination value,

9uc

measurement is completed

Quick drying

automaticallv.

Automatic Mode
U-R
Timer Mode LJ-l::

When drying rate is less than preset termination value, measurement is completed automaticallv. Sample is dried for a preset time. 1 min. to 480min.

Standard drying Ramp drying Step drying

Standard drying

I I Manuau”·l n-Mode

Measurement is completed by the STOP key. Max.
480 min.

Drying rate: Change of moisture content per one minute [%/min]

30°c to
200°c

50°c to
200°c

Test Equipment Depot – 800.517.8431 – 5 Commonwealth Ave, Woburn, MA 01801 TestEquipmentDepot.com

26

MS-70 / MX-50 I MF-50 / ML-50

. J ra.ra., ,i;JJJD”11,aJjrn..:i,1ffi.i1@;tirn, ,fs.rns.!l).:. ..,,

“/”t/'”;n.·”IJ” ,,R’0′::,-/;r-,q~r,f,0″;,J’> r “‘””‘-“i, ,t”;: -.;;-, “”‘s”J”‘””‘”A ,,”” ;; ”ccf”h'” ::-:r. , .t,;>

A .s. :.···,;. ,/;,

o A standard mass of 20g or 50g can be used for the calibration o A 20g standard mass (AX-MX-41) is recommend. Caution o Avoid vibration and drafts that affect the calibration. If affected, the analyzer
may be unable to calibrate the weighing sensor. o Use a 20g mass for the calibration, because the height between the weighing
pan and glass-housing is 26 mm. If a tall mass is used, open the glass-housing
and avoid external influence.

12.2.1. Operation

1. Display the gram unit (of the weighing mode).

2. Install the weighing pan, pan support and pan handle. Close the heater cover.
3. Press and hold the I PROGRAM I key to display I CH I.

!Preparation I
IPress and hold”IO”D'”

4. Press the I SELECT I key to display I CAL I.

I [H

[RL

5. Press the I ENTER I key to display I CAL O I.

0

I I 6. If 20g mass is used, …… Press the ENTER key.

:,-·11 LrR,L un

I

I I Proceed to step 8.
If 50g mass is used, …… Press the SELECT key.

Proceed to step 7.

7. Press the [jJ or IT] key to select 50.000g.
I I Press the ENTER key to store it. I I [I;[], CAL O are displayed in order.

Sun.ununung

0

I End

I

I I, I I 8. When displaying CRL O press the ENTER key to input “Data to display ZERO”. The standard mass value is displayed (Example: 20g).

9. Open the heater cover and put the standard mass
I I on the center of the pan and press the ENTER I I key to input “mass value”. End is displayed.

Standard mass

10. Remove the mass to return to the weighing mode
I I If the report for GLP, GMP and ISO is to be
output (Refer to page 61), GLP is displayed. The output condition for the report is selected in the function table.

Remove mass
CLP

0.000g

Test Equipment Depot – 800.517.8431 – 5 Commonwealth Ave, Woburn, MA 01801

TestEquipmentDepot.com

MS-70 I MX-50 I MF-50 / ML-50

57

IJ,dII____ 616 ID number ____56, 61

Indicators

13

,nFo

1

I SO