Altronix EBRIDGE100SPR EoC Single Port Receiver Installation Guide

EBRIDGE100SPR EoC Single Port Receiver
**Installation Guide

**

eBridge100SPR EoC Receiver
Installation Guide

Overview:

Altronix eBridge100SPR passes data and sends power over the coax to eBridge200WPMT. Data transmission and power over the Coax is possible up to 300m. The maximum range from the headend to the PoE camera/device is 500m, taking into consideration that up to 100m of structured cable may be deployed at each end. Built-in IP management allows for remote camera reset, monitoring, and reporting via various IP protocols.
Note: Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3).

Features:

Agency Listings:

• UL/cUL Listed for Information Technology Equipment (UL 60950-1).
• CE European Conformity.

Input:

• 51-56VDC/60W max. power.*

Power Output:

• Total output power: 60W.

Ethernet:

• Connectivity: RJ45, auto-crossover.
• Wire type: 4-pair Cat-5 or better-structured cable.
• Distance: up to 100m.
• Speed: 100BaseT, half/full duplex, auto negotiation.

Coax:

• Distance: up to 300m.
• Connectivity: BNC, RG-59/U or similar.
• Throughput is rated to pass 100Mbps from camera to receiver. Data distances of up to 300m can be achieved. With the proper headend equipment, multiple Megapixel cameras can be used.

LED Indicators:

• Blue LED – Coax link connection.
• Green LED – Power.
• Yellow and Green LED (RJ45) IP Link status, 100Base-T/active.

Environmental:

• Operating temperature: ­ 20ºC to 50ºC (­ 4ºF to 122ºF).
• Storage temperature: ­ 30ºC to 70ºC (­ 22º to 158ºF).
• Humidity: 20 to 85%, non-condensing.

Applications:

• Works with Megapixel, HD720, HD1080, and VGA (SD) cameras (see note, pg. 2).
• Extend Network link distance in an industrial environment.
• Upgrade deployed CCTV Coax to a digital network in Retail, Hospitality, Arenas, Casinos, Airports, Schools, Hospitals, Transportation, etc.

Mechanical:

• Dimensions (W x L x H approx.): 3.5″ x 4.375″ x 1″ (88.9mm x 111.1mm x 25.4mm).
• *UL Listed Class 2 or limited power source.

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. eBridge100SPR is not intended to be connected to outside plant leads and should be installed indoors within the protected premises. The eBridge100SPR is intended for indoor use only.

1. Secure the unit to the desired mounting surface with a proper fastening device utilizing the unit’s mounting hole. The unit should be mounted in proximity to an ethernet switch/network, NVR or video server.
2. Connect 56VDC UL Listed Class 2 or limited power source to terminals marked [Power ­ Input +] (polarity observed) (Fig. 1, pg. 2). Use 22AWG-16AWG wire for this connection. Caution: 56VDC will be present on coax. The other end of the coax should only be connected to the eBridge200WPM.
3. Connect the structured cable from the ethernet switch/NVR (network video server) to the RJ45 jack marked [10/100 BaseT] (Fig. 1, pg. 2).
4. Connect Coax cable to BNC connector marked [Coax].
5. Refer to eBridge200WPM for proper connection and setup information.

Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080, and VGA (SD) cameras. It is important to note that some high resolution and high frame rate cameras may demand faster headend processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may show pixelation and latency. It is advisable to pretest the system if unsure. Alternatively, frame rate and resolution may be reduced to accommodate system equipment.

Technical Specifications:

Yellow (RJ45 connector): On – Link, Off – No Link, Blinking – Activity.
Green (RJ45 connector): On – 100Base-TX, Off – 10Base-T.
Environmental Conditions| Operating ambient temperature (UL60950-1): — 20°C to 50°C (— 4°F to 122°F).
Storage temperature: — 30°C to 70°C (— 22° to 158°F).
Relative humidity: 85%, +/— 5%.
Operating Altitude: — 304.8 to 2,000m.
Regulatory Compliance| UUcUL Listed for Information Technology Equipment (UL 60950-1).
CE European Conformity.
Weights (approx.)| Product: 5.1 oz. (0.144 kg) I Shipping: 7.76 oz. (0.22 kg)

Cable Type, Total Device Power, Data, and Power Distance:

60W Coax Application:

Altronix is not responsible for any typographical errors. ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
140 58th Street, Brooklyn, New York 11220 USA
718-567-8181
fax: 718-567-9056
website: www.altronix.com 
e-mail: info@altronix.com 
Lifetime Warranty
IIeBridge100SPR Rev. 102814

eBridge100SPR Installation Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>