Zhiwei Robotics UNIHIKER Innovative Open Source Hardware for Learning and Using Python User Manual
- June 9, 2024
- Zhiwei Robotics
Table of Contents
Zhiwei Robotics UNIHIKER Innovative Open Source Hardware for Learning and Using Python
Please read this manual carefully before using this product.
Getting started
Connect to a computer and wait for the logo to appear.
How to run the demo programs?
- Press the Home button to access the “Menu”.
- Select the “Run Programs” option, and find a “.py” file in the “demo folder”.
- Press the Home button to run or stop it.
How to connect to Wi-Fi?
- Select the “Network Info” option from the “Menu”.
- View the **IP address.
**
-
You can open UNIHIKER’s local web page by entering the IP address “10.1.2.3” in your browser.
-
Select “Network Settings” to Connect to your Wi-Fi.
How to use wirelessly?
-
Connect to a 5V power adapter and wait for the logo to appear.
-
Connect UNIHIKER via Wi-Fi for use.
Please visit https://wikien.unihiker.com for more information.
Tech Specs
Specification
Size| 51.6mmx83mmx13mm| Sensor| Button Microphone Light Sensor
Accelerometer Sensor Gyroscope Sensor
---|---|---|---
CPU| Quad-Core ARM Cortex- A35, up to 1.2GHz
RAM| 512MB
Flash| 16GB
OS| Debian Actuator| Led, Buzzer
Wi-Fi| 2.4G| Port| USB Type-C,USB-A
MicroSD
Gravity 3pin&4pin port Edge connect
BT| Bluetooth 4.0
Display| 2.8inch, 240×320, Touch Screen
MCU| GD32VF103 Power| 5V 2A for USB Type-C
Instructions for safe use
To avoid malfunction or damage to your UNIHIKER please observe the following:
- Do not expose to water or moisture.
- Do not place on a conductive surface whilst in operation.
- Do not expose to heat from any source; the UNIHIKER is designed for reliable operation at normal ambient room temperatures.
- Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors.
- Avoid handling the printed circuit board while it is powered Only handle by the edges to minimize the risk of electrostatic discharge damage.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
FAQ
| Q: | A: |
|---|---|
| Can not boot up. | Check the power supply connect tight again, and the voltage |
is within the required range.
Wi-Fi connection failed.| Please check whether the password is entered
incorrectly, and try again several times after checking.
If you meet the problem that cannot be resolved, please visit: https://wikien.unihiker.com/faq
Or send email to: unihiker@dfrobot.com
Please describe the problem as specific as possible.
Contact Us
Address:
Room 603, 2 Boyun Road, Pudong, Shanghai P.R.China
@UNIHIKER
@UNIHIKER
unihiker@dfrobot.com
https://www.unihiker.com
https://wikien.unihiker.com
Due to continuous improvement of the product, if there were any changes, sorry for no further notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>