enel x JuiceBox 3.0 NA WiFi, Bluetooth Module User Manual
- June 9, 2024
- enel x
Table of Contents
JuiceBox 3.0 NA
Wi-Fi / Bluetooth Module Manual
Scope
This document is applied to the Shielded Ultra Small Wi-Fi® 11b/g/n + Bluetooth® 5.1 Module, Model No. 1DX, of the manufacturer Murata Manufacturing Co. Ltd.
Description
Type 1DX is a module based on Infineon CYW4343W combo chipset which supports
Wi-Fi® 802.11b/g/n + Bluetooth® 5.1 BR/EDR/LE up to 65Mbps PHY data rate on
Wi-fi® and 3Mbps PHY data rate on Bluetooth®. The WLAN section supports SDIO
v2.0 interface and the Bluetooth® section supports high-speed 4-wire UART
interface and PCM for audio data.
The module is mounted on the Main Board of the Juice Box 3.0 NA.
Block Diagram
Pictures
Dimensions
| Marking | Meaning |
|---|---|
| A | Pin 1 Marking |
| B | Murata Logo |
| C | Module Type |
| D | Inspection Number |
Dimensions unit : mm
Mark| Dimensions| Mark| Dimensions| Mark|
Dimensions
---|---|---|---|---|---
L| 6.95 +/- 0.2| W| 5.15 +/- 0.2| T| 1.1 max.
al| 0.25 +/- 0.10| a2| 0.5 +/- 0.1| a3| 0.25 +/- 0.10
bl| 0.30 +/- 0.2| b2| 0.30 +/- 0.2| Cl| 0.50 +/- 0.1
c2| 0.50 +/- 0.1| c3| 0.375 +/- 0.100| el| 0.2 +/- 0.1
e2| 0.2 +/- 0.1| e3| 0.2 +/- 0.1| e4| 0.3 +/- 0.1
e5| 1.175 +/- 0.100| e6| 1.0 +/- 0.1| e7| 0.525 +/- 0.100
e8| 0.50 +/- 0.10| ml| 1.0 +/- 0.1| m2| 1.0 +/- 0.1
m3| 0.5 +/- 0.1| m4| 0.5 +/- 0.1| |
Structure
Pin Layout
No.| Terminal Name| No.| Terminal Name| No.|
Terminal Name
---|---|---|---|---|---
1| GND| 15| WL GPIO 4| 29| GND
2| BT_UART_RXD| 16| BT_I2S_d0| 30| VBAT
3| BT_UART_TXD| 17| WL_GPIO_2| 31| VIN_LDO
4| BT UART CTS N| 18| WL GPIO 1| 32| GND (SR PVSS)
5| BT_UART_RTS_N| 19| GND| 33| GND (SR_PVSS)
6| BT_GPIO_3| 20| SDIO_CLK| 34| SR_VLX
7| BT GPIO 4| 21| GND| 35| GND
8| BT_PCM_SYNC| 22| SDIO_CMD| 36| VIO
9| BT_PCM_IN| 23| SDIO_DATA_2| 37| LPO_IN (32kHz)
10| BT PCM OUT| 24| SDIO DATA 0| 38| BT HOST WAKE
11| BT_PCM_CLK| 25| SDIO_DATA_3| 39| BT_DEV_WAKE
12| GND| 26| SDIO_DATA_1| 40| GND
13| BT GPIO 5| 27| WL GPIO 0 HOST WAKE| 41| ANT
14| BT_REG_ON| 28| WL_REG_ON| 42-46| GND
Rating
| | min.| typ.| max.| unit
---|---|---|---|---|---
Specification Temperature Range| -10| 25| 55| deg.C
Specification Voltage| VBAT| 3.2| 3.6| 4.2| V
VDDIO| 1.71| 1.8 or 3.3| 3.63| V
Antenna Check
The concrete contents of a check are the following three points:
- It is the same type as the antenna type of antenna specifications. Confirm the same size as the Gerber file.
- An antenna gain is lower than a gain given in antenna specifications. Measure the gain, and confirm the peak gain is less than the application value (1.4dBi)
- The emission level is not getting worse. Measure the spurious and confirm degradation of less than 3dB than spurious value of worst of report used for the application.
Radio Certification Information
Enel X Way FCC ID: 2A5OV-LB1DX
Enel X Way ISED ID: 28561-LB1DX
Federal Communications Commission (FCC)
compliance statements
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body. This device is
intended only for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users
- The transmitter module may not be co-located with any other transmitter or antenna.
- The use of an antenna with gain less than 1.4 dBi.
As long as 3 conditions above are met, further transmitter test will not be required.
Industry Canada (IC) compliance statements
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference;
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person’s body.
RF Exposure requirements are met when installed in mobile equipment.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
- The antenna must be installed such that 20 cm is maintained between the
antenna and users, 2) The transmitter module may not be co-located with any
other transmitter or antenna.
3)The use of an antenna with gain less than 1.4 dBi.
As long as 3 conditions above are met, further transmitter test will not be required.
APPENDIX
Federal Communications Commission (FCC) and Industry Canada (IC) compliance
statements of JuiceBox 3.0 NA
FCC Compliance Statement
Part 15
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Enel X Way could void the
user’s authority to operate the equipment.
FCC ID
The equipment contains the FCC IDs 2A5OV-ST25, 2A5OV-LB1DX, RI7-LE910CXNF.
Formal notices required by the Industry Canada (“IC”)
Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC ID
The equipment contains the ICs 28561-ST25, 28561-LB1DX, 5131A-LE910CXNF
Mobile Devices
To ensure compliance with FCC and ISED RF exposure requirements this device
must be installed to provide a minimum of 20cm between the device and people.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>