DS18 JVOCE8 Marine Roll Cage Sound Bar Tower Sound System Owner’s Manual

OWNER’S MANUAL
JVOCE8
JEEP OR ATV ROLL CAGE POD WITH
DUAL 8″ HYBRID MID-RANGE
/ DRIVER HORN LOUDSPEAKERS

PERFECT FOR: JEEPS & ATVS

READ BEFORE INSTALLATION

1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
3. For easier assembly, we suggest you have all your tools in hand- Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
4. Use high quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas tank, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.
6. Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
8. Make sure that the mounting clamp is tight before leaving the dock.
9. Decide early what type of LED lighting you want (if any) and wire accordingly(NOTE :if you want “Dancing Light” look to the WiFi or RF or BT remote controlled LED light box. The easy way to have lighting … YOUR way!)

INSTALLATION EQUIPMENT

• An Electric Drill With Bits
• Allen / Hex Key / Wrench Set
• Philips Head And Standard Screw Drivers
• Wire Strippers
• Crimping Tool
• Vom (Electronic Volt Ohm Meter)
• Heat Shrink Tubing And Heat Gun
• Soldering Iron
• Electronic (Rosin Not Acid Core) solder

PACKAGING INCLUDES

1 x Jvoce Enclosure with dual PRO-HY8.4B Hybrid Loudspeaker
1 x Flat Bracket for Jeep JL roll cage
1 x Tube clamp adjustable 2″ to 3″ diameter
1 x 6mm Hex wrench chromed
1 x 5mm Hex wrench chromed
1 x 4mm Hex wrench chromed
1 x NBR pad
1 x safety Rope
1 x Thread locker glue
1 set of screws and stop washers

NOTE: The stainless steel hardware supplied with your speakers has been chosen to resist rust and corrosion. If the particular hardware supplied will not work for your installation purposes, please be sure to use only appropriate marine grade (stainless steel) mounting hardware.

INSTALLATION & CONNECTION OPTIONS

If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

| Blue LED (-)
---|---
| Red LED (-)
| Green LED (-)
| Black 12V DC (+)
| White Left Speaker (+)
| White/Black Left Speaker (-)
| Yellow Right Speaker (+)
| Yellow/Black Right Speaker (-)

To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

• Black wire”BK” connected to battery Positive (+) 12V
• White Color Light “R”; “B” and “G” connected to battery Negative (-)
• Green Color Light “G” connected to battery Negative (-)
• Red Color Light “R” connected to battery Negative (-)
• Blue Color Light “B” connected to battery Negative (-)
• Purple Color Light “R” and “B” connected to battery Negative (-)
• Yellow Color Light”R” and “G” connected to battery Negative (-)
• Cyan Color Light “B” and “G” connected to battery Negative (-)

| Blue LED (-)
---|---
| Red LED (-)
| Green LED (-)
| Black 12V DC (+)
| White Left Speaker (+)
| White/Black Left Speaker (-)
| Yellow Right Speaker (+)
| Yellow/Black Right Speaker (-)

INSTALLATION BEGINNING MOUNTING

Step 1: Remove tower speakers from the packaging and ALL hardware.
Step 2: Find a GOOD location that allows for easy wiring of the speaker (and LED lights)
-PLUS does NOT impair your movement around the location.
Step 3: Using the supplied 6mm hex wrench spin out the 4-M8 screw that holds the top clamp
Step 4: Drill a 15 – 20 mm hole on the bottom of the mounting tube and align the clamps WIRE OUT hole
Step 5: Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to the tube.
Step 6: Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe.

INSTALLATION

Step 7:Wrap the rubber pad around the pipe and align wire out hole According to the diagram.

Step 8: Push the wire into the tube, press on the rubber pad, and lock the top clamp.
Step 9: Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.
Step 10: If need be, rotate the speakers for best dispersion, this easily done by locating the 6mm & 4mm hex wrench set screw on the side of the clamp base, rotate the speaker/enclosure to the desired angle, once there… locking the screws tight. Avoid vibration, clamp loose!!!

Step 11: During the mounting process, you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT (see Tie-wrap solution below)

Step 12: When you want to install a flat mounting, remove the clamp and take out the 6 core through it into the flat mounting bracket, then assemble it, see depiction below.

GENERAL SPECIFICATIONS

Nominal Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual 8” / 211mm
Nominal Impedance . . . . . . . .  . . . . . . . . . . . . . . . . . . . . . . . . . 4+4 ohm
RMS Power handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 250W
MAX Power Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 500W
Sensitivity (1w/1m . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 99dB
Frequency Response . . . . . . . . . . . . . . . . . . . . .. . . . 60Hz-20KHz
Recommended Hi Pass Crossover . . . . . . . . . .. . . . . . . . . 80Hz

BODY / FEATURES
Enclosure Material . . . . . . . . . . . . . . . . . . . . . . High Density Plastic Molded with Color Injected
Marine Grade Type . . . . . . . . . . . . . . .  . . . . . . . . . . . . . . IP65 + UV Protected
RGB LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes, Around the Grill
Grill Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Plastic ABS injected
Pair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NO
Clamps. . . . . . . . . . . . . . . . . . . . 2 x Die-Cast Flat Bracket for Jeep JL Roll Cage or Universal Fit 2 x Tube Clamp Adjustable (2″~3″) 360 Degree Rotation Mounting, Buried Wire or Open Wire Mounting Optional, Included NBR Pad And Stainless Hardware (Screws, Stop Washers, Hexagon wrench, Safety Rope, Threadlocker Glue)

Front Logo . . . . . . . . .  . . . . . . . . . . . . . . . . . . . . . . . . Yes
Finish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Matte Black
Input Wire. . . . . . . . . . . . . . . . . . Speaker x 2 (Stereo Configuration) + RGB Lights

WOOFER SPECIFICATIONS
Voice Coil Diameter. . . . . . . . . . . . . . . . . . . . 1.5″ / 38.6mm
Cone Material. . . . . . . .  . . . . . . . . . . . . . . . . Waterproof Paper
Surround Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cloth
Basket Material . . . . . . . . . . . . . . .  . . . . . . . . . . . Aluminum
Magnet Material . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . Ferrite
Magnet Weight . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 27 Oz

DRIVER SPECIFICATIONS
Voice Coil Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . 1″ / 25.4mm
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High Compression Horn
Diaphragm Material . . . . . . . . . .  . . . . . . . . . . . . . . . . Titanium
Magnet Material . . . . . . . . . . . . . . . . . . . . . . . . . . . Neodymium
Crossover . . . . . . . . . . . . . .. . . . . . . . . . . . 6 dB/Oct Filter
Horn Diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . 3″ / 76.2mm

THIELE & SMALL PARAMETERS
Equivalent Volume . . . . . . . . . . . . . .. . . . . . . . . . . . Vas . . . . .. . 10.048L
Excursion (one way) . . . . . . . . . . . . . . . . . . . . . . . Xmax . . . . . . 9.2mm
Free Air Resonance. . . . . . . . . . . . . . . . . . . . . . . . . Fs . . . . . . . . . .135Hz
Total Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Qts . . . . . . . . . 1.011

MEASUREMENTS
Overall Width . . . . . . . . . . . . . . .  . . . . . . . . . . . . . 19.44″ / 494mm
Overall Depth . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 6.41″ / 163mm
Overall Height (without Clamp) . . . . . . . . . . .  . . . . . . . . . . . . . 10.11″ / 257mm

MEASUREMENTS

WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without notice.
Images may or may not include optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov

FOR MORE INFORMATION
PLEASE VISIT
DS18.COM

References

• Official DS18 Pro Audio Store - Speakers, Subwoofers, Amps & More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>