RYOBI R36XCLV10 36V HP Brushless 40cm Front Tine Cultivator Kit Instruction Manual
- June 9, 2024
- RYOBI
Table of Contents
- INTRODUCTION
- INTENDED USE
- GENERAL PRODUCT SAFETY WARNINGS
- CULTIVATOR SAFETY WARNINGS
- ADDITIONAL BATTERY SAFETY WARNINGS
- TRANSPORTATION AND STORAGE
- TRANSPORTING LITHIUM BATTERIES
- MAINTENANCE
- SYMBOLS ON THE PRODUCT
- SYMBOLS IN THIS MANUAL
- PRODUCT SPECIFICATIONS
- BATTERY AND CHARGER
- Documents / Resources
RYOBI R36XCLV10 36V HP Brushless 40cm Front Tine Cultivator Kit
INTRODUCTION
IMPORTANT
It is essential that you read the instructions in this manual before
assembling, operating, and maintaining the product.
Subject to technical modification.
Safety, performance, and dependability have been given top priority in the design of your cordless cultivator.
INTENDED USE
The cordless cultivator is intended only for outdoor use by a standing
operator walking with the product. For safety reasons, the product must be
adequately controlled by using two-handed operation at all times.
The product is designed for cultivating or loosening soil in an open domestic
garden area. The maximum working capacity of the product is 20 cm deep and 40
cm wide. The product should be used only as described in this manual.
Do not use the product for any other purpose.
GENERAL PRODUCT SAFETY WARNINGS
WARNING! Read all safety warnings, instructions, illustrations, and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire, and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains operated (corded)
or battery-operated (cordless) product.
WORK AREA SAFETY
- Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control
PERSONAL SAFETY
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
- Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
-
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
-
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with switch is dangerous and must be repaired.
-
Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
-
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users. -
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
-
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
-
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
-
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire
SERVICE
- Have your product serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
- Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorised service providers.
CULTIVATOR SAFETY WARNINGS
- Use the product across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes.
- Exercise extreme caution when reversing or pulling the product towards you.
- Never pick up or carry the product while the motor is running.
- Use the product only in daylight or with good artificial light.
- Keep proper footing and balance at all times, especially on slopes. Walk, never run.
- Do not use the product near drop-offs, ditches, excessively steep slopes, or embankments. Poor footing could cause a slip-and-fall accident.
- Avoid working the soil when soggy or wet. Wait a day or two after heavy rain for the ground to dry.
- Keep hands and feet away from the rotating tines at all times and especially when turning on the motor.
- Turn off the product, and remove the battery pack. Make sure that all moving parts have come to a complete stop:
- before leaving the product unattended
- before cleaning the product or clearing a blockage
- before checking for any damage after hitting an object
- if the machine starts to vibrate abnormally (check immediately)
- before performing maintenance
- Read the instructions carefully. Be familiar with the controls and the correct use of the product.
- Never allow children or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.
- Never operate the product while people, especially children, or pets are nearby. Keep in mind that the operator or user is responsible for accidents or hazards.
- While operating the product, always wear substantial footwear and long trousers. While operating the product always wear substantial footwear and long trousers.
- Thoroughly inspect the area where the product is to be used and remove all objects which can be thrown by the product.
- Before each use, always visually inspect to see, that the housing is undamaged and that guards and handles are in place and properly secured. Replace worn or damaged components in sets to preserve balance.
- Store the product in a location where the ambient temperature is between -10°C and 50°C.
- Operate the product only in temperatures between 0°C and 40°C
ADDITIONAL BATTERY SAFETY WARNINGS
- To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse the product, battery pack, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
- Charge the battery pack in a location where the ambient temperature is between 10 °C and 38°C.
- Store the battery pack in a location where the ambient temperature is between 0°C and 20°C.
- Use the battery pack in a location where the ambient temperature is between 0°C and 40°C.
TRANSPORTATION AND STORAGE
- Turn off the product, and remove the battery pack. Make sure that all moving parts have come to a complete stop. Allow the product to cool down before storing or transporting.
- Remove all foreign materials from the product. Store the product in a cool, dry, and well-ventilated place that is inaccessible to children. Keep the product away from corrosive agents, such as garden chemicals and deicing salts. Do not store the product outdoors.
- For transportation in a vehicle, secure the product against movement or falling to prevent injury to persons or damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery pack in accordance with local and national provisions and regulations. Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport battery packs that are cracked or leaking. Check with the forwarding company for further advice.
MAINTENANCE
- Use only original manufacturer’s replacement parts, accessories, and attachments. Failure to do so can cause possible injury, can contribute to poor performance, and may void your warranty.
- Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. Have the product serviced by an authorised service centre only.
- Check all nuts, bolts, and screws at frequent intervals for proper tightness to ensure that the product is in safe working condition.
SYMBOLS ON THE PRODUCT
| Safety alert
---|---
| Beware of thrown or flying objects. Keep all bystanders, especially children
and pets, at least 15 m away from the operating area.
| Read and understand all instructions before operating the product. Follow
all warnings and safety instructions.
| Wear eye protection.
| Wear hearing protection
| Keep hands away from rotating tine
| Keep feet away from rotating tines.
| To prevent serious injury, do not touch the rotating tines.
| Do not expose the product to rain or damp conditions.
| Regulatory Compliance Mark. Product meets applicable regulatory
requirements.
| Guaranteed sound power level
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist Check with your local authority or
retailer for recycling advice.
SYMBOLS IN THIS MANUAL
| Parts
or accessories sold separately
---|---
| Note
| Warning
Operating Instructions
R36XCLV10
-
Wear full eye and ear protection, gloves, substantial footwear, and long trousers at all times while operating the product.
-
On the left side of the metal frame, install the wheel into the axle. Insert and turn the nut clockwise using the wrench to secure the wheel. On the right side of the metal frame, install the wheel into the axle. Insert and turn the nut clockwise using the wrench to secure the wheel.
-
Install a hub cap on both sides of the metal frame.
-
Attach the right middle tube to the upper handle shaft using bolts and nuts. Turn the nuts clockwise using the wrench to secure the right middle tube. Attach the left middle tube to the upper handle shaft using bolts and nuts. Turn the nuts clockwise using the wrench to secure the upper left middle tube.
-
Attach the middle tubes to the lower handle shafts using bolts and nuts. Turn the nuts clockwise using the wrench to secure both middle tubes.
-
Insert a lock pin into the inner hole of the right tine shaft. Insert a hitch pin into the lock pin to secure the lock pin in place. Insert tine B over the right tine shaft until it reaches the lock pin. The stamped side of the tine should face towards the gearbox. Insert a lock pin through tine B and the center hole on the tine shaft. Insert a hitch pin into the lock pin to secure tine B.
-
Insert tine D over the right tine shaft until it reaches tine B. The stamped side of the tine D should face towards tine B.
Insert a lock pin through tine D and the outer hole on the tine shaft. Insert a hitch pin into the lock pin to secure tine D -
Insert a lock pin into the inner hole of the left tine shaft. Insert a hitch pin into the lock pin to secure the lock pin in place. Insert tine A over the left tine shaft until it reaches the lock pin. The stamped side of the tine should face towards the gearbox. Insert a lock pin through tine A and the center hole on the tine shaft.
Insert a hitch pin into the lock pin to secure tine A.
-
Insert tine C over the left tine shaft until it reaches tine A. The stamped side of the tine should face towards tine A. Insert a lock pin through tine C and the outer hole on the tine shaft. Insert a hitch pin into the lock pin.
-
Insert the drag stake inside the metal frame between the wheels. To secure the stake to the frame, insert the drag stake bracket through the holes of the metal frame and drag stake. Connect both ends of the drag stake bracket to secure the drag stake.
-
Open the battery door. Insert the battery pack into the battery slot
-
Close the battery door.
-
Press the on/off button and pull up the bail towards the handle.
FOUR-TINE OPERATION
WARNING: Keep hands and feet away from the rotating tines at all times.
WARNING: The product must be adequately controlled by using a two-handed
operation at all times.
WARNING: Never operate the product on rocky surfaces.
-
Insert the drag stake inside the metal frame. To secure the stake to the frame, insert the drag stake bracket through the holes on the metal frame and drag stake. Adjust the tilling depth according to the holes on the drag stake.
NOTE: For transport and surface tilling, set the drag stake to the first hole from the bottom. Adjust the wheel so that the drag stake can reach the soil’s surface.
NOTE: For medium tilling, set the drag stake to the third hole from the bottom. For deep tilling, set the drag stake to the sixth hole from the bottom. -
Open the battery door. Slide in the battery pack into the battery slot.
-
Close the battery door.
-
Press the on/off button and pull up the bail towards the handle. Use the speed selector switch to increase the power when necessary.
WARNING: x of time. Running at low speeds under constant usage may cause the product to overheat. -
Push the product while it is digging on the soil’s surface.
NOTE : Several passes over the same path may be required to reach the preferred depth. Do not try to dig too deeply in the first pass. If the product jumps or bucks, allow the product to move forward at a slightly faster rate or adjust the position of the wheel assembly
CLEANING THE PRODUCT
-
Open the battery door.
-
Slide out the battery pack from the battery slot. Close the battery door.
-
Clean the product with a soft, dry cloth.
Remove the debris from the tines with a stiff brush.
WARNING: Do not use water to clean the tines.
STORING THE PRODUCT
WARNING: Clean and remove all foreign materials from the product before storing.
-
Open the battery door.
-
Slide out the battery pack from the battery slot. Close the battery door.
-
Store the product in a cool, dry, and well-ventilated place that is inaccessible to children and well away from sources of ignition.
PRODUCT SPECIFICATIONS
Cordless cultivator
Model| R36XCLV10
Weight| 28.11 kg
Rated voltage| 36 V d.c.
No-load speed
High| 230-260 /min
Medium| 207-243 /min
Low| 185-225 /min
Tine diameter| 25.4 cm
Working width| 28 cm or 40 cm
Working depth| 20 cm
Noise emission values determined according to EN 709:1997+A4:2009
A–weighted sound pressure level at the operator position| 83.2 dB(A)
Uncertainty| 3.0 dB
A–weighted sound power level| 91.2 dB(A)
Uncertainty| 1.9 dB
Guaranteed sound power level| 93 dB(A)
Vibration values determined according to EN 709+1997+A4:2009| 0.6 m/s²
Uncertainty| 1.5 m/s²
BATTERY AND CHARGER
Model
| R36XCLV10| R36XCLV16
---|---|---
Battery pack| –|
BPL3660D
Charger
| –|
R36CHA4A0
Compatible battery packs
| |
BPL3620D, BPL3660D, BPL3690D, BPL3626D2, BPL3640D2, BPL3650D2, BPL3660D, BPL3612D, R36BTY2, R36BTY4, R36BTY5, R36BTY6, R36BTY8
Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
Documents / Resources
|
RYOBI R36XCLV10 36V HP Brushless 40cm Front Tine Cultivator
Kit
[pdf] Instruction Manual
R36XCLV10, R36XCLV16, R36XCLV10 36V HP Brushless 40cm Front Tine Cultivator
Kit, 36V HP Brushless 40cm Front Tine Cultivator Kit, HP Brushless 40cm Front
Tine Cultivator Kit, Brushless 40cm Front Tine Cultivator Kit, 40cm Front Tine
Cultivator Kit, Front Tine Cultivator Kit, Cultivator Kit
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>