CUCICU M1C Magnetic Wireless Charger User Manual
- June 10, 2024
- CUCICU
Table of Contents
M1C Magnetic Wireless Charger
User Manual
M1C Magnetic Wireless Charger
Thank you for using our products, please read the instruction card carefully before use
Specifications
Compatibility:
(Magnetic)iPhone 14 Pro Max/14 Pro/14 Plus/14/13 Pro Max/13 Pro/13/13 mini/12
Pro Max/12 Pro/12/12mini
(Magnetic)AirPods 3/AirPods Pro2/AirPods Pro
(Please use a magnetic case to charge your phone)
Description
This product has an adsorption function, which can accurately align the
charging position of the mobile phone.
(Mobile phone/phone case needs to be equipped with built-in magnet)
Important Reminders
- For maximum charging speed, use a cable and adaptor compatible with QC (Quick Charge) 2.0/3.0.Adapters are compatible with QC (Quick Charge) 2.0/3.0 or PD (Power Delivery) Quick Charge or PD (Power Delivery) fast charging.
- This charger can only be installed on a caseless iPhone with magnetic suction or the official MagSafe case and ESR Halolock case. It will not connect to any other phones or cases.
- The charger has a maximum output of 15W. The maximum output of the iPhone is 7.5W. The maximum output power of the headset is 5W.
Safety warning
-
Do not put this product into fire or water to avoid short circuit leakage or damage to the product.
-
Please check the product, data cable and other accessories before use.
Immediately stop using the product if you notice any damage. -
Do not use this product in a high temperature, humid or corrosive environment, so as not to damage the circuit and prevent charging or other
-
Do not contact the product with corrosive liquids, otherwise it will cause serious damage and the product will not be guaranteed.
-
Do not disassemble or modify this product for any reason, so as to avoid secondary failure and burning, which is not covered by the warranty
UK:
This device was tested for uncontrolled environment operations. To comply with
RF exposure requirements, a minimum separation distance of 20cm must be
maintained between the user’s body and the product.
Declaration of Conformity
Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd. declares that the
product type M1C is in compliance with following Regulations: Radio Equipment
Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and The
Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012. The full text of the UK declaration of
conformity is available at the following internet address:
https://www.YFZN.com/
EU:
This device was tested for uncontrolled environment operations. To comply with
RF exposure requirements, a minimum separation distance of 20cm must be
maintained between the user’s body and the product.
Declaration of Conformity
Hereby, Shenzhen Yifeng Intelligent Technology Co., Ltd.declares that the
product type M2 is in compliance with Directives 2014/53/EU & 2011/65/EU. The
full text of the EU declaration of conformity is available at the following
internet address: https://www.YFZN.com/
| Radiated H-Field | 6.6 dBuA/m (@10m) |
|---|---|
| TX/RX Frequency Range | 110-148kHz(Only for EU&UK) |
Shenzhen Yifeng Intelligent Technology Co., Ltd.
10th Floor, Building 2, Chaxi, Zone B, Huafeng First Science Park, Hangcheng
Street, Gushu, Baoan District, Shenzhen, China.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance between 20cm the radiator your body.
IC Caution:
Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
RF exposure statement:
The equipment complies with IC Radiation exposure limit set forth for
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>