KRIPOL Pure Sine Wave Inverter User Manual
- June 10, 2024
- KRIPOL
Table of Contents
Pure Sine Wave Inverter
Product Information
KRIPOL PURE SINE WAVE INVERTER
The KRIPOL Pure Sine Wave Inverter is a device that converts DC (Direct Current) power from a battery or solar panel into AC (Alternating Current) power, which is suitable for powering electrical and electronic equipment. It is designed to be used indoors and outdoors, and can be installed in two different ways – Method 1 (portable) and Method 2 (fixed installation).
Structure and Connection Diagrams
The inverter has a structure diagram and a connection diagram, which can be used as a reference while installing the device. The structure diagram shows the physical components of the inverter, while the connection diagram shows how the inverter should be connected to other devices.
Installation Location
While installing the inverter, please ensure that the ambient temperature is
below 50 degrees Celsius. Do not expose the inverter to water, rain, snow or
spray, as it may damage the device.
Additionally, do not block the cooling fan of the inverter, as it may affect
the heat dissipation.
Method 1: Portable Installation
The inverter can be carried freely without fixed installation and can be used anytime, anywhere, including indoors and outdoors.
To install the inverter using Method 1, follow these steps:
- Connect the battery or solar MPPT system to the inverter using the DC cable connection.
- Connect the AC load to the inverter using the AC outlet.
- If required, connect any USB devices to the USB port on the inverter.
The simplified schematic diagram shows how to connect the battery or solar MPPT system to the inverter.
Method 2: Fixed Installation
The inverter can also be installed using Method 2, which requires fixed installation. To install the inverter using Method 2, follow these steps:
- Refer to the recommended margins for fixed installation. The inverter has mounting holes on the edge of the device, so no additional drilling is required.
- Connect the battery or battery assembly (lead-acid batteries, lithium batteries, liquid batteries, etc.) to the inverter, ensuring that they meet the voltage requirements. For example, a DC 12V inverter requires a 12V battery.
- Connect any AC loads to the AC outlet on the inverter.
- If required, connect any USB devices to the USB port on the inverter.
- If using solar panels, connect them to the MPPT solar charge controller, and then connect the controller to the inverter using the DC cable connection.
- The cumulative battery should be connected to the inverter as shown in the example.
The AC connection diagram shows how to connect the AC load to the inverter.
CAUTION
The inverter is designed to be connected directly to standard electrical and electronic equipment, as described above. Do not connect the power inverter to household or RV AC distribution wiring. Additionally, do not connect the power inverter to any AC load circuit in which the Neutral conductor is connected to Ground (Earth) or to the Negative of the DC (battery) source. This inverter is not grid interactive.
Wireless Remote Control
The KRIPOL Pure Sine Wave Inverter comes with a wireless remote control, which can be used to turn the device on or off from a distance..
DETAILS OF OUR INVERTER
Structure Diagram(e.g. 20012-US )
Installation Location
- Please make sure your ambient temperature is below 50℃.
- Do not expose the inverter to water, rain, snow or spray.
- Do not block the cooling fan of the inverter, which will affect the heat dissipation.
Method 1: It can be carried freely without fixed installation and can be
used anytime, anywhere. Including indoor and outdoor.
Method 2: For fixed installation, please refer to the recommended
margins. (There are mounting holes on the edge of the inverter, no additional
drilling is required)
Installation Steps
Simplified schematic 
Battery or Battery Assembly 
EXAMPLE: DC 12V inverter
Solar MPPT System
DC Cable Connection 
AC Connection
- Make sure that the single load or the combined load requirement of your equipment does not exceed the inverter’s output rating. (For example, the load of a 2000W inverter is that the output of a single socket is within 2000W, or the sum of the loads of several AC sockets is within 2000W.
- Switch off the inverter
- Switch off the load
- Plug the cord(s) from the load(s) into the AC receptacle(s) of the inverter
- Switch on the inverter. Wait for a few seconds
- The LED display will be working to indicate that the inverter is functioning
- Switch on the load(s)
CAUTION
The inverter is engineered to be connected directly to standard electrical and
electronic equipment in the manner described above. Do not connect the power
inverter to household or RV AC distribution wiring. Do not connect the power
inverter to any AC load circuit in which the Neutral conductor is connected to
Ground (Earth) or to the Negative of the DC (battery) source.
Do not connect directly to AC distribution wiring. This inverter is not grid interactive.
Wireless Remote Control
Wireless remote control is a breakthrough of KRIPOL technology, which allows you to control from the inverter switch within the range of 50M-80M. Compared with no remote control or existing wired remote control, this remote control solves many troubles of long-distance and different space use.
- The inverter switch must be kept off before using the remote control.
- The remote control battery is configured to match the service life of the inverter, no need to replace the battery.
- If the remote control cannot be used, please contact the KRIPOL team in time, and we will replace it for you free of charge.
- The remote control is an electronic product. Keep away from water, fire and direct sunlight.
- The remote control has an induction antenna, please pull out the antenna when operating from a distance. (The remote control is not a toy, it is forbidden for children to play with it)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>