RYOBI ROS300 300W Corded Random Orbit Sander Instruction Manual
- June 10, 2024
- RYOBI
Table of Contents
RYOBI ROS300 300W Corded Random Orbit Sander
Product Information
The ROS300 is a power tool designed for sanding on wood surfaces, removing rust from and sanding steel surfaces, and sanding plastics. The tool operates on alternating current with a no-load speed of revolutions or reciprocations per minute. It has a pad size and orbital diameter of unspecified dimensions and features double insulation. The tool is designed for use with identical Ryobi replacement parts only to prevent hazards or product damage. When operating, users must wear safety goggles or safety glasses with side shields, dust masks, and ear protection. Additionally, they must wear safety hand gloves while unpacking or performing maintenance. The tool should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when not in use to prevent accidental starting that could cause serious injury. Users should avoid using solvents when cleaning plastic parts as most plastics are susceptible to various types of commercial solvents and may be damaged by their use.
Product Usage Instructions
- Wear safety goggles or safety glasses with side shields, dust masks, and ear protection before operating the tool.
- Ensure that the tool is not connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when not in use.
- Use identical Ryobi replacement parts only when servicing the tool.
- Avoid using solvents when cleaning plastic parts.
- Remove the sanding sheet from the sander before cleaning to prevent serious personal injury.
- Recycle raw materials instead of disposing of them as waste to promote environmental-friendly recycling.
- Refer to the user manual for more information on safety rules, lubrication, and environmental protection.
SPECIAL SAFETY RULES
- Always wear safety goggles and a dust mask when sanding, especially sanding overhead.
- A suitable breathing respirator must be worn while sanding lead paint, some woods and metal to avoid breathing the harmful/toxic dust or air.
INTENDED USE
You may use this product for the purposes listed below:
- Sanding on wood surfaces.
- Removing rust from and sanding steel surfaces.
- Sanding plastics.
MAINTENANCE
WARNING
- The tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury.
- When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.
GENERAL
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommend using this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using compressed air.
WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If the operation is dusty, also wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.
WARNING
Always remove the sanding sheet from the sander before cleaning. Failure to do so could cause serious personal injury.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of them as waste. The machine, accessories, and packaging should be sorted for environmental-friendly recycling.
SYMBOL
ICONS IN THIS MANUAL
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>