Bosta 73284100 Robotic Swimming Pool Cleaner Instruction Manual
- June 10, 2024
- Bosta
Table of Contents
73284100 Robotic Swimming Pool Cleaner
Instruction Manual
Read this instruction manual carefully before using your new robotic cleaner. Save for future reference.
Product Introduction
Human beings have liberated their hands because they walked upright. Even in
modern society with advanced technology, to liberated hands is still the
unremitting pursuit of
human beings. The swimming pool cleaning robot is developed for this purpose.
The cleaning robot is a kind of the underwater cleaner , it is fully
automatically. It is mainly used to clean the dirt and debris such as hair,
leaves and sand from the pool floor; pool wall and waterline. As long as you
put it into the pool after initial program setting, the
cleaning robot can automatically measure the size of the pool, automatically
design the working route, and clean the pool by itself.
Warning and Cautions
Warning: Your cleaner should not be used while people are swimming in the
pool. Do not allow swimmers in the pool while pool cleaner is operating.
Warning: Keep the cleaner away from Child, or use under adult’s strict
and close supervision.
Warning: DO NOT switch on the pool cleaner if it is not immersed in the
water. Operating the cleaner out of the water may cause severe damage and will
result in loss of warranty.
Warning: Always remember to turn the power supply off and unplug it from
the power outlet before removing the cleaner from the pool.
Warning: DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE.
Warning: To use this cleaner only when water temperature is 10-35! and
the depth of the pool is 0.5M-3M. The cleaner is designed to work for the pool
with 100M surface area.
Warning: Keep the controller box in a dry place which is 3.5m away from
your pool.
Operation Instructions
Brief Introduction
-
Start/Stop
Could measure the pool size automatically and set the working cycle. -
Mode of floor clean only
To only clean the pool floor to increase the clean efficiency. -
Mode of all purpose clean
All-around cleaning, including pool floor; pool wall and waterline. -
Mode of waterline clean only
To quick clean the waterline only. -
Use App to control (not available for all models)
Operation Instructions:
- Connect floating power cord.
- Position the power supply so that it is approximately in the middle of the long side of the pool at a distance of 3.5m /11.5ft.
- Put the Pool Cleaner into the pool. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
- Turn the power supply ON ” 115V AC 60HZ# in the position $ One of the three modes light will be on. Press the button for the mode you want to run, then press ON/OFF button, the Pool Cleaner will now operate until it has reached the end of the cleaning cycle.
- Mode switching: Press on/off button, choose the mode, press on/off button to start the cleaner.
- Indicator lights%
LED Light | Status | Indication |
---|---|---|
White | On | Normal operation of the pool cleaner |
White | Blinking twice | Work reversely after meeting obstacles |
White | Always blinking | Bluetooth communication with the pool cleaner or |
standby status
Red| On| Overload or load protection Let the cleaner sink to the floor of the
pool, and press on/off to start again.
Routine Maintenance
-
Clean the filter basket
Turn off the Pool cleaner. Open the filter cover. Clean the filter basket with a hose. Insert the clean filter basket and close the filter cover. Make sure the power supply is switched off and unplugged.
It is highly recommended to clean the filter basket after each cleaning cycle. -
Use of filter paper coreThe filter paper core is a fragile part, which can filter particles below 5um, and its service life is less than 72 hours. (The filter paper core can be used without affecting the performance of the robot, and it is strongly recommended that the filter paper core be not used in the dirty swimming pool.)
-
Routine Maintenance of the floating cable
The floating cable may get twisted after 8 hours of continuous work, please untwist the cable then before re-start the pool cleaner. After each use, roll up the cable so that it has no kinks.
Trouble shooting
Symptom | Possible Reason | Corrective action |
---|---|---|
The pool cleaner moves but does not clean the pool | Clogged filter basket |
Clean the filter basket
The pool cleaner does not move| An obstacle blocks the impeller An obstacle
blocks the drive belt| Unplug the power supply. Open the impeller cover and
check that nothing is trapped in the impeller. Verify that nothing blocks the
tracks or wheels.
Debris out from the outlet| Filter basket is broken| Replace the filter basket
Filter basket is full| Clean the filter basket
The floating cable has kinks| Working for too long time, over 8 hours.|
Untwist the floating cable before re-start.
Stop working| Overload or load protection| Let the cleaner sink to the floor
of the pool, and press on/off to start again.
Specifications
Product dimension | 470 x 410x 255 mm |
---|---|
Package dimension | 680 x 330x 700 mm |
Product weight | Around 10.5 KG |
Package weight | Around 18 KG |
Cleaning area | Pool floor, pool wall, waterline |
Filtration accuracy | 5um |
Length of floating cable | 17m |
Filter speed | 14-18 m³ / h |
Output voltage | 24V DC |
Output current | 4.5A |
Input voltage | 115V |
Frequency | 60Hz |
Horsepower | 120W |
IP Class for controller box | IP65 |
IP Class for motor | IP68 |
1.Controller box | 8.Drive belt |
---|---|
2.Power cord for controller box | 9.Driven wheel |
3.Wheel brush | 10.Sleeve |
4.Main body | 11.Wheel brush |
5.Drive wheel | 12.Filter basket |
6.Drive wheel fixing block | 13.Floating cable |
7.Side panel | 14.Filter paper core |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>